Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › 2011.12–2014.12
RM2170E _51 Engine / Hybrid System _057004 HYBRID / BATTERY CONTROL _0277924 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P3004-133  High Voltage Power Resource  


DESCRIPTION

The power management control ECU monitors its internal operation, it will set DTCs and perform fail-safe control when it detects the following malfunctions.

DTC No. INF Code DTC Detection Condition Trouble Area
P3004 133 A high-voltage wiring system error signal is detected in the power management control ECU
·

Power management control ECU

·

HV battery junction block assembly

·

Battery smart unit

·

Wire harness or connector



WIRING DIAGRAM

A388953E03
1.885,1.063 2.198,1.26 0.313,0.198 10 false IB 1.792,1.688 2.104,1.885 0.313,0.198 10 false VIB 1.792,2.333 2.104,2.531 0.313,0.198 10 false GIB 2.135,0.969 2.448,1.167 0.313,0.198 10 false 3 2.135,1.604 2.448,1.802 0.313,0.198 10 false 1 2.146,2.229 2.458,2.427 0.313,0.198 10 false 2 4.927,0.969 5.24,1.167 0.313,0.198 10 false 5 4.938,1.615 5.25,1.813 0.313,0.198 10 false 6 4.885,2.219 5.198,2.417 0.313,0.198 10 false 12 5.156,1.063 5.469,1.26 0.313,0.198 10 false IB 5.146,1.688 5.458,1.885 0.313,0.198 10 false VIB 5.135,2.333 5.448,2.531 0.313,0.198 10 false GIB 0.542,2.896 0.854,3.094 0.313,0.198 10 false d2 0.771,2.896 2.833,3.333 2.063,0.438 10 false Battery Current Sensor (Hybrid Battery Junction Block Assembly) 4.896,2.896 5.208,3.094 0.313,0.198 10 false d1 5.167,2.896 6.573,3.188 1.406,0.292 10 false Battery Smart Unit

CAUTION / NOTICE / HINT

CAUTION:
·

Before inspecting the high-voltage system, take safety precautions to prevent electrical shocks, such as wearing insulated gloves and removing the service plug grip. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·

After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION

HINT:

At least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Drive the vehicle for approximately 10 minutes according to the freeze frame data items "Vehicle Spd", "Accelerator Degree" and "Power Resource IB".



PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / DTC.


d.

Check if DTCs are output.

Result:
Result Proceed to
P3004-133 only is output. A
DTCs other than P3004-133 is output. B



e.

Turn the power switch off.



A

2.READ VALUE USING INTELLIGENT TESTER (POWER RESOURCE IB)

B

2.READ VALUE USING INTELLIGENT TESTER (POWER RESOURCE IB)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch to on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Data List / Power Resource IB.


d.

Read the Data List.

Result:
Result Proceed to
The value of Power Resource IB is between -4 A and 4 A A
Other than above B



e.

Turn the power switch off.



A

B

3.CHECK HARNESS AND CONNECTOR (HV BATTERY JUNCTION BLOCK ASSEMBLY - BATTERY SMART UNIT)
3.CHECK HARNESS AND CONNECTOR (HV BATTERY JUNCTION BLOCK ASSEMBLY - BATTERY SMART UNIT)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 hybrid battery shield sub-assembly.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY SMART UNIT>REMOVAL


c.

Remove the No. 2 hybrid battery shield sub-assembly.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV RELAY ASSEMBLY>REMOVAL


d.

Disconnect only the d1 connector of the battery smart unit.


e.
A287103E01
2.177,0.906 2.417,1.083 0.24,0.177 2.229,0.927 2.542,1.125 0.313,0.198 10 d2

Disconnect the d2 battery current sensor connector from the HV battery junction block assembly.


f.
A260183E03
0.573,1.542 1,1.802 0.427,0.26 0.552,3.563 0.979,3.823 0.427,0.26 1.594,1.688 2.271,1.156 false 1.969,3.76 2.583,3.708 false 1.458,1.667 1.104,1.146 false 1.51,3.844 0.885,3.188 false 1.438,1.844 1.063,2.156 false 1.781,3.75 2.427,3.188 false 0.24,0.958 0.469,1.156 0.229,0.198 10 *a 0.24,2.698 0.469,2.896 0.229,0.198 10 *b 2.333,1.083 2.604,1.271 0.271,0.188 10 IB 2.625,3.646 2.854,3.833 0.229,0.188 10 IB 0.875,1.083 1.188,1.292 0.313,0.208 10 VIB 0.656,3.094 0.969,3.271 0.313,0.177 10 VIB 0.854,2.125 1.146,2.323 0.292,0.198 10 GIB 2.448,3.083 2.74,3.281 0.292,0.198 10 GIB 0.729,1.594 0.979,1.781 0.25,0.188 10 d1 0.698,3.615 0.927,3.76 0.229,0.146 10 d2

Measure the resistance according to the value(s) in the tables below.

