Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › from 2014.12
RM2170E _51 Engine / Hybrid System _057004 HYBRID / BATTERY CONTROL _0277924 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P2532-772  Ignition Switch Run Position Circuit High  


DESCRIPTION

The power source and HV CPU processors and their functions are integrated into the hybrid vehicle control ECU. The power source CPU and HV CPU use CAN communication to communicate with each other inside the hybrid vehicle control ECU. The power source CPU controls the opening and closing of the IG2 relay. The HV CPU detects that the IG2 relay is stuck ON (closed) based on relay operation information received from the power source CPU via CAN communication.

DTC No. INF Code DTC Detection Condition Trouble Area
P2532 772 Voltage is still applied to IG2 terminal although an IG2 relay off command is received from the power source CPU.
·

Hybrid vehicle control ECU

·

No. 1 integration relay (IG2 relay)

·

Wire harness or connector



HINT:

If DTC P2532-772 is stored, the vehicle will turn off.


WIRING DIAGRAM

A345228E04
5.354,0.969 6.156,1.146 0.802,0.177 10 false A71 5.354,1.125 7.125,1.448 1.771,0.323 10 false Hybrid Vehicle Control ECU 4.323,2.354 7.146,2.677 2.823,0.323 10 false Certification ECU (Smart Key ECU Assembly) 5.802,0.615 6.313,0.792 0.51,0.177 10 false IG2 4.156,0.615 4.375,0.792 0.219,0.177 10 false 2D 4.188,0.406 4.406,0.583 0.219,0.177 10 false 4 4.198,0.854 4.417,1.031 0.219,0.177 10 false 3 4.156,1.052 4.375,1.229 0.219,0.177 10 false 2D 1.865,0.604 2.083,0.781 0.219,0.177 10 false 2E 1.896,0.406 2.115,0.583 0.219,0.177 10 false 1 1.896,0.844 2.115,1.021 0.219,0.177 10 false 2 1.865,1.042 2.083,1.219 0.219,0.177 10 false 2D 5.802,1.823 6.313,2 0.51,0.177 10 false IG2D 5.604,0.51 5.76,0.688 0.156,0.177 10 false 3 5.604,1.698 5.76,1.875 0.156,0.177 10 false 9 3.302,1.458 3.594,1.635 0.292,0.177 10 false IG2 2.354,1.885 4.083,2.063 1.729,0.177 10 false No. 1 Integration Relay 4.698,0.76 5.417,0.938 0.719,0.177 10 false IG2 NO. 2 2.469,0.771 2.76,0.948 0.292,0.177 10 false IG2 0.896,1.552 1.49,1.917 0.594,0.365 10 false Auxiliary Battery 0.792,0.99 1.198,1.208 0.406,0.219 10 false MAIN 1.177,0.771 1.448,0.927 0.271,0.156 10 false P/I 4.323,2.188 5.125,2.365 0.802,0.177 10 false G77

CAUTION / NOTICE / HINT

HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Turn the power switch on (IG) and wait for 15 seconds or more.

2.

Turn the power switch off and wait for 30 seconds or more.



PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / DTC.


d.

Check for DTCs.

Result
Result Proceed to
P2532-772 only is output. A
DTCs except P2532-772 are output. B


e.

Turn the power switch off.



A

2.READ VALUE USING INTELLIGENT TESTER (CAN BUS CHECK)

B

6.CHECK FOR INTERMITTENT PROBLEMS
2.READ VALUE USING INTELLIGENT TESTER (CAN BUS CHECK)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: System Select / Bus Check / Communication Bus Check.

Result
Result Proceed to
All of the ECUs and sensors that are currently connected to the CAN communication system are displayed. A
None of the ECUs and sensors that are currently connected to the CAN communication system are displayed, or some of them are not displayed. B


d.

Turn the power switch off.



A

3.CHECK HARNESS AND CONNECTOR (+B SHORT)

B

3.CHECK HARNESS AND CONNECTOR (+B SHORT)
a.
U183348E02
0.844,2.281 1.219,2.573 true 0.667,2.927 0.938,3.094 0.271,0.167 10 false A71 1.146,2.594 1.531,2.771 0.385,0.177 10 false IG2 0.177,0.073 0.333,0.24 0.156,0.167 10 false *a

Disconnect connector A71 from the hybrid vehicle control ECU.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A71-3 (IG2) - Body ground Power switch off 1 V or less


Text in Illustration
*a Rear view of wire harness connector
(to Hybrid Vehicle Control ECU)


c.

Connect the hybrid vehicle control ECU connector.



OK

NG

4.INSPECT NO.1 INTEGRATION RELAY (IG2 RELAY)
4.INSPECT NO.1 INTEGRATION RELAY (IG2 RELAY)

OK

5.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - IG2 RELAY)

NG

5.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - IG2 RELAY)
a.

Disconnect connector A71 from the hybrid vehicle control ECU.


b.

Remove the No. 1 integration relay from the No. 2 engine room relay block and No. 2 junction block assembly.


c.
U183348E02
0.844,2.281 1.219,2.573 true 0.667,2.927 0.938,3.094 0.271,0.167 10 false A71 1.146,2.594 1.531,2.771 0.385,0.177 10 false IG2 0.177,0.073 0.333,0.24 0.156,0.167 10 false *a

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A71-3 (IG2) - Body ground Power switch off 1 V or less


Text in Illustration
*a Rear view of wire harness connector
(to Hybrid Vehicle Control ECU)


d.

Install the No. 1 integration relay.


e.

Connect the hybrid vehicle control ECU connector.



OK

6.CHECK FOR INTERMITTENT PROBLEMS

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK FOR INTERMITTENT PROBLEMS

OK

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA