Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › from 2014.12
RM2170E _51 Engine / Hybrid System _057004 HYBRID / BATTERY CONTROL _0277924 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0AE6-225  Hybrid Battery Precharge Contactor Control Circuit Low  


DESCRIPTION

The SMRs (System Main Relays) are the relays that connect or disconnect the high voltage power system in accordance with commands from the hybrid vehicle control ECU.

There are 3 SMRs and 1 precharge resistor. SMRB, SMRP, SMRG, and the precharge resistor are located in the hybrid battery junction block assembly in the HV battery pack.

To connect to the high voltage power system, the vehicle will first turn on SMRP and SMRB to charge the vehicle through the system main resistor. Then, SMRP will be turned off after SMRG is turned on. To shut off the high voltage power system, SMRB and SMRG are turned off.

DTC No. INF Code DTC Detection Condition Trouble Area
P0AE6 225 Short to GND in the SMRP circuit
·

Wire harness or connector

·

Hybrid battery junction block assembly

·

Hybrid vehicle control ECU



WIRING DIAGRAM

A260186E17
1.271,7.344 2.479,7.51 1.208,0.167 10 false : High Voltage Line 0.208,1.406 0.969,1.604 0.76,0.198 10 false HV Battery 0.208,2.979 0.969,3.177 0.76,0.198 10 false HV Battery 0.031,2.146 0.865,2.49 0.833,0.344 10 false Service Plug Grip 1.51,0.833 1.708,1.031 0.198,0.198 10 false c1 1.542,3.531 1.74,3.729 0.198,0.198 10 false A 1.552,0.646 1.75,0.844 0.198,0.198 10 false 1 1.552,3.354 1.75,3.552 0.198,0.198 10 false 1 1.792,0.698 1.906,0.885 0.115,0.188 10 false - 1.802,3.385 1.917,3.573 0.115,0.188 10 false + 2.771,1.5 3.25,1.688 0.479,0.188 10 false SMRG 2.76,2.854 3.24,3.042 0.479,0.188 10 false SMRP 2.771,4.208 3.25,4.396 0.479,0.188 10 false SMRB 4.031,0.698 4.313,0.885 0.281,0.188 10 false CEI 4.021,3.385 4.302,3.573 0.281,0.188 10 false CBI 3.865,1.156 4.344,1.344 0.479,0.188 10 false SMRG 3.865,2.521 4.344,2.708 0.479,0.188 10 false SMRP 3.865,3.875 4.344,4.063 0.479,0.188 10 false SMRB 3.948,4.271 4.427,4.458 0.479,0.188 10 false GND 4.385,0.833 4.635,1.01 0.25,0.177 10 false P4 4.344,1.271 4.646,1.458 0.302,0.188 10 false M40 4.333,2.615 4.635,2.802 0.302,0.188 10 false M40 4.385,3.531 4.688,3.719 0.302,0.188 10 false P5 4.344,3.969 4.646,4.156 0.302,0.188 10 false M40 4.344,4.375 4.656,4.563 0.313,0.188 10 false M40 4.438,0.635 4.563,0.792 0.125,0.156 10 false 1 4.438,1.083 4.563,1.24 0.125,0.156 10 false 3 4.438,2.427 4.563,2.583 0.125,0.156 10 false 4 4.438,3.344 4.563,3.5 0.125,0.156 10 false 1 4.438,3.792 4.563,3.948 0.125,0.156 10 false 1 4.438,4.198 4.563,4.354 0.125,0.156 10 false 2 1.76,4.729 4.292,4.917 2.531,0.188 10 false Hybrid Battery Junction Block Assembly 5.833,1.24 6.313,1.427 0.479,0.188 10 false SMRG 5.833,2.604 6.313,2.792 0.479,0.188 10 false SMRP 5.833,3.958 6.313,4.146 0.479,0.188 10 false SMRB 5.479,1.271 5.802,1.448 0.323,0.177 10 false G80 5.479,2.615 5.823,2.792 0.344,0.177 10 false G80 5.479,3.969 5.771,4.146 0.292,0.177 10 false G80 5.583,1.083 5.708,1.229 0.125,0.146 10 false 1 5.583,2.417 5.708,2.573 0.125,0.156 10 false 3 5.583,3.781 5.708,3.938 0.125,0.156 10 false 4 5.198,7.219 7.094,7.385 1.896,0.167 10 false Hybrid Vehicle Control ECU 1.281,5.333 3.885,5.542 2.604,0.208 10 false to Inverter with Converter Assembly (CBI) 1.281,6.104 3.885,6.313 2.604,0.208 10 false to Inverter with Converter Assembly (CEI)

