Home › Engine / Hybrid System › 1NZ-FXE (COOLING) › COOLING FAN SYSTEM › 2011.12–2017.06
RM2170E _51 Engine / Hybrid System _057009 1NZ-FXE COOLING _0277971 COOLING FAN SYSTEM J

1NZ-FXE COOLING  COOLING FAN SYSTEM  Cooling Fan Circuit  


DESCRIPTION

The ECM calculates an appropriate cooling fan speed based on the engine coolant temperature, inverter coolant temperature, air conditioning switch condition, refrigerant pressure, engine speed and vehicle speed, and sends the signals to the cooling fan ECU to regulate the cooling fan. The cooling fan ECU controls the cooling fan speed based on the duty ratio signal sent from the ECM. By basing its control on the operating conditions, the ECM can control the fan speed optimally using the cooling fan ECU, achieving both high cooling performance and quietness.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE ELECTRIC COOLING FAN)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Electric Cooling Fan.


e.

Check the operation of the cooling fan while operating them using the tester.

OK:
Tester Operation Specified Condition
ON Cooling fan operating
OFF Cooling fan stopped


Result:
Result Proceed to
OK A
NG (Cooling fan does not operate) B
NG (Cooling fan does not stop) C




A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B

2.INSPECT COOLING FAN MOTOR

C

11.CHECK HARNESS AND CONNECTOR (ECM - COOLING FAN ECU)
2.INSPECT COOLING FAN MOTOR

OK

3.CHECK HARNESS AND CONNECTOR (COOLING FAN ECU POWER SOURCE)

NG

3.CHECK HARNESS AND CONNECTOR (COOLING FAN ECU POWER SOURCE)
a.
U183309E01
0.322,1.838 0.594,1.994 0.272,0.156 10 A52 0.181,0.155 0.338,0.310 0.157,0.156 10 *a 2.536,2.649 2.727,2.805 0.191,0.156 10 E1 2.093,2.085 2.588,2.629 false 0.641,2.649 0.914,2.805 0.272,0.156 10 +B1 1.366,2.085 0.87,2.629 false

Disconnect the cooling fan ECU connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A52-1 (+B1) - A52-3 (E1) Power switch on (IG) 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Cooling Fan ECU)



OK

4.CHECK HARNESS AND CONNECTOR (ECM - COOLING FAN ECU)

NG

5.CHECK HARNESS AND CONNECTOR (COOLING FAN ECU - BODY GROUND)
4.CHECK HARNESS AND CONNECTOR (ECM - COOLING FAN ECU)
a.

Disconnect the ECM connector.


b.

Disconnect the cooling fan ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A40-45 (RFC) or A52-2 (SI) - Body ground Always 10 kΩ or higher




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - COOLING FAN ECU)

5.CHECK HARNESS AND CONNECTOR (COOLING FAN ECU - BODY GROUND)
a.

Disconnect the cooling fan ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A52-3 (E1) - Body ground Always Below 1 Ω




OK

6.INSPECT COOLING FAN RELAY (FAN RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (COOLING FAN ECU - BODY GROUND)

6.INSPECT COOLING FAN RELAY (FAN RELAY)

OK

7.CHECK HARNESS AND CONNECTOR (FAN RELAY POWER SOURCE)

NG

REPLACE COOLING FAN RELAY (FAN RELAY)

7.CHECK HARNESS AND CONNECTOR (FAN RELAY POWER SOURCE)
a.
A269760E01
0.333,0.836 0.526,1.029 0.193,0.193 10 *1 1.844,0.291 2.037,0.484 0.193,0.193 10 *2

Remove the FAN relay from the No. 2 engine room relay block and No. 2 junction block assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3 (FAN relay) - Body ground Power switch off 11 to 14 V


Text in Illustration
*1 No. 2 Engine Room Relay Block and No. 2 Junction Block Assembly
*2 FAN Relay



OK

8.CHECK HARNESS AND CONNECTOR (COOLING FAN ECU - FAN RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (FAN RELAY - AUXILIARY BATTERY)

8.CHECK HARNESS AND CONNECTOR (COOLING FAN ECU - FAN RELAY)
a.

Remove the FAN relay from the No. 2 engine room relay block and No. 2 junction block assembly.


b.

Disconnect the cooling fan ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A52-1 (+B1) - 5 (FAN relay) Always Below 1 Ω
A52-1 (+B1) or 5 (FAN relay) - Body ground Always 10 kΩ or higher




OK

9.CHECK HARNESS AND CONNECTOR (FAN RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (COOLING FAN ECU - FAN RELAY)

9.CHECK HARNESS AND CONNECTOR (FAN RELAY - BODY GROUND)
a.

Remove the FAN relay from the No. 2 engine room relay block and No. 2 junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (FAN relay) - Body ground Always Below 1 Ω




OK

10.CHECK HARNESS AND CONNECTOR (FAN RELAY - NO. 1 INTEGRATION RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (FAN RELAY - BODY GROUND)

10.CHECK HARNESS AND CONNECTOR (FAN RELAY - NO. 1 INTEGRATION RELAY)
a.

Remove the FAN relay from the No. 2 engine room relay block and No. 2 junction block assembly.


b.

Disconnect the No. 1 integration relay connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1(FAN relay) - 2C-4 Always Below 1 Ω
1(FAN relay) or 2C-4 - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (FAN RELAY - NO. 1 INTEGRATION RELAY)

11.CHECK HARNESS AND CONNECTOR (ECM - COOLING FAN ECU)
a.

Disconnect the ECM connector.


b.

Disconnect the cooling fan ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A40-45 (RFC) - A52-2 (SI) Always Below 1 Ω




OK

12.CHECK HARNESS AND CONNECTOR (COOLING FAN MOTOR - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - COOLING FAN ECU)

12.CHECK HARNESS AND CONNECTOR (COOLING FAN MOTOR - BODY GROUND)
a.
U183272E02
1.573,0.083 1.781,0.302 0.208,0.219 10 false *a 0.708,1.156 0.979,1.313 0.271,0.156 10 false z4

Disconnect the cooling fan motor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z4-1 (-) - Body ground Always 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Cooling Fan Motor)



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG