For a description of the inverter (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0D2F-266).
| DTC No. | INF Code | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| P0A78 | 202 | Malfunction (short circuit) in the motor inverter inside the inverter with converter assembly | ·
Inverter with converter assembly ·
Hybrid vehicle transaxle assembly ·
Motor cable |
Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.
After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION).
Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
DTC P0A78-202 is stored after any of DTCs P0A1B-505, P0A40-506, P0A78-113, 284, 286 and 287 are stored. After troubleshooting and repairing DTC P0A78-202, be sure to troubleshoot all the other DTCs.
Depending on the conditions in which the vehicle is being operated when a short circuit occurs in the inverter with converter assembly, the hybrid vehicle transaxle assembly may be affected. As this DTC is stored if a short circuit occurs in the inverter with converter assembly, it is necessary to perform a road test to check the hybrid vehicle transaxle assembly. If problems are found, replace the malfunctioning parts.
After completing the repair, including the repair of previously output DTCs, drive the vehicle at a speed of approximately 40 km/h (25 mph) for 1 minute and check that DTC P0A90-251 (Drive Motor "A" Performance) is not output. If DTC P0A90-251 (Drive Motor "A" Performance) is output, replace the hybrid vehicle transaxle assembly.
After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.
With the vehicle engine stopped, the power switch on (READY) and the shift lever in P, depress the accelerator pedal to start the engine.
Perform a road test according to the freeze frame data and item "Vehicle Spd" for approximately 10 minutes.
OK
NG
NEXT
Check the other DTCs that were output together with DTC P0A78-202.
| DTC No. | Relevant Diagnosis |
|---|---|
| P0A1B-505 | Drive Motor "A" Control Module |
| P0A40-506 | Drive Motor "A" Position Sensor Circuit Range/ Performance |
| P0A78-113, 284, 286, 287 | Drive Motor "A" Inverter Performance |
DTC P0A78-202 is stored after any of DTCs P0A1B-505, P0A40-506, P0A78-113, 284, 286 and 287 are stored. After troubleshooting and repairing DTC P0A78-202, be sure to troubleshoot all the other DTCs.
NEXT
(See pageEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>DIAGNOSTIC TROUBLE CODE CHART)
OK
NG
NEXT
NEXT
Check the other DTCs that were output together with DTC P0A78-202.
| DTC No. | Relevant Diagnosis |
|---|---|
| P0A1B-505 | Drive Motor "A" Control Module |
| P0A40-506 | Drive Motor "A" Position Sensor Circuit Range/ Performance |
| P0A78-113, 284, 286, 287 | Drive Motor "A" Inverter Performance |
DTC P0A78-202 is stored after any of DTCs P0A1B-505, P0A40-506, P0A78-113, 284, 286 and 287 are stored. After troubleshooting and repairing DTC P0A78-202, be sure to troubleshoot all the other DTCs.
NEXT
(See pageEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>DIAGNOSTIC TROUBLE CODE CHART)
Be sure to wear insulated gloves.
Check that the service plug grip is not installed.
After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.
Disconnect the motor cable (for MG2) from the hybrid vehicle transaxle assembly.
Check MG2 for an interphase short using a milliohmmeter.
Using a milliohmmeter, measure the resistance according to the value(s) in the table below.
If the MG2 temperature is high, the resistance will vary greatly from the specification. Therefore, measure the resistance at least 8 hours after the vehicle is stopped.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| a3-1 (W) - a3-3 (U) | Power switch off | 170.3 to 188.1 mΩ |
| a3-2 (V) - a3-1 (W) | Power switch off | 170.3 to 188.1 mΩ |
| a3-3 (U) - a3-2 (V) | Power switch off | 170.3 to 188.1 mΩ |
| *a | Component without motor cable (for MG2) connected
(Hybrid Vehicle Transaxle Assembly) |
To correct the variation of the measured resistance due to temperature, use the following formula to calculate the resistance at 20°C (68° F).
R20 = Rt / {1 + 0.00393 X (T - 20)}
The calculation is based on the following:
R20: Resistance at 20°C (68° F) (mΩ)
Rt: Measured resistance (mΩ)
T: Temperature when the resistance is measured (° C)
Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.
Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| a3-1 (W) - Body ground | Power switch off | 100 MΩ or higher |
| a3-2 (V) - Body ground | Power switch off | 100 MΩ or higher |
| a3-3 (U) - Body ground | Power switch off | 100 MΩ or higher |
Connect the motor cable (for MG2).
OK
NG
NEXT
NEXT
Check the other DTCs that were output together with DTC P0A78-202.
| DTC No. | Relevant Diagnosis |
|---|---|
| P0A1B-505 | Drive Motor "A" Control Module |
| P0A40-506 | Drive Motor "A" Position Sensor Circuit Range/ Performance |
| P0A78-113, 284, 286, 287 | Drive Motor "A" Inverter Performance |
DTC P0A78-202 is stored after any of DTCs P0A1B-505, P0A40-506, P0A78-113, 284, 286 and 287 are stored. After troubleshooting and repairing DTC P0A78-202, be sure to troubleshoot all the other DTCs.
NEXT
(See pageEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>DIAGNOSTIC TROUBLE CODE CHART)
NEXT
NEXT
NEXT
Check the other DTCs that were output together with DTC P0A78-202.
| DTC No. | Relevant Diagnosis |
|---|---|
| P0A1B-505 | Drive Motor "A" Control Module |
| P0A40-506 | Drive Motor "A" Position Sensor Circuit Range/ Performance |
| P0A78-113, 284, 286, 287 | Drive Motor "A" Inverter Performance |
DTC P0A78-202 is stored after any of DTCs P0A1B-505, P0A40-506, P0A78-113, 284, 286 and 287 are stored. After troubleshooting and repairing DTC P0A78-202, be sure to troubleshoot all the other DTCs.
NEXT
(See pageEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>DIAGNOSTIC TROUBLE CODE CHART)