The hybrid vehicle control ECU monitors its internal operation and detects the following malfunction.
| DTC No. | INF Code | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| P3000 | 603 | The hybrid vehicle control ECU detects a HV battery cooling system error signal. | ·
Hybrid vehicle control ECU ·
HV battery ·
Battery smart unit |
| DTC No. | Data List |
|---|---|
| P3000-603 | ·
Temp of Batt TB1 to TB3 ·
Inhaling Air Temp ·
Ambient Temperature ·
Power Resource IB ·
State of Charge (All Bat) ·
Cooling Fan Mode1 ·
Cooling Fan 0 ·
Hot Temperature Time |
The following items can be helpful when performing repairs:
Vehicle Spd
Engine Run Time
Ready Signal
When disposing of an HV battery, make sure to return it through an authorized collection agent who is capable of handling it safely. If the HV battery is returned via the manufacturer specified route, it will be returned properly and in a safe manner by an authorized collection agent.
After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.
Drive the vehicle for approximately 10 minutes according to the freeze frame data items "Vehicle Spd", "Temp of Batt TB1 to TB3", "Inhaling Air Temp", "Ambient Temperature" and "Power Resource IB".
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / DTC.
Check if DTCs are output.
| Result | Proceed to |
|---|---|
| P3000-603 only is output. | A |
| DTCs other than P3000-603 are also output. | B |
Turn the power switch off.
A
B
(See pageEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>DIAGNOSTIC TROUBLE CODE CHART)
| *a | Intake Port |
Check the HV battery cooling system intake port for blockage.
If anything is blocking the HV battery cooling system intake port, remove it.
Clean the battery cooling blower filter.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY BLOWER>INSPECTION
NEXT
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Read the freeze frame data of DTC P3000-603.
| *a | Freeze Frame Data Recorded |
| *b | DTC Stored |
| *c | Time |
Although freeze frame data is recorded before and after a DTC is stored, for this step it is only necessary to read the freeze flame data recorded before "0s" (when the DTC was stored).
| Result | Proceed to |
|---|---|
| Other than below | A |
| The sum of the value of each hybrid battery block voltage ("Battery Block Vol-V01 to V10") is less than the value of "VL-Voltage before Boosting" by 10 V or more. | B |
Turn the power switch off.
A
B
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Read the freeze frame data of DTC P3000-603.
Although freeze frame data is recorded before and after a DTC is stored, for this step it is only necessary to read the freeze flame data recorded at "0s" (when the DTC was stored).
| Result | Proceed to |
|---|---|
| Other than below | A |
| The value of any of "Temp of Batt TB1 to TB3" is 80°C (176°F) or more. | B |
Turn the power switch off.
A
B
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Data List / "Temp of Batt TB1 to TB3".
According to the display on the intelligent tester, read the Data List and check that the value of each "Temp of Batt TB1 to TB3" is 40°C (104°F) or less.
If the value of any of "Temp of Batt TB1 to TB3" is more than 40°C (104°F), turn the power switch off and wait until the values to decrease to 40°C (104°F) or less before continuing this procedure.
Enter the following menus: Powertrain / Hybrid Control / Data List / "Battery Block Vol - V01 to V10".
According to the display on the intelligent tester, read the Data List and check the value of each "Battery Block Vol-V01 to V10" with the power switch on (IG).
| *a | Battery Block Vol -V01 | *b | Battery Block Vol -V02 |
| *c | Battery Block Vol -V03 | *d | Battery Block Vol -V04 |
| *e | Battery Block Vol -V05 | *f | Battery Block Vol -V06 |
| *g | Battery Block Vol -V07 | *h | Battery Block Vol -V08 |
| *i | Battery Block Vol -V09 | *j | Battery Block Vol -V10 |
| Result | Proceed to |
|---|---|
| Other than below | A |
| The difference between the lowest and highest HV battery block voltage is 0.3 V or more. | B |
Turn the power switch off.
A
B
NEXT
NEXT