Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › 2011.12–2014.12
RM2170E _51 Engine / Hybrid System _057004 HYBRID / BATTERY CONTROL _0277924 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P2120-152  Throttle / Pedal Position Sensor / Switch "D" Circuit  P2121-106  Throttle / Pedal Position Sensor / Switch "D" Circuit Range / Performance  P2122-104  Throttle / Pedal Position Sensor / Switch "D" Circuit Low Input  P2123-105  Throttle / Pedal Position Sensor / Switch "D" Circuit High Input  P2125-153  Throttle / Pedal Position Sensor / Switch "E" Circuit  P2126-109  Throttle / Pedal Position Sensor / Switch "E" Circuit Range / Performance  P2127-107  Throttle / Pedal Position Sensor / Switch "E" Circuit Low Input  P2128-108  Throttle / Pedal Position Sensor / Switch "E" Circuit High Input  P2138-110  Throttle / Pedal Position Sensor / Switch "D" / "E" Voltage Correlation  P2138-154  Throttle / Pedal Position Sensor / Switch "D" / "E" Voltage Correlation  


DESCRIPTION

The accelerator pedal position sensor is mounted on the accelerator pedal to detect how much the pedal is depressed. This is a non-contact sensor with hall elements. There are 2 outputs from the sensor. One is used to detect the accelerator pedal position and the other is used as a confirmation to allow the detection of a malfunction in the sensor itself. Voltage is output from the accelerator pedal position sensor to terminals VPA1 and VPA2 of the power management control ECU. This voltage varies from 0 to 5 V in accordance with the accelerator pedal position. Terminal VPA2 is primarily used to detect a malfunction in the sensor itself. The power management control ECU determines the current accelerator pedal position and controls the hybrid control system based on signals received by terminals VPA1 and VPA2.

A222964E59
0.76,2.708 0.76,3.427 0.76,3.427 0.854,3.427 false 0.76,1.615 0.76,0.75 0.76,0.75 0.865,0.75 false 0.74,2.01 0.219,0.385 0.219,0.385 0.302,0.385 false 0.75,2.354 0.198,3.813 0.198,3.813 0.281,3.813 false 0.896,0.667 1.406,0.833 0.51,0.167 10 false Magnet 0.333,0.313 1.188,0.479 0.854,0.167 10 false Hall Element 0.333,3.74 1.188,3.906 0.854,0.167 10 false Hall Element 0.875,3.354 1.385,3.521 0.51,0.167 10 false Magnet 1.74,3.542 3.021,3.938 1.281,0.396 10 false Power Management Control ECU 2.865,1.771 4.083,2.313 1.219,0.542 10 false Accelerator Pedal Position Sensor Output Voltage (V) 4.5,0.708 6.719,0.885 2.219,0.177 10 false Accelerator Pedal Turning Angle (°) 4.396,4.094 6.708,4.271 2.313,0.177 10 false *1: Accelerator Pedal Fully Released 4.396,4.385 6.781,4.563 2.385,0.177 10 false *2: Accelerator Pedal Fully Depressed 0.198,4.063 1.323,4.396 1.125,0.333 10 false Accelerator Pedal Sensor Assembly 2.146,1.094 2.396,1.26 0.25,0.167 10 false 5 V 4.229,1.01 4.323,1.177 0.094,0.167 10 false 5 4.229,2.396 4.323,2.563 0.094,0.167 10 false 0 3.938,1.271 4.323,1.438 0.385,0.167 10 false 3.988 3.938,1.469 4.323,1.635 0.385,0.167 10 false 3.188 4.104,1.938 4.323,2.104 0.219,0.167 10 false 1.6 6.865,1.115 7.156,1.281 0.292,0.167 10 false 4.55 6.865,1.365 7.156,1.531 0.292,0.167 10 false 3.75 6.656,2.5 6.833,2.667 0.177,0.167 10 false 20 4.25,2.823 4.427,2.99 0.177,0.167 10 false *1 6.052,2.823 6.229,2.99 0.177,0.167 10 false *2 5.104,2.5 5.427,2.667 0.323,0.167 10 false 13.1 4.104,2.156 4.323,2.323 0.219,0.167 10 false 0.8 2.51,1.948 2.76,2.115 0.25,0.167 10 false 5 V 2.198,1.677 2.406,1.844 0.208,0.167 10 false AD 2.354,2.552 2.563,2.719 0.208,0.167 10 false AD

DTC No. INF Code DTC Detection Condition Trouble Area
P2120 152 Main sensor circuit wiring malfunction or level is not stable
·

Wire harness or connector

·

Accelerator pedal sensor assembly

·

Power management control ECU


P2121 106 Internal error of the main sensor
P2122 104 Open or short to GND in the main sensor circuit
P2123 105 Short to +B in the main sensor circuit
P2125 153 Sub sensor circuit wiring malfunction or level is not stable
P2126 109 Internal error of the sub sensor
P2127 107 Open or short to GND in the sub sensor circuit
P2128 108 Short to +B in the sub sensor circuit
P2138 110 Difference between the main sensor value and sub sensor value is large.
154 Main or sub sensor circuit wiring malfunction

WIRING DIAGRAM

A169668E67
1.792,0.531 2.188,0.667 0.396,0.135 10 false VCP1 1.781,1.844 2.177,1.979 0.396,0.135 10 false VCP2 1.802,0.958 2.188,1.094 0.385,0.135 10 false VPA1 1.813,2.271 2.208,2.406 0.396,0.135 10 false VPA2 1.885,1.396 2.188,1.531 0.302,0.135 10 false EP1 0.594,3.031 0.948,3.229 0.354,0.198 10 false A31 1.875,2.719 2.26,2.854 0.385,0.135 10 false EP2 5.323,0.427 5.719,0.563 0.396,0.135 10 false VCP1 5.073,0.427 5.25,0.563 0.177,0.135 10 false 18 5.073,0.875 5.25,1.01 0.177,0.135 10 false 26 5.063,1.313 5.25,1.448 0.188,0.135 10 false 34 5.073,1.76 5.25,1.896 0.177,0.135 10 false 19 5.073,2.188 5.25,2.323 0.177,0.135 10 false 27 5.073,2.635 5.281,2.802 0.208,0.167 10 false 35 5.323,1.76 5.719,1.896 0.396,0.135 10 false VCP2 5.323,0.875 5.708,1.01 0.385,0.135 10 false VPA1 5.323,2.188 5.719,2.323 0.396,0.135 10 false VPA2 5.323,1.313 5.625,1.448 0.302,0.135 10 false EP1 5.323,2.635 5.625,2.771 0.302,0.135 10 false EP2 0.594,3.177 2.833,3.365 2.24,0.188 10 false Accelerator Pedal Sensor Assembly 4.969,3.042 5.375,3.219 0.406,0.177 10 false A39 4.958,3.188 7.104,3.396 2.146,0.208 10 false Power Management Control ECU 2.26,0.417 2.375,0.563 0.115,0.146 10 false 4 2.26,0.854 2.375,1 0.115,0.146 10 false 6 2.26,1.302 2.375,1.448 0.115,0.146 10 false 5 2.26,1.75 2.375,1.896 0.115,0.146 10 false 1 2.26,2.198 2.375,2.344 0.115,0.146 10 false 3 2.26,2.635 2.375,2.781 0.115,0.146 10 false 2 6.104,1.719 6.344,1.865 0.24,0.146 10 false 5 V 6.104,0.375 6.344,0.521 0.24,0.146 10 false 5 V 5.792,1.125 6.26,1.458 0.469,0.333 10 false 39 kΩ+/-5 % 5.823,2.448 6.271,2.979 0.448,0.531 10 false 39 kΩ+/-5 %

CAUTION / NOTICE / HINT

HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Wait for approximately 10 seconds with the power switch on (READY) and the shift lever in P, then fully depress and release the accelerator pedal several times.



PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (ACCEL PEDAL POS #1, ACCEL PEDAL POS #2)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Data List / Accel Pedal Pos #1, Accel Pedal Pos #2.


d.

Read the Data List.

Result:
Tester Display Accelerator Pedal Condition Specified Condition
Accel Pedal Pos #1 Not depressed 10 to 22 %
Fully depressed 52 to 90 %
Not depressed → Fully depressed → Not depressed (Accelerator pedal should be operated slowly) Value changes progressively
Accel Pedal Pos #2 Not depressed 24 to 40 %
Fully depressed 68 to 99 %
Not depressed → Fully depressed → Not depressed (Accelerator pedal should be operated slowly) Value changes progressively



e.

Turn the power switch off.



OK

NG

2.CHECK CONNECTOR CONNECTION CONDITION (ACCELERATOR PEDAL SENSOR ASSEMBLY CONNECTOR)
2.CHECK CONNECTOR CONNECTION CONDITION (ACCELERATOR PEDAL SENSOR ASSEMBLY CONNECTOR)
a.
A389821E01
0.073,0.052 0.385,0.25 0.313,0.198 10 false *A 0.104,2.281 0.417,2.479 0.313,0.198 10 false *B

Check the connection of the accelerator pedal sensor assembly connector.

Text in Illustration
*A for LHD
*B for RHD

OK:

The connector is connected securely and there are no contact problems.




OK

3.CHECK CONNECTOR CONNECTION CONDITION (POWER MANAGEMENT CONTROL ECU CONNECTOR)

NG

CONNECT SECURELY

3.CHECK CONNECTOR CONNECTION CONDITION (POWER MANAGEMENT CONTROL ECU CONNECTOR)

OK

4.CHECK POWER MANAGEMENT CONTROL ECU (CHECK VOLTAGE)

NG

CONNECT SECURELY

4.CHECK POWER MANAGEMENT CONTROL ECU (CHECK VOLTAGE)
a.

Disconnect connector A31 from the accelerator pedal sensor assembly.


b.

Turn the power switch on (IG).


c.
U183236E01
0.73,1.828 1.162,1.983 0.433,0.155 10 VCP2 1.304,1.828 1.737,1.983 0.433,0.155 10 EP2 1.841,1.828 2.273,1.983 0.433,0.155 10 VCP1 2.449,1.828 2.753,1.983 0.304,0.155 10 EP1 1.338,1.144 0.946,1.828 false 1.495,1.144 1.456,1.844 false 1.812,1.144 2.055,1.828 false 1.952,1.146 2.597,1.828 false 2.876,1.031 3.141,1.212 0.264,0.181 10 A31 0.19,0.1 0.364,0.261 0.174,0.161 10 *a

Measure the voltage according to the value(s) in the table below.

Standard Voltage :
Tester Connection Switch Condition Specified Condition
A31-4 (VCP1) - A31-5 (EP1) Power switch on (IG) 4.5 to 5.5 V
A31-1 (VCP2) - A31-2 (EP2) Power switch on (IG) 4.5 to 5.5 V



Text in Illustration
*a Front view of wire harness connector
(to Accelerator Pedal Sensor Assembly)

d.

Turn the power switch off.


e.

Connect the accelerator pedal sensor assembly connector.



OK

5.CHECK POWER MANAGEMENT CONTROL ECU (CHECK RESISTANCE)

NG

7.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - ACCELERATOR PEDAL SENSOR)
5.CHECK POWER MANAGEMENT CONTROL ECU (CHECK RESISTANCE)
a.

Disconnect connector A31 from the accelerator pedal sensor assembly.


b.
U183237E01
1.322,1.852 1.755,2.006 0.433,0.155 10 VPA2 0.786,1.852 1.218,2.006 0.433,0.155 10 EP2 2.372,1.852 2.804,2.006 0.433,0.155 10 VPA1 1.93,1.852 2.234,2.006 0.304,0.155 10 EP1 1.492,1.15 0.954,1.851 false 1.948,1.152 2.095,1.835 false 2.873,1.037 3.137,1.219 0.264,0.181 10 A31 0.187,0.106 0.361,0.267 0.174,0.161 10 *a 1.649,1.146 1.552,1.852 false 2.132,1.167 2.585,1.852 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A31-6 (VPA1) - A31-5 (EP1) Power switch off 28.00 to 41.61 kΩ
A31-3 (VPA2) - A31-2 (EP2) Power switch off 28.00 to 41.61 kΩ



Text in Illustration
*a Front view of wire harness connector
(to Accelerator Pedal Sensor Assembly)

c.

Connect the accelerator pedal sensor assembly connector.



OK

NG

6.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - ACCELERATOR PEDAL SENSOR)
6.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - ACCELERATOR PEDAL SENSOR)
a.

Disconnect connector A31 from the accelerator pedal sensor assembly.


b.
A388952E01
2.479,1.854 2.833,2.073 0.354,0.219 2.708,3.51 3.063,3.729 0.354,0.219 0.813,2.198 1.146,2.052 false 0.792,1.896 1.146,1.99 false 1.188,1.99 1.844,1.854 false 1.188,2.052 1.854,2.229 false 1,4.146 1.49,3.708 false 1.51,4.208 1.667,3.698 false 2.167,4.208 1.99,3.708 false 2.177,3.698 2.656,4.198 false 0.208,0.094 0.521,0.292 0.313,0.198 10 false *a 0.208,2.719 0.521,2.917 0.313,0.198 10 false *b 0.5,2.156 0.896,2.354 0.396,0.198 10 false EP2 1.885,1.76 2.344,1.958 0.458,0.198 10 false VPA1 0.406,1.813 0.865,2.01 0.458,0.198 10 false VPA2 1.896,2.167 2.292,2.365 0.396,0.198 10 false EP1 2.531,1.875 2.99,2.073 0.458,0.198 10 false A39 0.865,4.156 1.26,4.354 0.396,0.198 10 false EP2 1.344,4.219 1.802,4.417 0.458,0.198 10 false VPA2 2.083,4.219 2.479,4.417 0.396,0.198 10 false EP1 2.531,4.208 2.99,4.406 0.458,0.198 10 false VPA1 2.76,3.542 3.219,3.74 0.458,0.198 10 false A31

Disconnect connector A39 from the power management control ECU.


c.

Turn the power switch on (IG).


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage :
Tester Connection Switch Condition Specified Condition
A39-26 (VPA1) - Body ground Power switch on (IG) Below 1 V
A39-27 (VPA2) - Body ground Power switch on (IG) Below 1 V
A39-34 (EP1) - Body ground Power switch on (IG) Below 1 V
A39-35 (EP2) - Body ground Power switch on (IG) Below 1 V


Text in Illustration
*a Rear view of wire harness connector
(to Power Management Control ECU)
*b Front view of wire harness connector
(to Accelerator Pedal Sensor Assembly)

NOTICE:

Turning the power switch on (IG) with the power management control ECU connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



e.

Turn the power switch off.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Switch Condition Specified Condition
A39-26 (VPA1) - A31-6 (VPA1) Power switch off Below 1 Ω
A39-34 (EP1) - A31-5 (EP1) Power switch off Below 1 Ω
A39-27 (VPA2) - A31-3 (VPA2) Power switch off Below 1 Ω
A39-35 (EP2) - A31-2 (EP2) Power switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Switch Condition Specified Condition
A39-26 (VPA1) or A31-6 (VPA1) - Body ground and other terminals Power switch off 10 kΩ or higher
A39-34 (EP1) or A31-5 (EP1) - Body ground and other terminals Power switch off 10 kΩ or higher
A39-27 (VPA2) or A31-3 (VPA2) - Body ground and other terminals Power switch off 10 kΩ or higher
A39-35 (EP2) or A31-2 (EP2) - Body ground and other terminals Power switch off 10 kΩ or higher



g.

Connect the power management control ECU connector.


h.

Connect the accelerator pedal sensor assembly connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - ACCELERATOR PEDAL SENSOR)
a.

Disconnect connector A31 from the accelerator pedal sensor assembly.


b.

Disconnect connector A39 from the power management control ECU.


c.

Turn the power switch on (IG).


d.
A388952E04
2.479,1.854 2.833,2.073 0.354,0.219 2.708,3.51 3.063,3.729 0.354,0.219 0.813,2.198 1.146,2.052 false 0.792,1.833 1.146,1.927 false 1.188,1.917 1.844,1.781 false 1.188,2.052 1.854,2.229 false 0.885,4.198 1.365,3.708 false 1.385,4.208 1.542,3.698 false 2.01,4.208 1.833,3.708 false 2.01,3.698 2.49,4.198 false 0.208,0.094 0.521,0.292 0.313,0.198 10 false *a 0.208,2.719 0.521,2.917 0.313,0.198 10 false *b 0.5,2.156 0.896,2.354 0.396,0.198 10 false EP2 1.885,1.698 2.344,1.896 0.458,0.198 10 false VCP1 0.396,1.75 0.854,1.948 0.458,0.198 10 false VCP2 1.896,2.167 2.292,2.365 0.396,0.198 10 false EP1 2.531,1.875 2.99,2.073 0.458,0.198 10 false A39 1.271,4.229 1.667,4.427 0.396,0.198 10 false EP2 2.406,4.219 2.802,4.417 0.396,0.198 10 false EP1 2.76,3.542 3.219,3.74 0.458,0.198 10 false A31 0.667,4.229 1.125,4.427 0.458,0.198 10 false VCP2 1.844,4.229 2.302,4.427 0.458,0.198 10 false VCP1

Measure the voltage according to the value(s) in the table below.

Standard Voltage :
Tester Connection Switch Condition Specified Condition
A39-18 (VCP1) - Body ground Power switch on (IG) Below 1 V
A39-34 (EP1) - Body ground Power switch on (IG) Below 1 V
A39-19 (VCP2) - Body ground Power switch on (IG) Below 1 V
A39-35 (EP2) - Body ground Power switch on (IG) Below 1 V


Text in Illustration
*a Rear view of wire harness connector
(to Power Management Control ECU)
*b Front view of wire harness connector
(to Accelerator Pedal Sensor Assembly)

NOTICE:

Turning the power switch on (IG) with the power management control ECU connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



e.

Turn the power switch off.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Switch Condition Specified Condition
A39-18 (VCP1) - A31-4 (VCP1) Power switch off Below 1 Ω
A39-34 (EP1) - A31-5 (EP1) Power switch off Below 1 Ω
A39-19 (VCP2) - A31-1 (VCP2) Power switch off Below 1 Ω
A39-35 (EP2) - A31-2 (EP2) Power switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Switch Condition Specified Condition
A39-18 (VCP1) or A31-4 (VCP1) - Body ground and other terminals Power switch off 10 kΩ or higher
A39-34 (EP1) or A31-5 (EP1) - Body ground and other terminals Power switch off 10 kΩ or higher
A39-19 (VCP2) or A31-1 (VCP2) - Body ground and other terminals Power switch off 10 kΩ or higher
A39-35 (EP2) or A31-2 (EP2) - Body ground and other terminals Power switch off 10 kΩ or higher



g.

Connect the power management control ECU connector.


h.

Connect the accelerator pedal sensor assembly connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR