Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › 2011.12–2014.12
RM2170E _51 Engine / Hybrid System _057004 HYBRID / BATTERY CONTROL _0277924 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0A1A-200  Generator Control Module  P0A1A-792  Generator Control Module  P0A1A-793  Generator Control Module  


DESCRIPTION

The MG ECU located in the inverter with converter assembly monitors its internal operation and detects the following malfunctions.

DTC No. INF Code DTC Detection Condition Trouble Area
P0A1A 200 The difference between the resolver angle for control and estimated resolver angle exceeds the allowable value.
·

Inverter with converter assembly

·

Hybrid vehicle transaxle assembly

·

Wire harness or connector


792 Resolver REF signal cycle error
793 Resolver REF signal oscillation stop error

WIRING DIAGRAM

A220049E21
1.875,3.021 2.01,3.208 0.135,0.188 10 false 1 1.875,3.656 2.01,3.844 0.135,0.188 10 false 2 1.854,4.313 1.99,4.5 0.135,0.188 10 false 3 1.865,1.271 2,1.458 0.135,0.188 10 false 1 1.865,1.604 2,1.792 0.135,0.188 10 false 4 1.854,1.917 1.99,2.104 0.135,0.188 10 false 2 1.865,2.25 2,2.438 0.135,0.188 10 false 5 1.885,0.625 2.021,0.813 0.135,0.188 10 false 3 1.865,0.948 2,1.135 0.135,0.188 10 false 6 0.25,5.427 2.521,5.625 2.271,0.198 10 false Hybrid Vehicle Transaxle Assembly 0.708,5.042 2,5.24 1.292,0.198 10 false Generator Resolver 0.719,2.667 1.75,2.865 1.031,0.198 10 false Motor Resolver 1.479,4.333 1.875,4.521 0.396,0.188 10 false GCS 1.5,3.667 1.875,3.854 0.375,0.188 10 false GSN 1.5,3.01 1.865,3.198 0.365,0.188 10 false GRF 1.385,4.656 1.823,4.844 0.438,0.188 10 false GCSG 1.385,4 1.833,4.188 0.448,0.188 10 false GSNG 1.396,3.344 1.854,3.531 0.458,0.188 10 false GRFG 1.479,1.948 1.875,2.135 0.396,0.188 10 false MCS 1.49,1.281 1.865,1.469 0.375,0.188 10 false MSN 1.49,0.646 1.854,0.833 0.365,0.188 10 false MRF 1.375,2.26 1.813,2.448 0.438,0.188 10 false MCSG 1.375,1.615 1.823,1.802 0.448,0.188 10 false MSNG 1.385,0.938 1.844,1.125 0.458,0.188 10 false MRFG 4.292,5.198 4.583,5.354 0.292,0.156 10 false C28 4.292,5.354 7.063,5.563 2.771,0.208 10 false Inverter with Converter Assembly (MG ECU) 5.281,4.438 5.677,4.625 0.396,0.188 10 false GCS 5.281,3.771 5.656,3.958 0.375,0.188 10 false GSN 5.281,3.115 5.646,3.302 0.365,0.188 10 false GRF 5.281,4.75 5.719,4.938 0.438,0.188 10 false GCSG 5.281,4.104 5.729,4.292 0.448,0.188 10 false GSNG 5.281,3.448 5.74,3.635 0.458,0.188 10 false GRFG 5.281,2.01 5.677,2.198 0.396,0.188 10 false MCS 5.281,1.344 5.656,1.531 0.375,0.188 10 false MSN 5.281,0.698 5.646,0.885 0.365,0.188 10 false MRF 5.281,2.333 5.719,2.521 0.438,0.188 10 false MCSG 5.281,1.688 5.729,1.875 0.448,0.188 10 false MSNG 5.281,1.021 5.74,1.208 0.458,0.188 10 false MRFG 5.281,2.688 5.719,2.875 0.438,0.188 10 false DRN6 5.021,3 5.198,3.188 0.177,0.188 10 false 11 5.073,3.667 5.208,3.854 0.135,0.188 10 false 7 5.073,3.979 5.208,4.167 0.135,0.188 10 false 8 5.073,4.635 5.208,4.823 0.135,0.188 10 false 9 0.719,2.5 0.99,2.688 0.271,0.188 10 false C26 0.708,4.896 0.99,5.083 0.281,0.188 10 false C24 1.865,3.313 2,3.5 0.135,0.188 10 false 5 1.865,3.979 2,4.167 0.135,0.188 10 false 6 1.875,4.646 2.01,4.833 0.135,0.188 10 false 7 5.083,0.604 5.219,0.792 0.135,0.188 10 false 1 5.083,0.927 5.177,1.115 0.094,0.188 10 false 2 5.083,1.26 5.219,1.448 0.135,0.188 10 false 3 5.083,1.594 5.188,1.781 0.104,0.188 10 false 4 5.083,2.24 5.177,2.427 0.094,0.188 10 false 5 5.083,1.906 5.219,2.094 0.135,0.188 10 false 6 5,3.323 5.198,3.51 0.198,0.188 10 false 12 5,4.313 5.198,4.5 0.198,0.188 10 false 10 5.031,2.594 5.229,2.781 0.198,0.188 10 false 13

CAUTION / NOTICE / HINT

CAUTION:
·

Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·

After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION).

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Turn the power switch on (IG) and wait for 5 seconds or more.

2.

Turn the power switch on (READY) with the shift lever in P and wait for 5 seconds or more.

3.

Depress the accelerator pedal of the vehicle with the engine stopped and the shift lever in P to start the engine.

4.

Keep the engine running for 5 seconds or more.

5.

Drive the vehicle forward with the shift lever in D for 5 m or more.

6.

Drive the vehicle backward with the shift lever in R for 5 m or more.



PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / DTC.


d.

Check if DTCs are output.

Result:
Result Proceed to
Only P0A1A-200, 792 or 793 is output, or DTCs other than the ones in the table below are also output. A
Any of the DTCs are also output. B


DTC No. Relevant Diagnosis
P0A3F-243 Drive Motor "A" Position Sensor Circuit
P0A4B-253 Generator Position Sensor Circuit
P0A4C-513 Generator Position Sensor Circuit Range / Performance
P0A4D-255 Generator Position Sensor Circuit Low


e.

Turn the power switch off.



A

2.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

B

2.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

OK

3.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - GENERATOR RESOLVER)

NG

CONNECT SECURELY

3.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - GENERATOR RESOLVER)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect connector C28 from the inverter with converter assembly.


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the power switch on (IG).


e.
U158896E03
1.635,1.896 0.906,2.719 false 1.49,1.885 0.823,2.313 false 1.479,1.74 0.865,1.906 false 1.969,1.729 2.5,1.771 false 1.813,1.708 2.521,1.417 false 1.646,1.729 2.5,1.031 false 0.156,0.146 0.458,0.354 0.302,0.208 10 false *a 0.521,1.833 0.896,2.031 0.375,0.198 10 false GSN 0.479,2.26 0.875,2.458 0.396,0.198 10 false GRF 0.479,2.688 1,2.885 0.521,0.198 10 false GRFG 2.552,0.896 3,1.094 0.448,0.198 10 false GSNG 2.583,1.313 3.052,1.51 0.469,0.198 10 false GCSG 2.563,1.708 2.958,1.906 0.396,0.198 10 false GCS 1.76,2.76 2.281,3.115 0.521,0.354 10 false C28

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C28-11 (GRF) - Body ground Power switch on (IG) Below 1 V
C28-12 (GRFG) - Body ground Power switch on (IG) Below 1 V
C28-7 (GSN) - Body ground Power switch on (IG) Below 1 V
C28-8 (GSNG) - Body ground Power switch on (IG) Below 1 V
C28-10 (GCS) - Body ground Power switch on (IG) Below 1 V
C28-9 (GCSG) - Body ground Power switch on (IG) Below 1 V


Text in Illustration
*a Front view of wire harness connector
(to Inverter with Converter Assembly)

NOTICE:

Turning the power switch on (IG) with the low voltage connector of the inverter with converter assembly disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



f.

Turn the power switch off.


g.

Disconnect the cable from the negative (-) auxiliary battery terminal.


h.

Connect the inverter with converter assembly connector.



OK

4.CHECK GENERATOR RESOLVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK GENERATOR RESOLVER
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect connector C28 from the inverter with converter assembly.


c.
U158896E04
1.635,1.896 1.125,2.792 false 1.458,1.906 0.688,2.448 false 1.479,1.698 0.646,1.708 false 1.99,1.74 2.792,1.729 false 1.833,1.76 2.74,2.219 false 1.615,1.75 0.646,2.073 false 1.813,1.906 2.573,2.729 false 1.479,1.417 0.76,0.854 false 1.646,1.396 1.229,0.448 false 1.479,1.563 0.677,1.281 false 1.677,1.563 2.24,0.5 false 1.823,1.563 2.635,0.813 false 1.979,1.573 2.771,1.281 false 0.156,0.146 0.458,0.354 0.302,0.208 10 false *a 0.313,1.635 0.688,1.833 0.375,0.198 10 false GSN 0.49,2.49 0.885,2.688 0.396,0.198 10 false GRF 0.885,2.813 1.406,3.01 0.521,0.198 10 false GRFG 0.219,2.01 0.667,2.208 0.448,0.198 10 false GSNG 2.792,2.188 3.26,2.385 0.469,0.198 10 false GCSG 2.833,1.646 3.229,1.844 0.396,0.198 10 false GCS 1.76,2.76 2.281,3.115 0.521,0.354 10 false C28 2.469,2.771 3.135,3.021 0.667,0.25 10 false DRN6 0.458,0.75 0.833,0.948 0.375,0.198 10 false MRF 0.813,0.313 1.5,0.573 0.688,0.26 10 false MRFG 0.333,1.167 0.708,1.365 0.375,0.198 10 false MSN 2.25,0.323 2.938,0.583 0.688,0.26 10 false MSNG 2.667,0.698 3.354,0.958 0.688,0.26 10 false MCSG 2.813,1.167 3.208,1.365 0.396,0.198 10 false MCS

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Switch Condition Specified Condition
C28-11 (GRF) - C28-12 (GRFG) Power switch off 9.5 to 15.5 Ω
C28-7 (GSN) - C28-8 (GSNG) Power switch off 15.0 to 27.0 Ω
C28-10 (GCS) - C28-9 (GCSG) Power switch off 14.0 to 26.0 Ω


Standard Resistance (Check for Short):
Tester Connection Switch Condition Specified Condition
C28-11 (GRF) or C28-12 (GRFG) - C28-10 (GCS) or C28-9 (GCSG) Ignition switch off 1 MΩ or higher
C28-11 (GRF) or C28-12 (GRFG) - C28-7 (GSN) or C28-8 (GSNG) Ignition switch off 1 MΩ or higher
C28-11 (GRF) or C28-12 (GRFG) - C28-1 (MRF) or C28-2 (MRFG) Ignition switch off 1 MΩ or higher
C28-11 (GRF) or C28-12 (GRFG) - C28-6 (MCS) or C28-5 (MCSG) Ignition switch off 1 MΩ or higher
C28-11 (GRF) or C28-12 (GRFG) - C28-3 (MSN) or C28-4 (MSNG) Ignition switch off 1 MΩ or higher
C28-11 (GRF) or C28-12 (GRFG) - C28-13 (DRN6) Ignition switch off 1 MΩ or higher
C28-11 (GRF) or C28-12 (GRFG) - Body ground Ignition switch off 1 MΩ or higher
C28-10 (GCS) or C28-9 (GCSG) - C28-7 (GSN) or C28-8 (GSNG) Ignition switch off 1 MΩ or higher
C28-10 (GCS) or C28-9 (GCSG) - C28-1 (MRF) or C28-2 (MRFG) Ignition switch off 1 MΩ or higher
C28-10 (GCS) or C28-9 (GCSG) - C28-6 (MCS) or C28-5 (MCSG) Ignition switch off 1 MΩ or higher
C28-10 (GCS) or C28-9 (GCSG) - C28-3 (MSN) or C28-4 (MSNG) Ignition switch off 1 MΩ or higher
C28-10 (GCS) or C28-9 (GCSG) - C28-13 (DRN6) Ignition switch off 1 MΩ or higher
C28-10 (GCS) or C28-9 (GCSG) - Body ground Ignition switch off 1 MΩ or higher
C28-7 (GSN) or C28-8 (GSNG) - C28-1 (MRF) or C28-2 (MRFG) Ignition switch off 1 MΩ or higher
C28-7 (GSN) or C28-8 (GSNG) - C28-6 (MCS) or C28-5 (MCSG) Ignition switch off 1 MΩ or higher
C28-7 (GSN) or C28-8 (GSNG) - C28-3 (MSN) or C28-4 (MSNG) Ignition switch off 1 MΩ or higher
C28-7 (GSN) or C28-8 (GSNG) - C28-13 (DRN6) Ignition switch off 1 MΩ or higher
C28-7 (GSN) or C28-8 (GSNG) - Body ground Ignition switch off 1 MΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Inverter with Converter Assembly)


d.

Connect the inverter with converter assembly connector.



OK

5.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - MOTOR RESOLVER)

NG

11.CHECK CONNECTOR CONNECTION CONDITION (GENERATOR RESOLVER CONNECTOR)
5.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - MOTOR RESOLVER)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect connector C28 from the inverter with converter assembly.


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the power switch on (IG).


e.
U158897E03
1.49,1.583 0.75,1.615 false 1.49,1.406 0.948,1.063 false 1.646,1.396 1.448,0.563 false 1.677,1.573 2.271,0.594 false 1.802,1.563 2.479,1.021 false 1.979,1.583 2.51,1.677 false 0.177,0.115 0.51,0.354 0.333,0.24 10 false *a 1.583,2.833 2.083,3.052 0.5,0.219 10 false C28 0.385,1.552 0.813,1.781 0.427,0.229 10 false MSN 2.323,0.417 2.823,0.646 0.5,0.229 10 false MSNG 2.573,0.917 3.073,1.146 0.5,0.229 10 false MCSG 2.563,1.594 3.063,1.823 0.5,0.229 10 false MCS 0.635,0.927 1.063,1.156 0.427,0.229 10 false MRF 1.125,0.375 1.552,0.604 0.427,0.229 10 false MRFG

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C28-1 (MRF) - Body ground Power switch on (IG) Below 1 V
C28-2 (MRFG) - Body ground Power switch on (IG) Below 1 V
C28-3 (MSN) - Body ground Power switch on (IG) Below 1 V
C28-4 (MSNG) - Body ground Power switch on (IG) Below 1 V
C28-6 (MCS) - Body ground Power switch on (IG) Below 1 V
C28-5 (MCSG) - Body ground Power switch on (IG) Below 1 V


Text in Illustration
*a Front view of wire harness connector
(to Inverter with Converter Assembly)

NOTICE:

Turning the power switch on (IG) with the low voltage connector of the inverter with converter assembly disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



f.

Turn the power switch off.


g.

Disconnect the cable from the negative (-) auxiliary battery terminal.


h.

Connect the inverter with converter assembly connector.



OK

6.CHECK MOTOR RESOLVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK MOTOR RESOLVER
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect connector C28 from the inverter with converter assembly.


c.
U158896E04
1.635,1.896 1.125,2.792 false 1.458,1.906 0.688,2.448 false 1.479,1.698 0.646,1.708 false 1.99,1.74 2.792,1.729 false 1.833,1.76 2.74,2.219 false 1.615,1.75 0.646,2.073 false 1.813,1.906 2.573,2.729 false 1.479,1.417 0.76,0.854 false 1.646,1.396 1.229,0.448 false 1.479,1.563 0.677,1.281 false 1.677,1.563 2.24,0.5 false 1.823,1.563 2.635,0.813 false 1.979,1.573 2.771,1.281 false 0.156,0.146 0.458,0.354 0.302,0.208 10 false *a 0.313,1.635 0.688,1.833 0.375,0.198 10 false GSN 0.49,2.49 0.885,2.688 0.396,0.198 10 false GRF 0.885,2.813 1.406,3.01 0.521,0.198 10 false GRFG 0.219,2.01 0.667,2.208 0.448,0.198 10 false GSNG 2.792,2.188 3.26,2.385 0.469,0.198 10 false GCSG 2.833,1.646 3.229,1.844 0.396,0.198 10 false GCS 1.76,2.76 2.281,3.115 0.521,0.354 10 false C28 2.469,2.771 3.135,3.021 0.667,0.25 10 false DRN6 0.458,0.75 0.833,0.948 0.375,0.198 10 false MRF 0.813,0.313 1.5,0.573 0.688,0.26 10 false MRFG 0.333,1.167 0.708,1.365 0.375,0.198 10 false MSN 2.25,0.323 2.938,0.583 0.688,0.26 10 false MSNG 2.667,0.698 3.354,0.958 0.688,0.26 10 false MCSG 2.813,1.167 3.208,1.365 0.396,0.198 10 false MCS

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Switch Condition Specified Condition
C28-1 (MRF) - C28-2 (MRFG) Power switch off 9.5 to 15.5 Ω
C28-3 (MSN) - C28-4 (MSNG) Power switch off 15.0 to 27.0 Ω
C28-6 (MCS) - C28-5 (MCSG) Power switch off 14.0 to 26.0 Ω


Standard Resistance (Check for Short):
Tester Connection Switch Condition Specified Condition
C28-1 (MRF) or C28-2 (MRFG) - C28-6 (MCS) or C28-5 (MCSG) Ignition switch off 1 MΩ or higher
C28-1 (MRF) or C28-2 (MRFG) - C28-3 (MSN) or C28-4 (MSNG) Ignition switch off 1 MΩ or higher
C28-1 (MRF) or C28-2 (MRFG) - C28-11 (GRF) or C28-12 (GRFG) Ignition switch off 1 MΩ or higher
C28-1 (MRF) or C28-2 (MRFG) - C28-10 (GCS) or C28-9 (GCSG) Ignition switch off 1 MΩ or higher
C28-1 (MRF) or C28-2 (MRFG) - C28-7 (GSN) or C28-8 (GSNG) Ignition switch off 1 MΩ or higher
C28-1 (MRF) or C28-2 (MRFG) - C28-13 (DRN6) Ignition switch off 1 MΩ or higher
C28-1 (MRF) or C28-2 (MRFG) - Body ground Ignition switch off 1 MΩ or higher
C28-6 (MCS) or C28-5 (MCSG) - C28-3 (MSN) or C28-4 (MSNG) Ignition switch off 1 MΩ or higher
C28-6 (MCS) or C28-5 (MCSG) - C28-11 (GRF) or C28-12 (GRFG) Ignition switch off 1 MΩ or higher
C28-6 (MCS) or C28-5 (MCSG) - C28-10 (GCS) or C28-9 (GCSG) Ignition switch off 1 MΩ or higher
C28-6 (MCS) or C28-5 (MCSG) - C28-7 (GSN) or C28-8 (GSNG) Ignition switch off 1 MΩ or higher
C28-6 (MCS) or C28-5 (MCSG) - C28-13 (DRN6) Ignition switch off 1 MΩ or higher
C28-6 (MCS) or C28-5 (MCSG) - Body ground Ignition switch off 1 MΩ or higher
C28-3 (MSN) or C28-4 (MSNG) - C28-11 (GRF) or C28-12 (GRFG) Ignition switch off 1 MΩ or higher
C28-3 (MSN) or C28-4 (MSNG) - C28-10 (GCS) or C28-9 (GCSG) Ignition switch off 1 MΩ or higher
C28-3 (MSN) or C28-4 (MSNG) - C28-7 (GSN) or C28-8 (GSNG) Ignition switch off 1 MΩ or higher
C28-3 (MSN) or C28-4 (MSNG) - C28-13 (DRN6) Ignition switch off 1 MΩ or higher
C28-3 (MSN) or C28-4 (MSNG) - Body ground Ignition switch off 1 MΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Inverter with Converter Assembly)


d.

Connect the inverter with converter assembly connector.



OK

7.CHECK CONNECTOR CONNECTION CONDITION (GENERATOR RESOLVER CONNECTOR)

NG

13.CHECK CONNECTOR CONNECTION CONDITION (MOTOR RESOLVER CONNECTOR)
7.CHECK CONNECTOR CONNECTION CONDITION (GENERATOR RESOLVER CONNECTOR)
a.
A267571

Check the connection of the generator resolver connector.

OK:

The connector is connected securely and there are no contact problems.




OK

8.CHECK CONNECTOR CONNECTION CONDITION (MOTOR RESOLVER CONNECTOR)

NG

CONNECT SECURELY

8.CHECK CONNECTOR CONNECTION CONDITION (MOTOR RESOLVER CONNECTOR)
a.
A267572

Check the connection of the motor resolver connector.

OK:

The connector is connected securely and there are no contact problems.




OK

9.CHECK FOR INTERMITTENT PROBLEMS

NG

CONNECT SECURELY

9.CHECK FOR INTERMITTENT PROBLEMS
a.

Check for intermittent problems.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>CHECK FOR INTERMITTENT PROBLEMS

i.

Check the connection and terminal contact pressure of the connectors and wire harnesses between the inverter with converter assembly and the resolver.




OK

10.SIMULATION TEST

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

10.SIMULATION TEST
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG) and wait for 5 seconds or more.


c.

Turn the power switch on (READY) with the shift lever in P and wait for 5 seconds or more.


d.

Depress the accelerator pedal of the vehicle with the engine stopped and the shift lever in P to start the engine.


e.

Keep the engine running for 5 seconds or more.


f.

Drive the vehicle forward with the shift lever in D for 5 m or more.


g.

Drive the vehicle backward with the shift lever in R for 5 m or more.


h.

Enter the following menus: Powertrain / Hybrid Control / DTC.


i.

Check if DTCs are output.

Result:
Result Proceed to
P0A1A-200, P0A1A-792 or P0A1A-793 is output. A
P0A1A-200, P0A1A-792 and P0A1A-793 are not output. B


HINT:

If the connector engagement check and cleaning caused the condition to return to normal, DTCs will not be output.



j.

Turn the power switch off.



A

REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS

B

END

11.CHECK CONNECTOR CONNECTION CONDITION (GENERATOR RESOLVER CONNECTOR)
a.
A267571

Check the connection of the generator resolver connector.

OK:

The connector is connected securely and there are no contact problems.




OK

12.INSPECT HYBRID VEHICLE TRANSAXLE ASSEMBLY (GENERATOR RESOLVER)

NG

CONNECT SECURELY

12.INSPECT HYBRID VEHICLE TRANSAXLE ASSEMBLY (GENERATOR RESOLVER)
a.
A267571N01
0.25,0.063 0.625,0.323 0.375,0.26 0.292,0.104 0.615,0.323 0.323,0.219 10 false C24

Disconnect the C24 generator resolver connector.


b.
A397757C06
1.448,0.115 1.885,0.344 0.438,0.229 0.885,0.677 1.531,1 true 1.188,1.823 1.625,1.313 true 1.885,1 2.323,0.49 true 2.063,1.042 2.573,0.813 true 2.083,1.292 2.531,1.573 true 1.875,1.313 2.229,1.813 true 0.375,0.115 0.688,0.271 0.313,0.156 10 false *a 1.531,0.146 2.146,0.344 0.615,0.198 10 false C24 2.635,0.719 3.094,0.917 0.458,0.198 10 false GRF 2.573,1.521 3.031,1.719 0.458,0.198 10 false GRFG 2.375,0.375 2.833,0.573 0.458,0.198 10 false GSN 2.073,1.854 2.531,2.052 0.458,0.198 10 false GSNG 0.563,0.563 1.021,0.76 0.458,0.198 10 false GCS 0.958,1.854 1.417,2.052 0.458,0.198 10 false GCSG
*a Component without harness connected
(Generator Resolver (Hybrid Vehicle Transaxle Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C24-1 (GRF) - C24-5 (GRFG) Power switch off 9.5 to 15.5 Ω
C24-2 (GSN) - C24-6 (GSNG) Power switch off 15.0 to 27.0 Ω
C24-3 (GCS) - C24-7 (GCSG) Power switch off 14.0 to 26.0 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
C24-1 (GRF) - Body ground and other terminals (except 5 (GRFG)) Power switch off 1 MΩ or higher
C24-5 (GRFG) - Body ground and other terminals (except 1 (GRF)) Power switch off 1 MΩ or higher
C24-2 (GSN) - Body ground and other terminals (except 6 (GSNG)) Power switch off 1 MΩ or higher
C24-6 (GSNG) - Body ground and other terminals (except 2 (GSN)) Power switch off 1 MΩ or higher
C24-3 (GCS) - Body ground and other terminals (except 7 (GCSG)) Power switch off 1 MΩ or higher
C24-7 (GCSG) - Body ground and other terminals (except 3 (GCS)) Power switch off 1 MΩ or higher


HINT:

The generator resolver is not available separately. If it requires replacement, replace the hybrid vehicle transaxle assembly.



c.

Reconnect the C24 generator resolver connector.



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG

13.CHECK CONNECTOR CONNECTION CONDITION (MOTOR RESOLVER CONNECTOR)
a.
A267572

Check the connection of the motor resolver connector.

OK:

The connector is connected securely and there are no contact problems.




OK

14.INSPECT HYBRID VEHICLE TRANSAXLE ASSEMBLY (MOTOR RESOLVER)

NG

CONNECT SECURELY

14.INSPECT HYBRID VEHICLE TRANSAXLE ASSEMBLY (MOTOR RESOLVER)
a.
A267572N02
1.604,2.646 2.01,2.938 0.406,0.292 1.646,2.719 2,2.917 0.354,0.198 10 true C26

Disconnect the C26 motor resolver connector.


b.
A397815C03
1.448,0.167 1.865,0.417 0.417,0.25 0.406,1.667 1.083,1.177 true 0.948,1.677 1.385,1.208 true 1.458,1.677 1.594,1.198 true 2.854,1.625 2.323,1.188 true 2.458,1.615 2.063,1.208 true 2.031,1.656 1.833,1.198 true 1.906,1.688 2.365,1.885 0.458,0.198 10 false MRF 0.167,1.698 0.625,1.896 0.458,0.198 10 false MRFG 2.74,1.667 3.198,1.865 0.458,0.198 10 false MSN 1.26,1.698 1.719,1.896 0.458,0.198 10 false MSNG 2.323,1.667 2.781,1.865 0.458,0.198 10 false MCS 0.719,1.698 1.177,1.896 0.458,0.198 10 false MCSG 0.396,0.281 0.708,0.438 0.313,0.156 10 false *a 1.5,0.219 2.115,0.417 0.615,0.198 10 false C26
*a Component without harness connected
(Motor Resolver (Hybrid Vehicle Transaxle Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C26-3 (MRF) - C26-6 (MRFG) Power switch off 9.5 to 15.5 Ω
C26-1 (MSN) - C26-4 (MSNG) Power switch off 15.0 to 27.0 Ω
C26-2 (MCS) - C26-5 (MCSG) Power switch off 14.0 to 26.0 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
C26-3 (MRF) - Body ground and other terminals (except 6 (MRFG)) Power switch off 1 MΩ or higher
C26-6 (MRFG) - Body ground and other terminals (except 3 (MRF)) Power switch off 1 MΩ or higher
C26-1 (MSN) - Body ground and other terminals (except 4 (MSNG)) Power switch off 1 MΩ or higher
C26-4 (MSNG) - Body ground and other terminals (except 1 (MSN)) Power switch off 1 MΩ or higher
C26-2 (MCS) - Body ground and other terminals (except 5 (MCSG)) Power switch off 1 MΩ or higher
C26-5 (MCSG) - Body ground and other terminals (except 2 (MCS)) Power switch off 1 MΩ or higher


HINT:

The motor resolver is not available separately. If it requires replacement, replace the hybrid vehicle transaxle assembly.



c.

Reconnect the C26 motor resolver connector.



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG