Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › 2011.12–2014.12
RM2170E _51 Engine / Hybrid System _057004 HYBRID / BATTERY CONTROL _0277924 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0A78-202  Drive Motor "A" Inverter Performance  


DESCRIPTION

For a description of the inverter (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0A78-266).

DTC No. INF Code DTC Detection Condition Trouble Area
P0A78 202 Malfunction (short circuit) in the motor inverter inside the inverter with converter assembly
·

Inverter with converter assembly

·

Hybrid vehicle transaxle assembly

·

Motor cable



CAUTION / NOTICE / HINT

CAUTION:
·

Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·

After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION).

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:
·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

DTC P0A78-202 is stored after any of DTCs P0A78-113, 284, 286, 287, 505 and 506 are stored. After troubleshooting and repairing DTC P0A78-202, be sure to troubleshoot all the other DTCs.

·

Depending on the conditions in which the vehicle is being operated when a short circuit occurs in the inverter with converter assembly, the hybrid vehicle transaxle assembly may be affected. As this DTC is stored if a short circuit occurs in the inverter with converter assembly, it is necessary to perform a road test to check the hybrid vehicle transaxle assembly. If problems are found, replace the malfunctioning parts.

·

After completing the repair, including the repair of previously output DTCs, drive the vehicle at a speed of approximately 40 km/h (25 mph) for 1 minute and check that DTC P0A90-251 (Drive Motor "A" Performance) is not output. If DTC P0A90-251 (Drive Motor "A" Performance) is output, replace the hybrid vehicle transaxle assembly.



HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

With the vehicle engine stopped, the power switch on (READY) and the shift lever in P, depress the accelerator pedal to start the engine.

2.

Perform a road test according to the freeze frame data and item "Vehicle Spd" for approximately 10 minutes.



PROCEDURE

1.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MG2)

OK

2.REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS

NG

4.CHECK MOTOR CABLE (FOR MG2)
2.REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS

NEXT

3.CHECK DTC OUTPUT (HYBRID CONTROL)
3.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Check the other DTCs that were output together with DTC P0A78-202.

Result:
DTC No. Relevant Diagnosis
P0A78-113, 284, 286, 287, 505, 506 Drive Motor "A" Inverter Performance


NOTICE:

DTC P0A78-202 is stored after any of DTCs P0A78-113, 284, 286, 287, 505 and 506 are stored. After troubleshooting and repairing DTC P0A78-202, be sure to troubleshoot all the other DTCs.




NEXT

4.CHECK MOTOR CABLE (FOR MG2)

OK

5.REPLACE HYBRID VEHICLE TRANSAXLE ASSEMBLY

NG

8.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MG2)
5.REPLACE HYBRID VEHICLE TRANSAXLE ASSEMBLY

NEXT

6.REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS
6.REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS

NEXT

7.CHECK DTC OUTPUT (HYBRID CONTROL)
7.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Check the other DTCs that were output together with DTC P0A78-202.

Result:
DTC No. Relevant Diagnosis
P0A78-113, 284, 286, 287, 505, 506 Drive Motor "A" Inverter Performance


NOTICE:

DTC P0A78-202 is stored after any of DTCs P0A78-113, 284, 286, 287, 505 and 506 are stored. After troubleshooting and repairing DTC P0A78-202, be sure to troubleshoot all the other DTCs.




NEXT

8.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MG2)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the motor cable (for MG2) from the hybrid vehicle transaxle assembly.


c.
U159037E02
1.896,1.25 2.885,1.427 false 2.896,0.563 1.896,0.74 false 1.896,0.99 2.896,0.99 false 2.938,0.479 3.146,0.646 0.208,0.167 10 false W 2.938,1.354 3.083,1.51 0.146,0.156 10 false U 2.938,0.896 3.083,1.063 0.146,0.167 10 false V 0.938,0.948 1.115,1.115 0.177,0.167 10 false a3 0.042,0.042 0.281,0.229 0.24,0.188 10 true *a

Check MG2 for an interphase short using a milliohmmeter.

i.

Using a milliohmmeter, measure the resistance according to the value(s) in the table below.

HINT:

If the MG2 temperature is high, the resistance will vary greatly from the specification. Therefore, measure the resistance at least 8 hours after the vehicle is stopped.


Standard Resistance:
Tester Connection Switch Condition Specified Condition
a3-1 (W) - a3-3 (U) Power switch off 170.3 to 188.1 mΩ
a3-2 (V) - a3-1 (W) Power switch off 170.3 to 188.1 mΩ
a3-3 (U) - a3-2 (V) Power switch off 170.3 to 188.1 mΩ


Text in Illustration
*a Component without motor cable (for MG2) connected
(Hybrid Vehicle Transaxle Assembly)

HINT:

To correct the variation of the measured resistance due to temperature, use the following formula to calculate the resistance at 20°C (68° F).

R20 = Rt / {1 + 0.00393 X (T - 20)}


The calculation is based on the following:

R20: Resistance at 20°C (68° F) (mΩ)

Rt: Measured resistance (mΩ)

T: Temperature when the resistance is measured (° C)





d.

Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.


Standard Resistance:
Tester Connection Switch Condition Specified Condition
a3-1 (W) - Body ground Power switch off 100 MΩ or higher
a3-2 (V) - Body ground Power switch off 100 MΩ or higher
a3-3 (U) - Body ground Power switch off 100 MΩ or higher



e.

Connect the motor cable (for MG2).



OK

9.REPLACE MOTOR CABLE

NG

12.REPLACE MOTOR CABLE
9.REPLACE MOTOR CABLE

NEXT

10.REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS
10.REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS

NEXT

11.CHECK DTC OUTPUT (HYBRID CONTROL)
11.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Check the other DTCs that were output together with DTC P0A78-202.

Result:
DTC No. Relevant Diagnosis
P0A78-113, 284, 286, 287, 505, 506 Drive Motor "A" Inverter Performance


NOTICE:

DTC P0A78-202 is stored after any of DTCs P0A78-113, 284, 286, 287, 505 and 506 are stored. After troubleshooting and repairing DTC P0A78-202, be sure to troubleshoot all the other DTCs.




NEXT

12.REPLACE MOTOR CABLE

NEXT

13.REPLACE HYBRID VEHICLE TRANSAXLE ASSEMBLY
13.REPLACE HYBRID VEHICLE TRANSAXLE ASSEMBLY

NEXT

14.REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS
14.REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS

NEXT

15.CHECK DTC OUTPUT (HYBRID CONTROL)
15.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Check the other DTCs that were output together with DTC P0A78-202.

Result:
DTC No. Relevant Diagnosis
P0A78-113, 284, 286, 287, 505, 506 Drive Motor "A" Inverter Performance


NOTICE:

DTC P0A78-202 is stored after any of DTCs P0A78-113, 284, 286, 287, 505 and 506 are stored. After troubleshooting and repairing DTC P0A78-202, be sure to troubleshoot all the other DTCs.




NEXT