A344294E04
5.208,3.969 7.01,4.344 1.802,0.375 10 false Hybrid Vehicle Control ECU 5.698,0.885 5.99,1.052 0.292,0.167 10 false +B1 5.688,1.719 5.979,1.885 0.292,0.167 10 false +B2 5.698,2.573 6.104,2.74 0.406,0.167 10 false IG2 5.698,3.417 6.104,3.583 0.406,0.167 10 false MREL 5.323,0.896 5.667,1.042 0.344,0.146 10 false A72 5.333,1.719 5.677,1.865 0.344,0.146 10 false A71 5.333,2.552 5.677,2.698 0.344,0.146 10 false A71 5.344,3.406 5.688,3.552 0.344,0.146 10 false A72 5.406,0.708 5.615,0.865 0.208,0.156 10 false 4 5.417,1.531 5.625,1.688 0.208,0.156 10 false 1 5.417,2.375 5.625,2.531 0.208,0.156 10 false 3 5.427,3.229 5.635,3.385 0.208,0.156 10 false 6 3.552,1.865 4.323,2.042 0.771,0.177 10 false IGCT NO. 2 2,1.698 2.979,1.885 0.979,0.188 10 false to IGCT Relay 0.573,2.552 3.052,2.771 2.479,0.219 10 false to IG2 Relay (No. 1 Integration Relay) 2.031,3.396 2.938,3.594 0.906,0.198 10 false to IGCT Relay 3.615,2.708 4.385,2.885 0.771,0.177 10 false IG2 NO. 2

CAUTION / NOTICE / HINT

CAUTION:
·

Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·

After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION).

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


HINT:
·

If DTC P0AE6-225 is stored, the power switch cannot be turned on (READY).

·

After the repair, clear the DTCs, perform the following procedure and check that the same DTC (including pending DTC) is not output.

(a)

Turn the power switch off and wait for 30 seconds or more.

(b)

Turn the power switch on (READY) and wait for 30 seconds or more.

(c)

Turn the power switch off and wait for 60 seconds or more.




PROCEDURE

1.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - BODY GROUND)
a.

Disconnect connector G80 from the hybrid vehicle control ECU.


b.
U183334E02
2.104,2.365 2.521,2.698 false 2.552,2.667 3.042,2.875 0.49,0.208 10 false SMRP 0.208,0.125 0.417,0.333 0.208,0.208 10 false *a 1.302,2.396 1.646,2.552 0.344,0.156 10 false G80

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G80-3 (SMRP) - Body ground Power switch off 112 to 274 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Hybrid Vehicle Control ECU)


c.

Connect the hybrid vehicle control ECU connector.



OK

NG

2.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - HYBRID BATTERY JUNCTION BLOCK ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - HYBRID BATTERY JUNCTION BLOCK ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 hybrid vehicle battery cover panel LH (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HV RELAY ASSEMBLY>REMOVAL).


c.

Disconnect connector M40 from the hybrid battery junction block assembly.


d.

Disconnect connector G80 from the hybrid vehicle control ECU.


e.
A380673E12
1.833,2.417 2.25,2.667 0.417,0.25 1.458,3.583 1.875,3.833 0.417,0.25 2.646,1.969 2.094,1.792 false 2.396,4.385 2,3.771 false 0.094,0.135 0.406,0.333 0.313,0.198 10 false *a 0.135,2.656 0.448,2.854 0.313,0.198 10 false *b 2.688,1.906 3.229,2.271 0.542,0.365 10 false SMRP 1.896,2.458 2.208,2.656 0.313,0.198 10 false G80 1.531,3.625 1.844,3.823 0.313,0.198 10 false M40 2.313,4.396 2.865,4.635 0.552,0.24 10 false SMRP

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G80-3 (SMRP) and M40-4 (SMRP) - Body ground and other terminals Power switch off 10 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to Hybrid Vehicle Control ECU)
*b Rear view of wire harness connector
(to Hybrid Battery Junction Block Assembly)


f.

Connect the hybrid vehicle control ECU connector.


g.

Connect the hybrid battery junction block assembly connector.


h.

Install the No. 1 hybrid vehicle battery cover panel LH.



OK

REPLACE HYBRID BATTERY JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR