Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › from 2014.12
RM2170E _51 Engine / Hybrid System _057004 HYBRID / BATTERY CONTROL _0277924 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0A78-113  Drive Motor "A" Inverter Performance  


DESCRIPTION

For a description of the inverter (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0D2F-266).

If the motor inverter overheats, has a circuit malfunction, or has an internal short, the inverter transmits this information to the MG ECU via the motor inverter fail signal line.

HINT:

The term "drive motor A" indicates MG2.


DTC No. INF Code DTC Detection Condition Trouble Area
P0A78 113 Motor inverter fail signal detection
(System overcurrent)
·

Wire harness or connector

·

Hybrid vehicle transaxle assembly

·

Motor cable

·

Inverter with converter assembly

·

Hybrid vehicle control ECU

·

PCU fuse



WIRING DIAGRAM

Refer to the wiring diagram for DTC P1CAC-200 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P1CAC-200).

Refer to the wiring diagram for DTC P0AA6-526 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0AA6-526).

Refer to the wiring diagram for DTC P324E-788 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P324E-788).

Refer to the wiring diagram for DTC U0110-159 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>U0110-159).

CAUTION / NOTICE / HINT

CAUTION:
·

Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·

After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION).

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Turn the power switch on (READY) and wait for 5 seconds or more.

2.

Perform a road test according to the freeze frame data "Vehicle Spd" for approximately 10 minutes.



PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / DTC.


d.

Check if DTCs are output.

Result:
Result Proceed to
P0A78-113 is set before any of the DTCs in the table below are set. A
Any of the DTCs including pending DTCs in the table 1 below are set before P0A78-113 is set. B
Any of the DTCs in the table 2 below are set before P0A78-113 is set. C


Table 1
DTC No. Relevant Diagnosis
P0ADB-227 Hybrid Battery Positive Contactor Control Circuit Low
P0ADC-226 Hybrid Battery Positive Contactor Control Circuit High
P0ADF-229 Hybrid Battery Negative Contactor Control Circuit Low
P0AE0-228 Hybrid Battery Negative Contactor Control Circuit High
P3004-803 High Voltage Power Resource

Table 2
DTC No. Relevant Diagnosis
P0A9C-123 Hybrid Battery Temperature Sensor "A" Range / Performance
P0A9D-123 Hybrid Battery Temperature Sensor "A" Circuit Low
P0A9E-123 Hybrid Battery Temperature Sensor "A" Circuit High
P0AC0-123 Hybrid Battery Pack Current Sensor Circuit Range / Performance
P0AC1-123 Hybrid Battery Pack Current Sensor Circuit Low
P0AC2-123 Hybrid Battery Pack Current Sensor Circuit High
P0AC6-123 Hybrid Battery Temperature Sensor "B" Range / Performance
P0AC7-123 Hybrid Battery Temperature Sensor "B" Circuit Low
P0AC8-123 Hybrid Battery Temperature Sensor "B" Circuit High
P0ACB-123 Hybrid Battery Temperature Sensor "C" Range / Performance
P0ACC-123 Hybrid Battery Temperature Sensor "C" Circuit Low
P0ACD-123 Hybrid Battery Temperature Sensor "C" Circuit High
P0AFC-123 Hybrid Battery Pack Sensor Module
P3011-123, P3012-123, P3013-123, P3014-123, P3015-123, P3016-123, P3017-123, P3018-123, P3019-123, P3020-123 Battery Block # Becomes Weak
P3065-123 Hybrid Battery Temperature Sensor Range / Performance Stuck "A"
P308A-123 Hybrid Battery Voltage Sensor All Circuits Low

HINT:
·

Refer to the Freeze Frame data to determine the order in which the DTCs were set.

·

P0A78-113 may be set due to a malfunction which also causes DTCs in the preceding table to be set. In this case, first troubleshoot the output DTCs in the preceding table. Then, perform a test to attempt to reproduce the problems, and check that no DTCs are output.




e.

Turn the power switch off.



A

2.CHECK DTC OUTPUT (HYBRID CONTROL)

B

C

2.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / DTC.


d.

Check if DTCs are output.

Result:
Result Proceed to
P0A78-202 is not output. A
P0A78-202 is also output. B


NOTICE:
·

If P0A78-202 is output, troubleshoot it first. After completing the troubleshooting for P0A78-202, return to perform troubleshooting for this DTC.

·

Parts repaired or replaced during troubleshooting for P0A78-202 do not need to be re-inspected in this diagnosis procedure.




e.

Turn the power switch off.



A

3.CHECK DTC OUTPUT (HYBRID CONTROL)

B

3.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / DTC.


d.

Check if DTCs are output.

HINT:
·

If P0A78-202 was not output in step 2 of this diagnosis procedure, check Table 1 below.

·

If P0A78-202 was output in step 2 of this diagnosis procedure, repair that DTC first, then check Table 2 below.



Result:
Result Proceed to
Only P0A78-113 is output, or DTCs other than the ones in the table below are also output. A
Any of the following DTCs including pending DTCs are also output. B


Table 1
DTC No. Relevant Diagnosis
P06B0-163 Sensor Power Supply "A" Circuit/Open
P06D6-511 Sensor Reference Voltage "F" Circuit/Open
P06E6-164 Sensor Power Supply "C" Circuit/Open
P0A1A-151, 166, 517, 658, 791, 809 Generator Control Module
P0A1B-198, 503, 505, 547, 554, 786, 794, 806 Drive Motor "A" Control Module
P0A1D (all INF codes)*1 Hybrid Powertrain Control Module
P0A3F-243 Drive Motor "A" Position Sensor Circuit
P0A40-500, 504, 506, 549, 556, 808 Drive Motor "A" Position Sensor Circuit Range/Performance
P0A41-245 Drive Motor "A" Position Sensor Circuit Low
P0A4B-253 Generator Position Sensor Circuit
P0A4C-513, 518, 811 Generator Position Sensor Circuit Range/Performance
P0A4D-255 Generator Position Sensor Circuit Low
P0A78-279, 287, 548, 555, 807 Drive Motor "A" Inverter Performance
P0A7A-325, 810 Generator Inverter Performance
P0A90-509 Drive Motor "A" Performance
P0A92-521 Hybrid Generator Performance
P0ADB-227 Hybrid Battery Positive Contactor Control Circuit Low
P0ADC-226 Hybrid Battery Positive Contactor Control Circuit High
P0ADF-229 Hybrid Battery Negative Contactor Control Circuit Low
P0AE0-228 Hybrid Battery Negative Contactor Control Circuit High
P0BEA-290 Drive Motor "A" Phase V Current Sensor Circuit Range/Performance
P0BEE-298 Drive Motor "A" Phase W Current Sensor Circuit Range/Performance
P0C19-306 Drive Motor "A" Torque Delivered Performance
P0C76-523 Hybrid Battery System Discharge Time Too Long
P0CA3-442 DC/DC Converter Step Up Voltage Performance
P0D2E-586 Drive Motor "A" Inverter Voltage Sensor Circuit Range/Performance
P0D2F-266 Drive Motor "A" Inverter Voltage Sensor Circuit Low
P0D30-267 Drive Motor "A" Inverter Performance
P0E05-328 Generator Phase V Current Sensor Circuit Range/Performance
P0E09-336 Generator Phase W Current Sensor Circuit Range/Performance
P0E32-585 DC/DC Converter Voltage Sensor "A" Range/Performance
P0E33-589 DC/DC Converter Voltage Sensor "A" Low
P0E34-590 DC/DC Converter Voltage Sensor "A" High
P0E71-344 Generator Torque Delivered Performance
P1C2A-155 Generator A/D Converter Circuit
P1C2B-192 Drive Motor "A" A/D Converter Circuit
P1C2D-587 Hybrid Battery Voltage / DC/DC Converter Voltage Correlation
P1C3C-294 Drive Motor "A" Phase V Current Sensor Correlation
P1C3D-302 Drive Motor "A" Phase W Current Sensor Correlation
P1C3E-333 Generator Phase V Current Sensor Correlation
P1C3F-341 Generator Phase W Current Sensor Correlation
P1C4A-288 Drive Motor "A" Phase V Current Sensor Sub Circuit Range/Performance
P1C4F-296 Drive Motor "A" Phase W Current Sensor Sub Circuit Range/Performance
P1C54-326 Generator Phase V Current Sensor Sub Circuit Range/Performance
P1C59-334 Generator Phase W Current Sensor Sub Circuit Range/Performance
P1C6D-501 Drive Motor "A" Phase V Current Sensor Offset Range/Performance
P1C6E-502 Drive Motor "A" Phase W Current Sensor Offset Range/Performance
P1C71-515 Generator Phase V Current Sensor Offset Range/Performance
P1C72-516 Generator Phase W Current Sensor Offset Range/Performance
P1C73-512 Sensor Standard Voltage "F" Circuit/Open
P1CA6-156 Generator Control Module Malfunction
P1CA7-193 Drive Motor Control Module Malfunction
P1CAC-200 Generator Position Sensor Angle Malfunction
P1CAD-168 Drive Motor "A" Position Sensor Angle Malfunction
P1CAF-792 Generator Position Sensor REF Signal Cycle Malfunction
P1CB0-795 Drive Motor "A" Position Sensor REF Signal Cycle Malfunction
P1CB2-793 Generator Position Sensor REF Signal Stop Malfunction
P1CB3-796 Drive Motor "A" Position Sensor REF Signal Stop Malfunction
P3004-803 High Voltage Power Resource
P3133-659 Communication Error from Generator to Drive Motor "A"
P3134-661 Communication Error from Drive Motor "A" to Generator

Table 2
DTC No. Relevant Diagnosis
P06B0-163 Sensor Power Supply "A" Circuit/Open
P06D6-511 Sensor Reference Voltage "F" Circuit/Open
P06E6-164 Sensor Power Supply "C" Circuit/Open
P0A1A-151, 166, 517, 658, 791, 809 Generator Control Module
P0A1B-198, 503, 505, 547, 554, 786, 794, 806 Drive Motor "A" Control Module
P0A1D (all INF codes)*1 Hybrid Powertrain Control Module
P0A3F-243 Drive Motor "A" Position Sensor Circuit
P0A40-500, 504, 506, 549, 556, 808 Drive Motor "A" Position Sensor Circuit Range/Performance
P0A41-245 Drive Motor "A" Position Sensor Circuit Low
P0A4B-253 Generator Position Sensor Circuit
P0A4C-513, 518, 811 Generator Position Sensor Circuit Range/Performance
P0A4D-255 Generator Position Sensor Circuit Low
P0A78-279, 287, 548, 555, 807 Drive Motor "A" Inverter Performance
P0A7A-325, 810 Generator Inverter Performance
P0A92-521 Hybrid Generator Performance
P0ADB-227 Hybrid Battery Positive Contactor Control Circuit Low
P0ADC-226 Hybrid Battery Positive Contactor Control Circuit High
P0ADF-229 Hybrid Battery Negative Contactor Control Circuit Low
P0AE0-228 Hybrid Battery Negative Contactor Control Circuit High
P0C76-523 Hybrid Battery System Discharge Time Too Long
P0CA3-442 DC/DC Converter Step Up Voltage Performance
P0D2E-586 Drive Motor "A" Inverter Voltage Sensor Circuit Range/Performance
P0D2F-266 Drive Motor "A" Inverter Voltage Sensor Circuit Low
P0D30-267 Drive Motor "A" Inverter Performance
P0E05-328 Generator Phase V Current Sensor Circuit Range/Performance
P0E09-336 Generator Phase W Current Sensor Circuit Range/Performance
P0E32-585 DC/DC Converter Voltage Sensor "A" Range/Performance
P0E33-589 DC/DC Converter Voltage Sensor "A" Low
P0E34-590 DC/DC Converter Voltage Sensor "A" High
P0E71-344 Generator Torque Delivered Performance
P1C2A-155 Generator A/D Converter Circuit
P1C2B-192 Drive Motor "A" A/D Converter Circuit
P1C2D-587 Hybrid Battery Voltage / DC/DC Converter Voltage Correlation
P1C3C-294 Drive Motor "A" Phase V Current Sensor Correlation
P1C3D-302 Drive Motor "A" Phase W Current Sensor Correlation
P1C3E-333 Generator Phase V Current Sensor Correlation
P1C3F-341 Generator Phase W Current Sensor Correlation
P1C54-326 Generator Phase V Current Sensor Sub Circuit Range/Performance
P1C59-334 Generator Phase W Current Sensor Sub Circuit Range/Performance
P1C71-515 Generator Phase V Current Sensor Offset Range/Performance
P1C72-516 Generator Phase W Current Sensor Offset Range/Performance
P1C73-512 Sensor Standard Voltage "F" Circuit/Open
P1CA6-156 Generator Control Module Malfunction
P1CA7-193 Drive Motor Control Module Malfunction
P1CAC-200 Generator Position Sensor Angle Malfunction
P1CAD-168 Drive Motor "A" Position Sensor Angle Malfunction
P1CAF-792 Generator Position Sensor REF Signal Cycle Malfunction
P1CB0-795 Drive Motor "A" Position Sensor REF Signal Cycle Malfunction
P1CB2-793 Generator Position Sensor REF Signal Stop Malfunction
P1CB3-796 Drive Motor "A" Position Sensor REF Signal Stop Malfunction
P3004-803 High Voltage Power Resource
P3133-659 Communication Error from Generator to Drive Motor "A"
P3134-661 Communication Error from Drive Motor "A" to Generator

HINT:
·

*1: If any INF codes are output for this DTC, refer to the corresponding diagnostic procedure.

·

P0A78-113 may be set due to a malfunction which also causes DTCs in the preceding table to be set. In this case, first troubleshoot the output DTCs in the preceding table. Then, perform a test to attempt to reproduce the problems, and check that no DTCs are output.




e.

Turn the power switch off.



A

4.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

B

4.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

OK

5.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - GENERATOR RESOLVER)

NG

CONNECT SECURELY

5.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - GENERATOR RESOLVER)

OK

6.CHECK GENERATOR RESOLVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK GENERATOR RESOLVER

OK

7.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - MOTOR RESOLVER)

NG

21.CHECK CONNECTOR CONNECTION CONDITION (GENERATOR RESOLVER CONNECTOR)
7.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - MOTOR RESOLVER)

OK

8.CHECK MOTOR RESOLVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK MOTOR RESOLVER

OK

9.CHECK INVERTER WITH CONVERTER ASSEMBLY (MOTOR CABLE (FOR MG1) CONNECTION CONDITION)

NG

23.CHECK CONNECTOR CONNECTION CONDITION (MOTOR RESOLVER CONNECTOR)
9.CHECK INVERTER WITH CONVERTER ASSEMBLY (MOTOR CABLE (FOR MG1) CONNECTION CONDITION)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A258644

Remove the inverter terminal cover from the inverter with converter assembly.


c.
A258645

Remove the inverter cover from the inverter with converter assembly.


d.
A258647E02
1.094,1.115 1.25,1.302 0.156,0.188 10 true A 1.24,0.365 1.396,0.542 0.156,0.177 10 true B 2.438,0.896 2.594,1.073 0.156,0.177 10 true B 1.438,1.51 1.594,1.698 0.156,0.188 10 true A 1.781,1.646 1.938,1.833 0.156,0.188 10 true A

Check that the bolts for the motor cable (for MG1) are tightened to the specified torque, the motor cable (for MG1) is connected securely, and there are no contact problems.

Specified Condition:
Bolt A:

T=8.0 N*m (82 kgf*cm, 71 in.*lbf)

Bolt B:

T=9.2 N*m (94 kgf*cm, 81 ft.*lbf)


NOTICE:

Make sure that the tightening torque of the bolt B is between 6.4 and 12 N*m (65 and 122 kgf*cm, 57 and 106 in.*lbf).



e.

Disconnect the motor cable (for MG1) from the inverter with converter assembly.


f.

Check for arc marks at the terminals for the motor cable (for MG1).

Result:
Result Proceed to
The terminals are connected securely and there are no contact problems. There are no arc marks. A
The terminals are not connected securely and there is a contact problem. There are arc marks. B
The terminals are not connected securely and there is a contact problem. There are no arc marks. C
The terminals are connected securely and there are no contact problems. There are arc marks. B



g.

Connect the motor cable (for MG1) to the inverter with converter assembly.


h.

Install the inverter cover.


i.

Install the inverter terminal cover.



A

10.CHECK INVERTER WITH CONVERTER ASSEMBLY (MOTOR CABLE (FOR MG2) CONNECTION CONDITION)

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY

10.CHECK INVERTER WITH CONVERTER ASSEMBLY (MOTOR CABLE (FOR MG2) CONNECTION CONDITION)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A258644

Remove the inverter terminal cover from the inverter with converter assembly.


c.
A258646E02
1.771,1.542 2,1.708 0.229,0.167 10 false A 1.917,0.688 2.083,0.875 0.167,0.188 10 true B 3.167,1.208 3.313,1.385 0.146,0.177 10 true B 2.115,1.844 2.344,2.01 0.229,0.167 10 false A 2.417,1.958 2.646,2.125 0.229,0.167 10 true A

Check that the bolts for the motor cable (for MG2) are tightened to the specified torque, the motor cable (for MG2) is connected securely, and there are no contact problems.

Specified Condition:
Bolt A:

T=8.0 N*m (82 kgf*cm, 71 in.*lbf)

Bolt B:

T=9.2 N*m (94 kgf*cm, 81 ft.*lbf)


NOTICE:

Make sure that the tightening torque of the bolt B is between 6.4 and 12 N*m (65 and 122 kgf*cm, 57 and 106 in.*lbf).



d.

Disconnect the motor cable (for MG2) from the inverter with converter assembly.


e.

Check for arc marks at the terminals for the motor cable (for MG2).

Result:
Result Proceed to
The terminals are connected securely and there are no contact problems. There are no arc marks. A
The terminals are not connected securely and there is a contact problem. There are arc marks. B
The terminals are not connected securely and there is a contact problem. There are no arc marks. C
The terminals are connected securely and there are no contact problems. There are arc marks. B



f.

Connect the motor cable (for MG2) to the inverter with converter assembly.


g.

Install the inverter terminal cover.



A

11.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MG1)

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY

11.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MG1)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A258644

Remove the inverter terminal cover from the inverter with converter assembly.


c.
A258645

Remove the inverter cover from the inverter with converter assembly.


d.
A258648

Disconnect the motor cable from the inverter with converter assembly.


e.
U159086E01
0.18,0.142 0.386,0.369 0.206,0.227 10 *a 0.266,0.893 0.472,1.119 0.206,0.227 10 *1 1.046,1.884 1.251,2.047 0.206,0.163 10 W 1.643,1.884 1.793,2.042 0.150,0.158 10 U 2.245,1.89 2.450,2.057 0.206,0.168 10 V 0.855,0.954 0.5,0.954 false 1.261,1.732 1.151,1.877 false 2.152,1.728 2.258,1.877 false 1.703,1.74 1.703,1.877 false 0.533,1.296 0.714,1.461 0.181,0.165 10 a2

Check MG1 for an interphase short using a milliohmmeter.

i.

Using a milliohmmeter, measure the resistance according to the value(s) in the table below.

HINT:

If the MG1 temperature is high, the resistance will vary greatly from the specification. Therefore, measure the resistance at least 8 hours after the vehicle is stopped.


Standard Resistance:
Tester Connection Switch Condition Specified Condition
a2-1 (W) - a2-2 (U) Power switch off 139.1 to 153.7 mΩ
a2-2 (U) - a2-3 (V) Power switch off 139.1 to 153.7 mΩ
a2-3 (V) - a2-1 (W) Power switch off 139.1 to 153.7 mΩ


Text in Illustration
*1 Shield Ground
*a Motor Cable (for MG1)
(Inverter with Converter Assembly Side)

HINT:

To correct the variation of the measured resistance due to temperature, use the following formula to calculate the resistance at 20°C (68° F).

R20 = Rt / {1 + 0.00393 X (T - 20)}


The calculation is based on the following:

R20: Resistance at 20°C (68° F) (mΩ)

Rt: Measured resistance (mΩ)

T: Temperature when the resistance is measured (°C)





f.

Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.


Standard Resistance:
Tester Connection Switch Condition Specified Condition
a2-1 (W) - Body ground and shield ground Power switch off 100 MΩ or higher
a2-2 (U) - Body ground and shield ground Power switch off 100 MΩ or higher
a2-3 (V) - Body ground and shield ground Power switch off 100 MΩ or higher



g.

Connect the motor cable.


h.

Install the inverter cover.


i.

Install the inverter terminal cover.



OK

12.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MG2)

NG

28.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MOTOR CABLE (FOR MG1) CONNECTION CONDITION)
12.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MG2)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A258644

Remove the inverter terminal cover from the inverter with converter assembly.


c.
A258645

Remove the inverter cover from the inverter with converter assembly.


d.
A258648

Disconnect the motor cable from the inverter with converter assembly.


e.
U159089E01
0.117,0.11 0.343,0.336 0.225,0.225 10 *a 0.324,0.878 0.570,1.059 0.246,0.181 10 *1 1.183,1.932 1.371,2.097 0.188,0.165 10 W 1.676,1.938 1.864,2.103 0.188,0.165 10 U 2.157,1.932 2.345,2.097 0.188,0.165 10 V 1.345,1.763 1.303,1.932 false 1.733,1.763 1.733,1.938 false 2.113,1.763 2.183,1.932 false 0.893,0.973 0.504,0.973 false 0.536,1.303 0.747,1.466 0.211,0.163 10 a4

Check MG2 for an interphase short using a milliohmmeter.

i.

Using a milliohmmeter, measure the resistance according to the value(s) in the table below.

HINT:

If the MG2 temperature is high, the resistance will vary greatly from the specification. Therefore, measure the resistance at least 8 hours after the vehicle is stopped.


Standard Resistance:
Tester Connection Switch Condition Specified Condition
a4-1 (W) - a4-2 (U) Power switch off 172.5 to 190.7 mΩ
a4-2 (U) - a4-3 (V) Power switch off 172.5 to 190.7 mΩ
a4-3 (V) - a4-1 (W) Power switch off 172.5 to 190.7 mΩ


Text in Illustration
*1 Shield Ground
*a Motor Cable (for MG2)
(Inverter with Converter Assembly Side)

HINT:

To correct the variation of the measured resistance due to temperature, use the following formula to calculate the resistance at 20°C (68° F).

R20 = Rt / {1 + 0.00393 X (T - 20)}


The calculation is based on the following:

R20: Resistance at 20°C (68° F) (mΩ)

Rt: Measured resistance (mΩ)

T: Temperature when the resistance is measured (°C)





f.

Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.


Standard Resistance:
Tester Connection Switch Condition Specified Condition
a4-1 (W) - Body ground and shield ground Power switch off 100 MΩ or higher
a4-2 (U) - Body ground and shield ground Power switch off 100 MΩ or higher
a4-3 (V) - Body ground and shield ground Power switch off 100 MΩ or higher



g.

Connect the motor cable.


h.

Install the inverter cover.


i.

Install the inverter terminal cover.



OK

13.CHECK FUSE (PCU)

NG

30.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MOTOR CABLE (FOR MG2) CONNECTION CONDITION)
13.CHECK FUSE (PCU)
a.
A263604E01
0.18,0.156 0.387,0.312 0.207,0.156 10 *1 2.776,2.786 2.982,2.941 0.207,0.156 10 *2 2.57,2.315 2.846,2.766 false

Remove the PCU fuse from the No. 2 engine room relay block and No. 2 junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
PCU fuse terminal Always Below 1Ω


Text in Illustration
*1 No. 2 Engine Room Relay Block and No. 2 Junction Block Assembly
*2 PCU fuse


c.

Install the PCU fuse.



OK

14.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY POWER SOURCE CIRCUIT)

NG

25.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - PCU FUSE)
14.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY POWER SOURCE CIRCUIT)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect connector A47 from inverter with converter assembly.


c.
U158865E02
2.125,0.969 1.979,0.375 false 2.281,0.969 2.427,0.375 false 1.99,1.708 2.115,1.198 false 2.469,1.729 2.271,1.198 false 1.813,0.156 2.125,0.344 0.313,0.188 10 false +B2 1.646,1.74 2.135,1.927 0.49,0.188 10 false GND2 2.396,1.75 2.885,1.938 0.49,0.188 10 false GND1 2.396,0.156 2.708,0.344 0.313,0.188 10 false +B 0.177,0.104 0.49,0.292 0.313,0.188 10 false *a 0.344,1.063 0.667,1.25 0.323,0.188 10 false A47

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A47-28 (GND1) - Body ground Power switch off Below 1 Ω
A47-27 (GND2) - Body ground Power switch off Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Inverter with Converter Assembly)


d.

Connect the cable to the negative (-) auxiliary battery terminal.


e.

Turn the power switch on (IG).


f.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A47-10 (+B) - Body ground Power switch on (IG) Same as auxiliary battery voltage
A47-9 (+B2) - Body ground Power switch on (IG) Same as auxiliary battery voltage


NOTICE:

Turning the power switch on (IG) with the inverter with converter assembly connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



g.

Turn the power switch off.


h.

Disconnect the cable from the negative (-) auxiliary battery terminal.


i.

Connect the inverter with converter assembly connector.



OK

15.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - HYBRID VEHICLE CONTROL ECU)

NG

REPAIR OR REPLACE POWER SOURCE CIRCUIT

15.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - HYBRID VEHICLE CONTROL ECU)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect connector A47 from the inverter with converter assembly.


c.

Disconnect connector A72 from the hybrid vehicle control ECU.


d.
A379052E03
0.25,0.917 0.667,1.167 0.417,0.25 0.833,1.833 1.604,1.052 false 0.938,0.365 1.583,0.938 false 1.385,0.344 1.708,0.948 false 2.063,0.365 1.833,0.938 false 2.615,0.375 1.948,0.948 false 1.719,1.063 1.365,1.844 false 1.833,1.052 2.208,1.823 false 1.938,1.063 2.698,1.813 false 0.073,0.104 0.385,0.302 0.313,0.198 10 false *a 0.333,0.958 0.75,1.188 0.417,0.229 10 false A47 0.625,1.865 1.094,2.073 0.469,0.208 10 false CLK- 0.719,0.188 1.188,0.396 0.469,0.208 10 false CLK+ 1.188,0.177 1.656,0.385 0.469,0.208 10 false REQ+ 1.906,0.156 2.375,0.365 0.469,0.208 10 false MTH+ 2.458,0.167 2.927,0.375 0.469,0.208 10 false HTM+ 1.167,1.875 1.635,2.083 0.469,0.208 10 false REQ- 2.094,1.865 2.563,2.073 0.469,0.208 10 false MTH- 2.615,1.854 3.083,2.063 0.469,0.208 10 false HTM-

A379053E13
1.271,2.781 1.688,3.031 0.417,0.25 1.885,2.656 1.531,2.302 false 1.885,2.427 1.583,2.302 false 1.906,1.906 1.531,2.25 false 1.948,2.125 1.583,2.25 false 1.396,2.302 1.031,2.677 false 1.344,2.302 0.938,2.427 false 1.396,2.24 0.969,1.833 false 1.344,2.24 0.938,2.063 false 0.115,0.094 0.427,0.292 0.313,0.198 10 false *b 1.344,2.823 1.885,3.031 0.542,0.208 10 false A72 0.552,1.719 1.01,1.917 0.458,0.198 10 false HTM+ 0.552,1.958 1.01,2.156 0.458,0.198 10 false HTM- 0.542,2.385 1,2.583 0.458,0.198 10 false CLK+ 0.656,2.615 1.115,2.813 0.458,0.198 10 false CLK- 1.969,1.813 2.427,2.01 0.458,0.198 11 false MTH+ 1.979,2.031 2.438,2.229 0.458,0.198 11 false MTH- 1.938,2.354 2.396,2.552 0.458,0.198 10 false REQ- 1.938,2.635 2.396,2.833 0.458,0.198 10 false REQ+

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Switch Condition Specified Condition
A47-8 (HTM+) - A72-24 (HTM+) Power switch off Below 1 Ω
A47-18 (HTM-) - A72-25 (HTM-) Power switch off Below 1 Ω
A47-7 (MTH+) - A72-23 (MTH+) Power switch off Below 1 Ω
A47-17 (MTH-) - A72-22 (MTH-) Power switch off Below 1 Ω
A47-6 (REQ+) - A72-31 (REQ+) Power switch off Below 1 Ω
A47-16 (REQ-) - A72-30 (REQ-) Power switch off Below 1 Ω
A47-5 (CLK+) - A72-33 (CLK+) Power switch off Below 1 Ω
A47-15 (CLK-) - A72-32 (CLK-) Power switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Switch Condition Specified Condition
A47-8 (HTM+) or A72-24 (HTM+) - Body ground and other terminals Power switch off 10 kΩ or higher
A47-18 (HTM-) or A72-25 (HTM-) - Body ground and other terminals Power switch off 10 kΩ or higher
A47-7 (MTH+) or A72-23 (MTH+) - Body ground and other terminals Power switch off 10 kΩ or higher
A47-17 (MTH-) or A72-22 (MTH-) - Body ground and other terminals Power switch off 10 kΩ or higher
A47-6 (REQ+) or A72-31 (REQ+) - Body ground and other terminals Power switch off 10 kΩ or higher
A47-16 (REQ-) or A72-30 (REQ-) - Body ground and other terminals Power switch off 10 kΩ or higher
A47-5 (CLK+) or A72-33 (CLK+) - Body ground and other terminals Power switch off 10 kΩ or higher
A47-15 (CLK-) or A72-32 (CLK-) - Body ground and other terminals Power switch off 10 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Inverter with Converter Assembly)
*b Rear view of wire harness connector
(to Hybrid Vehicle Control ECU)


e.

Connect the cable to the negative (-) auxiliary battery terminal.


f.

Turn the power switch on (IG).


g.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A47-8 (HTM+) or A72-24 (HTM+) - Body ground Power switch on (IG) Below 1 V
A47-18 (HTM-) or A72-25 (HTM-) - Body ground Power switch on (IG) Below 1 V
A47-7 (MTH+) or A72-23 (MTH+) - Body ground Power switch on (IG) Below 1 V
A47-17 (MTH-) or A72-22 (MTH-) - Body ground Power switch on (IG) Below 1 V
A47-6 (REQ+) or A72-31 (REQ+) - Body ground Power switch on (IG) Below 1 V
A47-16 (REQ-) or A72-30 (REQ-) - Body ground Power switch on (IG) Below 1 V
A47-5 (CLK+) or A72-33 (CLK+) - Body ground Power switch on (IG) Below 1 V
A47-15 (CLK-) or A72-32 (CLK-) - Body ground Power switch on (IG) Below 1 V


NOTICE:

Turning the power switch on (IG) with the hybrid vehicle control ECU and inverter with converter assembly connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



h.

Turn the power switch off.


i.

Disconnect the cable from the negative (-) auxiliary battery terminal.


j.

Connect the hybrid vehicle control ECU connector.


k.

Connect the inverter with converter assembly connector.



OK

16.CHECK HYBRID VEHICLE CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.CHECK HYBRID VEHICLE CONTROL ECU
a.

Disconnect connector A72 from the hybrid vehicle control ECU.


b.
U183240E02
1.344,1.792 0.51,1.083 false 1.385,1.792 1.094,1.083 false 1.521,1.792 1.75,1.073 false 1.573,1.792 2.375,1.094 false 0.688,2.365 1.333,1.865 false 1.198,2.354 1.385,1.854 false 1.75,2.375 1.521,1.854 false 2.292,2.354 1.573,1.854 false 0.208,0.885 0.594,1.042 0.385,0.156 10 false HTM- 0.781,0.885 1.188,1.042 0.406,0.156 10 false HTM+ 0.385,2.396 0.771,2.552 0.385,0.156 10 false CLK+ 1.021,2.385 1.406,2.542 0.385,0.156 10 false CLK- 1.604,2.396 2.01,2.552 0.406,0.156 10 false REQ+ 2.198,2.396 2.625,2.552 0.427,0.156 10 false REQ- 1.573,0.875 1.979,1.031 0.406,0.156 10 false MTH+ 2.208,0.896 2.615,1.052 0.406,0.156 10 false MTH- 0.115,0.083 0.292,0.24 0.177,0.156 10 false *a 1.354,2.677 1.625,2.844 0.271,0.167 10 false A72

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A72-24 (HTM+) - A72-25 (HTM-) Power switch off 80 to 170 Ω
A72-23 (MTH+) - A72-22 (MTH-) Power switch off 80 to 170 Ω
A72-31 (REQ+) - A72-30 (REQ-) Power switch off 80 to 170 Ω
A72-33 (CLK+) - A72-32 (CLK-) Power switch off 80 to 170 Ω


Text in Illustration
*a Component without harness connected
(Hybrid Vehicle Control ECU)


c.

Connect the hybrid vehicle control ECU connector.



OK

17.CHECK CONNECTOR CONNECTION CONDITION (GENERATOR RESOLVER CONNECTOR)

NG

17.CHECK CONNECTOR CONNECTION CONDITION (GENERATOR RESOLVER CONNECTOR)

OK

18.CHECK CONNECTOR CONNECTION CONDITION (MOTOR RESOLVER CONNECTOR)

NG

CONNECT SECURELY

18.CHECK CONNECTOR CONNECTION CONDITION (MOTOR RESOLVER CONNECTOR)

OK

19.CHECK FOR INTERMITTENT PROBLEMS

NG

CONNECT SECURELY

19.CHECK FOR INTERMITTENT PROBLEMS

OK

20.SIMULATION TEST

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

20.SIMULATION TEST
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (READY) and wait for 5 seconds or more.


c.

Perform a road test according to the freeze frame data "Vehicle Spd" for approximately 10 minutes.


d.

Enter the following menus: Powertrain / Hybrid Control / DTC.


e.

Check if DTCs are output.

Result:
Result Proceed to
P0A78-113 is output. A
P0A78-113 is not output. B


HINT:

If the connector engagement check and cleaning caused the condition to return to normal, DTCs will not be output.



f.

Turn the power switch off.



A

REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS

B

END

21.CHECK CONNECTOR CONNECTION CONDITION (GENERATOR RESOLVER CONNECTOR)

OK

22.INSPECT HYBRID VEHICLE TRANSAXLE ASSEMBLY (GENERATOR RESOLVER)

NG

CONNECT SECURELY

22.INSPECT HYBRID VEHICLE TRANSAXLE ASSEMBLY (GENERATOR RESOLVER)

OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG

23.CHECK CONNECTOR CONNECTION CONDITION (MOTOR RESOLVER CONNECTOR)

OK

24.INSPECT HYBRID VEHICLE TRANSAXLE ASSEMBLY (MOTOR RESOLVER)

NG

CONNECT SECURELY

24.INSPECT HYBRID VEHICLE TRANSAXLE ASSEMBLY (MOTOR RESOLVER)

OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG

25.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - PCU FUSE)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect connector A47 from the inverter with converter assembly.


c.
U158866E02
2.115,0.99 2,0.292 false 2.271,0.99 2.448,0.292 false 1.833,0.083 2.146,0.271 0.313,0.188 10 false +B2 2.396,0.083 2.708,0.271 0.313,0.188 10 false +B 0.177,0.083 0.49,0.271 0.313,0.188 10 false *a 0.344,1.073 0.667,1.26 0.323,0.188 10 false A47

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A47-10 (+B) - Body ground Power switch off 10 kΩ or higher
A47-9 (+B2) - Body ground Power switch off 10 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Inverter with Converter Assembly)


d.

Connect the inverter with converter assembly connector.



OK

26.REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS

NG

27.REPAIR OR REPLACE HARNESS OR CONNECTOR
26.REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS

NEXT

REPLACE FUSE (PCU)

27.REPAIR OR REPLACE HARNESS OR CONNECTOR

NEXT

REPLACE FUSE (PCU)

28.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MOTOR CABLE (FOR MG1) CONNECTION CONDITION)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the inverter with converter assembly (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>INVERTER WITH CONVERTER>COMPONENTS).


c.
A258652E02
2.271,0.51 2.438,0.688 0.167,0.177 10 true A 1.604,1.906 1.76,2.104 0.156,0.198 10 true A 1.083,2.552 1.208,2.719 0.125,0.167 10 true B 0.938,2.719 1.063,2.885 0.125,0.167 10 false B 0.813,2.917 0.958,3.115 0.146,0.198 10 true B

Check that the bolts for the motor cable (for MG1) are tightened to the specified torque, the motor cable (for MG1) is connected securely, and there are no contact problems.

Specified Condition:
Bolt A:

T=19.5 N*m (199 kgf*cm, 14 ft.*lbf)

Bolt B:

T=10 N*m (102 kgf*cm, 7 ft.*lbf)


NOTICE:
·

Make sure that the tightening torque of the bolt A is between 13.5 and 25 N*m (138 and 255 kgf*cm, 10 and 18 ft.*lbf).

·

Make sure that the tightening torque of the bolt B is between 8 and 12 N*m (82 and 122 kgf*cm, 71 and 106 in.*lbf).




d.

Disconnect the motor cable (for MG1) from the hybrid vehicle transaxle assembly.


e.

Check for arc marks at the terminals for the motor cable (for MG1).

Result:
Result Proceed to
The terminals are connected securely and there are no contact problems. There are no arc marks. A
The terminals are not connected securely and there is a contact problem. There are arc marks. B
The terminals are not connected securely and there is a contact problem. There are no arc marks. C
The terminals are connected securely and there are no contact problems. There are arc marks. B



f.

Connect the motor cable (for MG1) to the hybrid vehicle transaxle assembly.


g.

Install the inverter with converter assembly.



A

29.CHECK MOTOR CABLE (FOR MG1)

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY

29.CHECK MOTOR CABLE (FOR MG1)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.




c.
U158938E01
0.182,0.149 0.388,0.376 0.206,0.227 10 *a 0.457,0.94 0.663,1.166 0.206,0.227 10 *1 1.082,2.017 1.287,2.180 0.206,0.163 10 W 2.223,2.017 2.373,2.175 0.150,0.158 10 V 1.696,2.017 1.902,2.185 0.206,0.168 10 U 0.909,1.001 0.69,1.001 false 1.365,1.792 1.173,1.992 false 1.756,1.798 1.756,1.972 false 2.154,1.789 2.281,1.98 false 2.769,1.364 2.958,1.527 0.190,0.163 10 a2 0.201,2.607 0.406,2.833 0.206,0.227 10 *b 2.874,2.767 3.080,2.993 0.206,0.227 10 *1 1.444,4.129 1.326,4.275 false 1.792,4.121 1.792,4.264 false 2.163,4.123 2.246,4.272 false 2.857,3.546 3.054,3.709 0.197,0.163 10 a1 2.216,4.286 2.422,4.449 0.206,0.163 10 V 1.253,4.286 1.447,4.444 0.194,0.158 10 W 1.731,4.286 1.936,4.453 0.206,0.168 10 U 2.518,3.038 2.843,2.857 false

Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.


Standard Resistance:
Tester Connection Switch Condition Specified Condition
a2-1 (W) - Body ground and shield ground Power switch off 100 MΩ or higher
a2-2 (U) - Body ground and shield ground Power switch off 100 MΩ or higher
a2-3 (V) - Body ground and shield ground Power switch off 100 MΩ or higher


Text in Illustration
*1 Shield ground
*a Motor Cable (for MG1)
(Inverter with Converter Assembly Side)
*b Motor Cable (for MG1)
(Hybrid Vehicle Transaxle Assembly Side)

NOTICE:

Wrap the terminal of the motor cable (for MG1) with insulating tape to prevent them from coming into contact with body ground



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
a2-1 (W) - a1-1 (W) Power switch off Below 1 Ω
a2-2 (U) - a1-2 (U) Power switch off Below 1 Ω
a2-3 (V) - a1-3 (V) Power switch off Below 1 Ω
a2-1 (W) - a1-2 (U) Power switch off 100 MΩ or higher
a2-2 (U) - a1-3 (V) Power switch off 100 MΩ or higher
a2-3 (V) - a1-1 (W) Power switch off 100 MΩ or higher



e.

Install the motor cable.



OK

NG

30.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MOTOR CABLE (FOR MG2) CONNECTION CONDITION)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A258653E02
1.021,2.969 1.188,3.167 0.167,0.198 10 true B 2.219,1.802 2.458,1.99 0.24,0.188 10 true A 0.438,0.51 0.583,0.708 0.146,0.198 10 true A 0.99,3.208 1.156,3.396 0.167,0.188 10 true B 0.948,3.417 1.125,3.615 0.177,0.198 10 true B

Check that the bolts for the motor cable (for MG2) are tightened to the specified torque, the motor cable (for MG2) is connected securely, and there are no contact problems.

Specified Condition:
Bolt A:

T=19.5 N*m (199 kgf*cm, 14 ft.*lbf)

Bolt B:

T=10 N*m (102 kgf*cm, 7 ft.*lbf)


NOTICE:
·

Make sure that the tightening torque of the bolt A is between 13.5 and 25 N*m (138 and 255 kgf*cm, 10 and 18 ft.*lbf).

·

Make sure that the tightening torque of the bolt B is between 8 and 12 N*m (82 and 122 kgf*cm, 71 and 106 in.*lbf).




c.

Disconnect the motor cable (for MG2) from the hybrid vehicle transaxle assembly.


d.

Check for arc marks at the terminals for the motor cable (for MG2).

Result:
Result Proceed to
The terminals are connected securely and there are no contact problems. There are no arc marks. A
The terminals are not connected securely and there is a contact problem. There are arc marks. B
The terminals are not connected securely and there is a contact problem. There are no arc marks. C
The terminals are connected securely and there are no contact problems. There are arc marks. B



e.

Connect the motor cable (for MG2) to the hybrid vehicle transaxle assembly.



A

31.CHECK MOTOR CABLE (FOR MG2)

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY

31.CHECK MOTOR CABLE (FOR MG2)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.




c.
U158939E01
0.182,0.141 0.388,0.367 0.206,0.227 10 *a 0.457,0.931 0.663,1.158 0.206,0.227 10 *1 1.082,2.018 1.287,2.181 0.206,0.163 10 W 2.223,2.018 2.373,2.177 0.150,0.158 10 V 1.696,2.018 1.902,2.186 0.206,0.168 10 U 0.909,0.992 0.69,0.992 false 1.365,1.793 1.173,1.993 false 1.756,1.8 1.756,1.973 false 2.154,1.791 2.281,1.981 false 2.769,1.356 2.958,1.519 0.190,0.163 10 a4 0.201,2.598 0.406,2.825 0.206,0.227 10 *b 0.326,3.27 0.532,3.497 0.206,0.227 10 *1 1.445,4.344 1.326,4.421 false 1.792,4.335 1.792,4.41 false 2.163,4.338 2.246,4.418 false 2.857,3.537 3.054,3.700 0.197,0.163 10 a3 1.236,4.432 1.442,4.595 0.206,0.163 10 W 2.223,4.432 2.417,4.590 0.194,0.158 10 U 1.731,4.432 1.936,4.599 0.206,0.168 10 V 0.832,3.171 0.508,3.353 false

Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.


Standard Resistance:
Tester Connection Switch Condition Specified Condition
a4-1 (W) - Body ground and shield ground Power switch off 100 MΩ or higher
a4-2 (U) - Body ground and shield ground Power switch off 100 MΩ or higher
a4-3 (V) - Body ground and shield ground Power switch off 100 MΩ or higher


Text in Illustration
*1 Shield ground
*a Motor Cable (for MG2)
(Inverter with Converter Assembly Side)
*b Motor Cable (for MG2)
(Hybrid Vehicle Transaxle Assembly Side)

NOTICE:

Wrap the terminal of the motor cable (for MG2) with insulating tape to prevent them from coming into contact with body ground



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
a4-1 (W) - a3-1 (W) Power switch off Below 1 Ω
a4-2 (U) - a3-3 (U) Power switch off Below 1 Ω
a4-3 (V) - a3-2 (V) Power switch off Below 1 Ω
a4-1 (W) - a3-3 (U) Power switch off 100 MΩ or higher
a4-2 (U) - a3-2 (V) Power switch off 100 MΩ or higher
a4-3 (V) - a3-1 (W) Power switch off 100 MΩ or higher



e.

Install the motor cable.



OK

NG