Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › 2011.12–2014.12
RM2170E _51 Engine / Hybrid System _057004 HYBRID / BATTERY CONTROL _0277924 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0A09-265  DC / DC Converter Status Circuit Low Input  


DESCRIPTION

Refer to the description for DTC P0A08-264 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0A08-264).

DTC No. INF Code DTC Detection Condition Trouble Area
P0A09 265 Open or GND short in NODD signal circuit of DC/DC converter
·

Wire harness or connector

·

Inverter with converter assembly

·

Power management control ECU



WIRING DIAGRAM

Refer to the wiring diagram for DTC P0A08-264 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0A08-264).

CAUTION / NOTICE / HINT

CAUTION:
·

Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·

After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION).

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


HINT:
·

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

(a)

Turn the power switch on (IG) and wait for 10 seconds or more.


·

When the NODD signal line is short to ground, DC/DC converter control is prohibited and the auxiliary battery voltage will be approximately 12 V (or less).

·

When the transistor of the power management control ECU turns on, a signal is sent to the inverter to prohibit DC/DC converter control. The inverter with converter assembly sends a malfunction signal to the power management control ECU when the inverter side transistor is on.



PROCEDURE

1.CHECK CONNECTOR CONNECTION CONDITION (POWER MANAGEMENT CONTROL ECU CONNECTOR)

OK

2.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

NG

CONNECT SECURELY

2.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

OK

3.CHECK INVERTER WITH CONVERTER ASSEMBLY (INVERTER WITH CONVERTER ASSEMBLY POWER SOURCE CIRCUIT)

NG

CONNECT SECURELY

3.CHECK INVERTER WITH CONVERTER ASSEMBLY (INVERTER WITH CONVERTER ASSEMBLY POWER SOURCE CIRCUIT)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect connector A47 from the inverter with converter assembly.


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the power switch on (IG).


e.
A379052E06
1.479,0.188 1.896,0.438 0.417,0.25 0.583,1.51 1.125,0.948 true 0.073,0.104 0.385,0.302 0.313,0.198 10 false *a 1.573,0.24 1.99,0.469 0.417,0.229 10 false A47 0.375,1.521 0.844,1.729 0.469,0.208 10 false IGCT

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A47-1 (IGCT) - Body ground Power switch on (IG) 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Inverter with Converter Assembly)

NOTICE:
·

Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.


·

Turning the power switch on (IG) with the inverter with converter assembly connector connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



HINT:

As there might be an intermittent malfunction in the inverter with converter assembly power source circuit, inspect the following even if the measured voltage is as specified:

·

Installation condition of fuse(s) (before removing fuse(s)) (IGCT circuit)

·

Fuse condition (before and after removing fuse(s)) (IGCT circuit)

·

Connection condition of connectors (IGCT circuit)

·

Wire harness condition (IGCT circuit)

·

Wire harness condition (GND circuit)




f.

Turn the power switch off.


g.

Disconnect the cable from the negative (-) auxiliary battery terminal.


h.

Reconnect the A47 inverter with converter assembly connector.



OK

4.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY POWER SOURCE CIRCUIT)

4.CLEAR DTC
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / DTC.


d.

Read and record the DTCs and freeze frame data.


e.

Clear DTCs and freeze frame data.


f.

Turn the power switch off.



NEXT

5.CHECK DTC OUTPUT (HYBRID CONTROL)
5.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the intelligent tester to the DLC3.


b.

Depress the brake pedal and turn the ignition switch to ON (READY).

HINT:

Perform this step to check if the ignition switch can be turned ON (READY).



c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Check if DTCs are output.

Result:
Result Proceed to
Power switch cannot be turned ON (READY) and P0A09-265 is output. A
Power switch can be turned ON (READY) and P0A09-265 is not output. B



e.

Turn the power switch off.



A

6.CHECK HARNESS AND CONNECTOR (RESISTANCE VALUE OF NODD INSIDE POWER MANAGEMENT CONTROL ECU)

B

6.CHECK HARNESS AND CONNECTOR (RESISTANCE VALUE OF NODD INSIDE POWER MANAGEMENT CONTROL ECU)

OK

REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS

NG

7.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - POWER MANAGEMENT CONTROL ECU)
7.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - POWER MANAGEMENT CONTROL ECU)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect connector A47 from the inverter with converter assembly.


c.

Disconnect connector A38 from the power management control ECU.


d.
U183202E02
1.156,1.385 1.396,0.604 false 0.969,3.99 1.292,4.333 false 0.229,0.115 0.49,0.344 0.26,0.229 10 false *a 0.229,2.198 0.49,2.427 0.26,0.229 10 false *b 0.375,1.375 0.646,1.542 0.271,0.167 10 false A47 1.292,3.844 1.563,4.01 0.271,0.167 10 false A38 1.438,0.448 1.938,0.677 0.5,0.229 10 false NODD 1.323,4.271 1.823,4.5 0.5,0.229 10 false NODD

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A47-12 (NODD) - A38-21 (NODD) Power switch off Below 1 Ω
A47-12 (NODD) or A38-21 (NODD) - Body ground and other terminals Power switch off 10 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Inverter with Converter Assembly)
*b Rear view of wire harness connector
(to Power Management Control ECU)


e.

Connect the inverter with converter assembly connector.


f.

Connect the power management control ECU connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR