Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › BATTERY BLOWER › 2014.12–2017.06
RM2170E _51 Engine / Hybrid System _057004 HYBRID / BATTERY CONTROL _0277937 BATTERY BLOWER G

HYBRID / BATTERY CONTROL  BATTERY BLOWER  INSPECTION  


PROCEDURE

Hide G9230 1.INSPECT BATTERY COOLING BLOWER ASSEMBLY

a.

Inspect the battery cooling blower filter.

HINT:
·

It is not necessary to remove the front floor cover LH to inspect the battery cooling blower filter.

·

Inspect the battery cooling blower filter with the battery cooling blower assembly installed to the vehicle.



i.
A369917E01
0.216,0.954 0.393,1.112 0.177,0.158 10 *1 0.409,1.048 1.1,1.048 false

Inspect the battery cooling blower filter.

Text in Illustration
*1 Battery Cooling Blower Filter

Standard:

No clogs or damage.


NOTICE:

If the battery cooling blower filter is damaged, replace the battery cooling blower filter.




b.

Clean the battery cooling blower filter.

NOTICE:

If the battery cooling blower filter is excessively dirty, replace it.


i.

When not removed from the vehicle:

1.
A369887

Clean the battery cooling blower filter by hand or using a vacuum cleaner.

NOTICE:
·

Do not use compressed air.

·

Do not use water or any other liquids when cleaning the filter.

·

Do not use a wire brush or scrubber.

·

Do not disassemble the battery cooling blower assembly.

·

Do not allow any foreign matter to enter the battery cooling blower assembly.



HINT:
·

It is not necessary to remove the front floor cover LH to clean the battery cooling blower filter.

·

Clean the battery cooling blower filter with the battery cooling blower assembly installed to the vehicle.





ii.

When removed from the vehicle:

NOTICE:
·

This procedure is for type B only.

·

As type A is a non-reusable part, do not perform this procedure.



1.
A387272

Clean the battery cooling blower filter by blowing compressed air as shown in the illustration.

NOTICE:
·

Do not use water or any other liquids when cleaning the battery cooling blower filter. Use only compressed air.

·

To prevent damage to the battery cooling blower filter, do not use a wire brush or other tool.

·

Do not clean the battery cooling blower filter with it installed to the vehicle.

·

Keep the air blow gun at least 30 mm (1.18 in.) away from the battery cooling blower filter.

·

Blow compressed air through the rear side of battery cooling blower filter.






c.

Replace the battery cooling blower filter.

HINT:

Replace the battery cooling blower filter with the battery cooling blower assembly installed to the vehicle.


i.

Remove the front floor cover LH.



ii.

Type A:

1.

Remove the battery cooling blower filter from the battery cooling blower assembly.

A369844C03
5.219,0.75 6.167,0.75 true 6.25,0.646 6.563,0.969 0.313,0.323 10 false *1
*1 Battery Cooling Blower Filter - -
V100144

Depression - -


HINT:
·

The battery cooling blower filter is secured with double-sided tape.

·

Place a hand in the depression of the battery cooling blower assembly and remove the battery cooling blower filter.



2.

Wipe off any tape adhesive residue of the battery cooling blower assembly with cleaner.

3.

Remove the peeling paper from the face of a new battery cooling blower filter.

HINT:

After removing the peeling paper, keep the exposed adhesive free from foreign matter.


4.

Install the battery cooling blower filter to the battery cooling blower assembly.

HINT:

Press the battery cooling blower filter firmly to install it.




iii.

Type B:

1.

Disengage the 2 claws to remove the battery cooling blower filter from the battery cooling blower assembly.

A387270C02
5.167,1.063 6.24,1.063 true 6.333,0.99 6.646,1.188 0.313,0.198 10 false *1
*1 Battery Cooling Blower Filter - -


2.

Engage the 2 claws to install the battery cooling blower filter to the battery cooling blower assembly.

NOTICE:

After installing the battery cooling blower filter, make sure that each claw is securely engaged.




iv.

Install the front floor cover LH.