Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › 2011.12–2014.12
RM2170E _51 Engine / Hybrid System _057004 HYBRID / BATTERY CONTROL _0277924 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0A1A-151  Generator Control Module  P0A1A-155  Generator Control Module  P0A1A-156  Generator Control Module  P0A1A-166  Generator Control Module  P0A1A-658  Generator Control Module  P0A1A-659  Generator Control Module  P0A1A-791  Generator Control Module  P0A1B-163  Drive Motor "A" Control Module  P0A1B-164  Drive Motor "A" Control Module  P0A1B-192  Drive Motor "A" Control Module  P0A1B-193  Drive Motor "A" Control Module  P0A1B-198  Drive Motor "A" Control Module  P0A1B-511  Drive Motor "A" Control Module  P0A1B-512  Drive Motor "A" Control Module  P0A1B-661  Drive Motor "A" Control Module  P0A1B-786  Drive Motor "A" Control Module  P0A1B-794  Drive Motor "A" Control Module  


DESCRIPTION

The MG ECU located in the inverter with converter assembly monitors its internal operation and it will set DTCs when it detects malfunctions.

DTC No. INF Code DTC Detection Condition Trouble Area
P0A1A 151 Run pulse signal cycle deviation or stop Inverter with converter assembly
155 A/D converter error
156 CPU ROM-RAM error
166 R/D converter NM stop error
658 ALU error
659 Communication error (from MG1 to MG2)
791 R/D converter communication error
P0A1B 163 IPM positive power source error
164 IPM negative power source error
192 A/D converter error
193 CPU ROM-RAM error
198 R/D converter NM stop error
511 Standard voltage for analog signal offset
512 Standard voltage for analog signal error
661 Communication error (from MG2 to MG1)
786 ALU error
794 R/D converter communication error

CAUTION / NOTICE / HINT

HINT:
·

If DTC P0A1A-151, P0A1A-155, P0A1A-658, P0A1A-659, P0A1A-791 DTC P0A1B-163, P0A1B-164, P0A1B-192, P0A1B-511, P0A1B-512, P0A1B-661, P0A1B-786 or P0A1B-794 is output, clear the DTCs, perform the following procedure, and check that the same DTC is not output after the repair.

(a)

Turn the power switch on (IG) and wait for 5 seconds or more.


·

If DTC P0A1A-156or P0A1B-193 is output, clear the DTCs, perform the following procedure, and check that the same DTC is not output after the repair.

(a)

Turn the power switch on (IG) and wait for 1 minute or more.


·

If DTC P0A1A-166 is output, clear the DTCs, perform the following procedure, and check that the same DTC is not output after the repair.

(a)

Turn the power switch on (READY).

(b)

With the vehicle stopped and the shift lever in P, depress the accelerator pedal and start the engine.

(c)

Depress the accelerator pedal and keep the engine running for 30 seconds or more.


·

If DTC P0A1B-198 is output, clear the DTCs, perform the following procedure, and check that the same DTC is not output after the repair.

(a)

Turn the power switch on (READY).

(b)

Drive the vehicle at 3 mph (5 km/h) or more for 30 seconds or more.




PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Check if DTCs are output.

Result:
Result Proceed to
None of the following DTCs are output. A
Any of the following DTCs are output. B


DTC No. Relevant Diagnosis
P0A1A-155, 156, 166, 658, 791 Generator Control Module
P0A1B-163, 164, 192, 193, 198, 511, 512, 661, 786, 794 Drive Motor "A" Control Module


e.

Turn the power switch off.



A

2.CHECK DTC OUTPUT (HYBRID CONTROL)

B

REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS

2.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Check if DTCs are output.

Result:
Result Proceed to
Only DTC P0A1A-151, P0A1A-659 or P324E-788 is output. A
Other than above. B



e.

Turn the power switch off.



A

3.CLEAR DTC

B

3.CLEAR DTC

NEXT

4.CHECK DTC OUTPUT (HYBRID CONTROL)
4.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch off and wait for 30 seconds or more.


c.

Turn the power switch on (IG) and wait for 5 seconds or more.


d.

Turn the power switch on (READY).


e.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


f.

Check if DTCs are output.

Result:
Result Proceed to
No DTCs are output (not including history DTCs). A
Only DTC P0A1A-151, P0A1A-659 or P324E-788 is output. B
Other than above. C



g.

Turn the power switch off.



A

REPLACE MG CONTROL COMPUTER

B

REPLACE POWER MODULE INTELLIGENT TRANSISTOR KIT AND MG CONTROL COMPUTER

C