Standard Resistance (Check for Open):
Tester Connection Switch Condition Specified Condition
d1-5 (IB) - d2-3 (IB) Power switch off Below 1 Ω
d1-12 (GIB) - d2-2 (GIB) Power switch off Below 1 Ω
d1-6 (VIB) - d2-1 (VIB) Power switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Switch Condition Specified Condition
d1-5 (IB) or d2-3 (IB) - Body ground and other terminals Power switch off 10 kΩ or higher
d1-12 (GIB) or d2-2 (GIB) - Body ground and other terminals Power switch off 10 kΩ or higher
d1-6 (VIB) or d2-1 (VIB) - Body ground and other terminals Power switch off 10 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to Battery Smart Unit)
*b Front view of wire harness connector
(to HV Battery Junction Block Assembly)

HINT:

Because the battery harness is not available as a supply part, if the harness cannot be repaired, replace the HV battery assembly.



g.

Connect the battery smart unit connector.


h.

Connect the battery current sensor connector to the HV battery junction block assembly.


i.

Install the No. 2 hybrid battery shield sub-assembly.


j.

Install the No. 1 hybrid battery shield sub-assembly.



OK

4.CHECK HV BATTERY JUNCTION BLOCK ASSEMBLY (BATTERY CURRENT SENSOR (IB))

NG

REPAIR HARNESS OR CONNECTOR

4.CHECK HV BATTERY JUNCTION BLOCK ASSEMBLY (BATTERY CURRENT SENSOR (IB))
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch to on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 hybrid battery shield sub-assembly.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY SMART UNIT>REMOVAL


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the power switch to on (IG).


e.
A260172C38
1.031,0.146 1.344,0.375 0.313,0.229 0.583,0.448 0.917,0.885 false 0.906,0.969 0.615,1.708 false 0.125,0.125 0.354,0.302 0.229,0.177 10 *a 0.365,0.365 0.698,0.573 0.333,0.208 10 VIB 0.49,1.729 0.885,2.01 0.396,0.281 10 GIB 1.115,0.198 1.375,0.396 0.26,0.198 10 d1
*a Component with harness connected
(Battery Smart Unit)


Using a toyota electrical tester set to 40 V, measure the VIB voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition
d1-6(VIB) - d1-12(GIB) Power switch on (IG)


NOTICE:
·

Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.

·

Be sure to set the toyota electrical tester to 40 V when performing this test.




f.
A260172C39
0.875,0.083 1.302,0.344 0.427,0.26 0.99,0.885 1.781,0.354 false 0.917,0.958 0.625,1.698 false 0.146,0.125 0.375,0.365 0.229,0.24 10 *a 1.844,0.25 2.094,0.49 0.25,0.24 10 IB 0.521,1.74 0.771,1.958 0.25,0.219 10 GIB 1.031,0.146 1.26,0.292 0.229,0.146 10 d1
*a Component with harness connected
(Battery Smart Unit)


Using a toyota electrical tester set to 4 V, measure the IB voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition
d1-5(IB) - d1-12(GIB) Power switch on (IG)


NOTICE:

Be sure to set the toyota electrical tester to 4 V when performing this test.



g.

Compare the measured values of the IB terminal voltage and VIB terminal voltage using the following formula:

IB voltage - VIB Voltage / 2 = less than 0.081 V
IB voltage - VIB Voltage / 2 = -0.081 V or higher

Result:
Result Proceed to
Within the specified range above A
Other than above B



h.

Turn the power switch off.


i.

Disconnect the cable from the negative (-) auxiliary battery terminal.


j.

Install the No. 1 hybrid battery shield sub-assembly.


HINT:

When the power switch is on (IG) the actual current will be approximately 0 A. The following graph shows the relation of the actual output voltage of the battery current sensor terminal IB and actual current used for DTC judgment.

A425433E02
1.75,0.438 2.208,0.635 0.458,0.198 10 false Voltage 4.677,2.156 5.135,2.354 0.458,0.198 10 false Current 1.635,1.208 2.094,1.406 0.458,0.198 10 false VIB/2 3.167,2.656 3.625,2.854 0.458,0.198 10 false -4 A 3.573,2.667 4.031,2.865 0.458,0.198 10 false 0 A 3.927,2.667 4.385,2.865 0.458,0.198 10 false +4 A 0.646,2.802 3.458,3 2.813,0.198 10 false Battery Current Sensor Normal Range 0.656,3.083 3.469,3.281 2.813,0.198 10 false Toyota electrical tester margin of error 0.656,3.354 3.469,3.552 2.813,0.198 10 false Battery current sensor operation malfunction



A

5.REPLACE BATTERY SMART UNIT

B

REPLACE HV BATTERY JUNCTION BLOCK ASSEMBLY

5.REPLACE BATTERY SMART UNIT

NEXT

6.SIMULATION TEST
6.SIMULATION TEST
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / DTC.


d.

Clear the DTCs and freeze frame data.


e.

Drive the vehicle on urban roads for approximately 10 minutes.


f.

Turn the power switch off and wait for 2 minutes or more.


g.

Turn the power switch on (IG) and wait for 30 seconds or more.



NEXT

7.RECONFIRM DTC OUTPUT
7.RECONFIRM DTC OUTPUT
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / DTC.


d.

Read output DTCs.


e.

Turn the power switch off.


Result:
Result Proceed to
DTCs are not output A
P3004-133 is output B



A

COMPLETED

B

REPLACE HV BATTERY JUNCTION BLOCK ASSEMBLY