Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › from 2014.12
RM2170E _51 Engine / Hybrid System _057004 HYBRID / BATTERY CONTROL _0277924 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P3107-214  Lost Communication with Airbag System Control Module  


DESCRIPTION

Refer to the description for DTC P3107-213 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P3107-213).


DTC No. INF Code DTC Detection Condition Trouble Area
P3107 214 Open or short to +B in the communication circuit
·

Wire harness or connector

·

Airbag sensor assembly

·

Hybrid vehicle control ECU



WIRING DIAGRAM

Refer to the wiring diagram for DTC P0AE6-225 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0AE6-225).

Refer to the wiring diagram for DTC P3107-213 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P3107-213).

CAUTION / NOTICE / HINT

HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Turn the power switch on (IG) and wait for 15 seconds or more.



PROCEDURE

1.CHECK DTC OUTPUT (SRS AIRBAG)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Body / SRS Airbag / DTC.


d.

Check if DTCs are output.


Result:
Result Proceed to
Airbag system DTCs are not output. A
Airbag system DTCs are output. B


e.

Turn the power switch off.



A

2.CHECK AIRBAG SENSOR ASSEMBLY (CHECK WAVEFORM)

B

2.CHECK AIRBAG SENSOR ASSEMBLY (CHECK WAVEFORM)

A

3.CLEAR DTC

B

6.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)
3.CLEAR DTC

NEXT

4.CHECK DTC OUTPUT (HYBRID CONTROL)
4.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / DTC.


d.

Check if DTCs are output.

Result:
Result Proceed to
P3107-214 is not output. A
P3107-214 is output again. B



e.

Turn the power switch off.



A

5.CHECK FOR INTERMITTENT PROBLEMS

B

5.CHECK FOR INTERMITTENT PROBLEMS

OK

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

6.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)

OK

7.CHECK CONNECTOR CONNECTION CONDITION (AIRBAG SENSOR ASSEMBLY CONNECTOR)

NG

CONNECT SECURELY

7.CHECK CONNECTOR CONNECTION CONDITION (AIRBAG SENSOR ASSEMBLY CONNECTOR)
a.
U158888E02
1.208,1.042 1.479,1.688 false 0.177,0.073 0.427,0.302 0.25,0.229 10 false *a 1.281,1.708 1.854,1.938 0.573,0.229 10 false GSW2 0.958,0.375 1.25,0.531 0.292,0.156 10 false G18

Check the connector connections and contact pressure of the relevant terminals for the airbag sensor assembly connectors.

Text in Illustration
*a Component with harness connected
(Airbag Sensor Assembly)

OK:

The connectors are connected securely and there are no contact pressure problems.




OK

8.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - AIRBAG SENSOR ASSEMBLY)

NG

CONNECT SECURELY

8.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - AIRBAG SENSOR ASSEMBLY)
a.

Disconnect connector G81 from the hybrid vehicle control ECU.


b.

Disconnect connector G18 from the airbag sensor assembly.


c.
U183650E02
2.604,1.906 2.208,2.198 false 1.24,3.958 1.74,4.333 false 0.021,0.031 0.292,0.229 0.271,0.198 10 false *a 0.042,2.469 0.313,2.667 0.271,0.198 10 false *b 1.958,1.802 2.25,1.969 0.292,0.167 10 false G81 0.396,3.823 0.698,3.99 0.302,0.167 10 false G18 1.833,2.167 2.302,2.365 0.469,0.198 10 false ABFS 1.771,4.281 2.406,4.5 0.635,0.219 10 false GSW2

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Switch Condition Specified Condition
G81-14 (ABFS) - G18-14 (GSW2) Power switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Switch Condition Specified Condition
G81-14 (ABFS) or G18-14 (GSW2) - Body ground and other terminals Power switch off 10 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to Hybrid Vehicle Control ECU)
*b Rear view of wire harness connector
(to Airbag Sensor Assembly)

HINT:

As necessary, check that there is no short to power supply wires when performing the above wire harness inspection.



d.

Connect the airbag sensor assembly connector.


e.

Connect the hybrid vehicle control ECU connector.



OK

9.CHECK HYBRID CONTROL CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HYBRID CONTROL CONTROL ECU
a.
U158887E03
0.094,0.031 0.344,0.25 0.25,0.219 10 false *a 0.49,1.365 0.781,1.531 0.292,0.167 10 false G18

Disconnect connector G18 from the airbag sensor assembly.

Text in Illustration
*a Component without harness connected
(Airbag Sensor Assembly)


b.

Turn the power switch on (IG).


c.
U183251E02
2.563,1.771 2.51,2.531 false 2.302,2.563 2.792,2.74 0.49,0.177 10 false ABFS 0.135,0.052 0.292,0.229 0.156,0.177 10 false *a 2.5,0.969 2.802,1.146 0.302,0.177 10 false G81

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G81-14 (ABFS) - Body ground Power switch on (IG) 11 to 14 V


Text in Illustration
*a Component with harness connected
(Hybrid Vehicle Control ECU)

NOTICE:

Turning the power switch on (IG) with the airbag sensor assembly connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



d.

Turn the power switch off.


e.

Connect the airbag sensor assembly connector.



OK

NG