Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › 2014.12–2017.06
RM2170E _51 Engine / Hybrid System _057004 HYBRID / BATTERY CONTROL _0277924 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0A01-726  Motor Electronics Coolant Temperature Sensor Circuit Range / Performance  P0A04-725  Motor Electronics Coolant Temperature Sensor Circuit Intermittent  


DESCRIPTION

The hybrid vehicle control ECU detects HV coolant temperature using the coolant temperature sensor built into the inverter with converter assembly. The hybrid vehicle control ECU uses signals from the coolant temperature sensor to check the effectiveness of the inverter cooling system. If necessary, the hybrid vehicle control ECU will limit inverter output to help prevent inverter overheating. The hybrid vehicle control ECU also detects malfunctions in the sensor based on the HV coolant temperature sensor values. The inverter with converter assembly detects malfunctions in the HV coolant temperature sensor and its wiring.

DTC No. INF Code DTC Detection Condition Trouble Area
P0A01 726 Abnormal deviation in inverter coolant temperature sensor output. Both of the following conditions are met for 10 seconds or more:
1.

The difference between the estimated coolant (for inverter) temperature and the temperature sensor output is large.

2.

Coolant (for inverter) temperature is too high.


(1 trip detection logic)
·

Inverter cooling system

·

Cooling fan system

·

Inverter with converter assembly


P0A04 725 Sudden change in HV coolant temperature sensor output or hunting: Unusual sudden change in HV coolant temperature sensor output occurs and the offset continues for a certain period of time. Unusual sudden change in HV coolant temperature sensor output occurs repeatedly.
(1 trip detection logic)

CAUTION / NOTICE / HINT

CAUTION:
·

Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·

After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION).

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Turn the power switch on (READY) and wait for 90 seconds or more.

2.

Drive the vehicle for approximately 10 minutes referring to the following freeze frame data or Data List items: "Vehicle Spd".



PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Select the following menu items: Powertrain / Hybrid Control / DTC.


d.

Check if DTCs are output.

Result:
Result Proceed to
Only P0A01-726 or P0A04-725 is output, or DTCs other than the ones in the table below are also output. A
Any of the following DTCs are also output. B


DTC No. Relevant Diagnosis
P0A93-346 Inverter Cooling System Performance
P0C73-776 Motor Electronics Coolant Pump "A" Control Performance
P314A-828 Inverter Coolant Pump Speed Signal

HINT:

P0A01-726 or P0A04-725 may be set due to a malfunction which also causes DTCs in the preceding table to be set. In this case, first troubleshoot the output DTCs in the preceding table. Then, perform a test to attempt to reproduce the problems, and check that no DTCs are output.



e.

Turn the power switch off.



A

2.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

B

2.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

OK

3.CHECK QUANTITY OF HV COOLANT

NG

CONNECT SECURELY

3.CHECK QUANTITY OF HV COOLANT
a.

Check the HV coolant level in the inverter reserve tank.


b.

Check for HV coolant leaks.

Result
Result Proceed to
No leaks are found and coolant level in the inverter reserve tank assembly is above the low line. A
No leaks are found and coolant level in the inverter reserve tank assembly is below the low line. B
Coolant leaks are evident. C

HINT:

After repairing the HV coolant leaks and adding coolant, perform the "Activate the Water Pump" Active Test (HV Active Test item) and the "Control the Electric Cooling Fan" Active Test (Engine Active Test item) and make sure that there are no malfunctions.




A

4.CHECK COOLANT HOSE

B

ADD HV COOLANT

C

INSPECT FOR HV COOLANT LEAK AND ADD HV COOLANT

4.CHECK COOLANT HOSE
a.

Check if the hoses of the cooling system are kinked or clogged.



OK

5.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE ELECTRIC COOLING FAN)

NG

CORRECT THE PROBLEM

5.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE ELECTRIC COOLING FAN)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Clear DTCs and freeze frame data.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Electric Cooling Fan.


e.

Perform the "Control the Electric Cooling Fan" Active Test.

OK:

The cooling fan rotates.



f.

Turn the power switch off.



OK

6.CHECK HV COOLANT (CHECK FOR CONDITIONS THAT MAY HAVE CAUSED FREEZING)

NG

6.CHECK HV COOLANT (CHECK FOR CONDITIONS THAT MAY HAVE CAUSED FREEZING)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / DTC.


d.

Read the freeze frame data Ambient Temperature using the intelligent tester.


e.

Check if the freeze frame data Ambient Temperature is below freezing.

Result:
Result Proceed to
Ambient Temperature value is below freezing temperature of the HV coolant. A
Ambient Temperature value is above freezing temperature of the HV coolant. B


HINT:
·

HV coolant (SLLC) with a 30% concentration freezes at -15 °C (5°F) and HV coolant (SLLC) with a 50% concentration freezes at -35°C (-31°F).

·

If the HV coolant freezes in the HV radiator or HV water pump, the coolant temperature in the inverter with converter assembly rises because the HV coolant cannot circulate. As a result, a DTC may be set.

·

A DTC is set when the water pump impeller cannot rotate due to freezing of the HV coolant.

·

If a DTC is set due to freezing of HV coolant, the problem cannot be reproduced. Judge whether freezing of HV coolant occurred according to the freeze point of the HV coolant, HV coolant change history and ambient temperature when the DTC was set.




f.

Turn the power switch off.



A

7.REPLACE HV COOLANT

B

REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS

7.REPLACE HV COOLANT
a.

Replace the HV coolant with coolant having an appropriate concentration (appropriate freeze point) for the vehicle usage conditions (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>COOLANT(for Inverter)>REPLACEMENT).



NEXT

COMPLETED