The drive start control is controlled by the hybrid vehicle control ECU.
If the hybrid vehicle control ECU determines that the shift lever and accelerator pedal are operated abnormally, driving torque is restricted and, when necessary, a warning is displayed on the combination meter assembly.
Even if the accelerator pedal position is maintained, the engine output may increase when driving uphill and decrease when driving downhill. This is due to the drive start control controlling the driving torque, and is not a malfunction.
Interview the customer to confirm the problem.
| Result | Proceed to |
|---|---|
| Hunting | A |
| Hesitation/poor acceleration | B |
A
B
Check if the customer operated the vehicle in a way that would cause the drive start control to operate.
Drive Start Control Activation Conditions
Condition 1 (Reverse control)
The shift lever is in R.
The accelerator pedal is depressed.
Driving torque is restricted.
The shift lever is moved to any position other than R.
The accelerator pedal is released.
Condition 2 (Shift control A)
The shift lever is moved from P to any forward position (D or B) or R.
The accelerator pedal is open by approximately 1/5 or more.
Driving torque is restricted.
The shift lever is in P or N.
The accelerator pedal is released.
Condition 3 (Shift control B)
The shift lever is moved from R to any forward position (D or B), any forward position (D or B) to R, or N to R.
The accelerator pedal is open by approximately 1/5 or more.
Driving torque is restricted.
The shift lever is in P or N.
The accelerator pedal is released.
During reverse control or shift control, driving torque is adjusted based on the road gradient and steering angle.
| Result | Proceed to |
|---|---|
| Performed | A |
| Not performed | B |
A
B
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Enter the following menus: System Select / Utility / All Codes.
Check for DTCs.
| Result | Proceed to |
|---|---|
| No DTCs are output. | A |
| DTCs are output | B |
Turn the power switch off.
A
B
Connect the intelligent tester to the DLC3.
Turn the power switch on (READY).
Enter the following menus: Chassis / ABS/VSC/TRC / Data List / FR Wheel Speed, FL Wheel Speed, RR Wheel Speed and RL Wheel Speed.
Read the value displayed on the intelligent tester.
| Tester Display | Measurement Item / Range | Normal Condition |
|---|---|---|
| FR Wheel Speed | Front speed sensor RH
Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) |
When driving at constant speed:
No large fluctuations |
| FL Wheel Speed | Front speed sensor LH
Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) |
When driving at constant speed:
No large fluctuations |
| RR Wheel Speed | Rear speed sensor RH
Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) |
When driving at constant speed:
No large fluctuations |
| RL Wheel Speed | Rear speed sensor LH
Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) |
When driving at constant speed:
No large fluctuations |
| Tester Display | Condition | Specified Condition |
|---|---|---|
| FR Wheel Speed
FL Wheel Speed RR Wheel Speed RL Wheel Speed |
Vehicle stopped, engine running | 0 km/h (0 mph) |
| Vehicle being driven at constant speed between 16 to 64 km/h (10 to 40 mph) | No large fluctuations when driving at a constant speed |
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Data can be captured relatively easily by using the snapshot function in the Data List. Confirm the data after performing the drive test.
Turn the power switch off.
OK
NG
Connect the intelligent tester to the DLC3.
Turn the power switch on (READY).
Enter the following menus: Powertrain / Hybrid Control / Data List / Vehicle Spd.
Read the value displayed on the intelligent tester.
| Tester Display | Condition | Specified Condition |
|---|---|---|
| Vehicle Spd | Vehicle stopped | 0 km/h (0 mph) |
| Vehicle being driven at a constant speed (16 to 64 km/h (10 to 40 mph)) | No large fluctuations in displayed speed |
Perform this road test only in an appropriate safe location, in accordance with all local laws.
Data can be captured relatively easily by using the snapshot function in the Data List. Confirm the data after performing the drive test.
Turn the power switch off.
OK
NG
Connect the intelligent tester to the DLC3.
Turn the power switch on (READY).
Enter the following menus: Chassis / ABS/VSC/TRC / Data List / Deceleration Sensor and Deceleration Sensor2.
Read the value displayed on the intelligent tester.
| Tester Display | Condition | Specified Condition |
|---|---|---|
| Deceleration Sensor
Deceleration Sensor2 |
During deceleration | Value changes with vehicle speed |
| During acceleration | Value changes with vehicle speed |
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Data can be captured relatively easily by using the snapshot function in the Data List. Confirm the data after performing the drive test.
Turn the power switch off.
OK
NG
Connect the intelligent tester to the DLC3.
Turn the power switch on (READY).
Enter the following menus: Chassis / ABS/VSC/TRC / Data List / Steering Angle Sensor.
Read the value displayed on the intelligent tester.
| Tester Display | Measurement Item / Range | Normal Condition |
|---|---|---|
| Steering Angle Sensor | Steering angle sensor
Min.: -3276.8 degrees, Max.: 3276.7 degrees |
Turning left: Increases
Turning right: Decreases |
| Tester Display | Condition | Specified Condition |
|---|---|---|
| Steering Angle Sensor | Steering wheel turned left | Value increases with steering wheel operation |
| Steering wheel turned right | Value decreases with steering wheel operation |
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Data can be captured relatively easily by using the snapshot function in the Data List. Confirm the data after performing the drive test.
Turn the power switch off.
OK
NG
Check if the customer operated the vehicle in a way that would cause the drive start control to operate.
Drive Start Control Activation Conditions
Condition 1 (Reverse control)
The shift lever is in R.
The accelerator pedal is depressed.
Driving torque is restricted.
The shift lever is moved to any position other than R.
The accelerator pedal is released.
Condition 2 (Shift control A)
The shift lever is moved from P to any forward position (D or B) or R.
The accelerator pedal is open by approximately 1/5 or more.
Driving torque is restricted.
The shift lever is in P or N.
The accelerator pedal is released.
Condition 3 (Shift control B)
The shift lever is moved from R to any forward position (D or B), any forward position (D or B) to R, or N to R.
The accelerator pedal is open by approximately 1/5 or more.
Driving torque is restricted.
The shift lever is in P or N.
The accelerator pedal is released.
During reverse control or shift control, driving torque is adjusted based on the road gradient and steering angle.
| Result | Proceed to |
|---|---|
| Not performed | A |
| Performed | B |
If the customer operated the vehicle in a way which caused the drive start control to operate, explain the operation of the system to the customer and that the operation is not a malfunction.
A
B
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Enter the following menus: System Select / Utility / All Codes.
Check for DTCs.
| Result | Proceed to |
|---|---|
| No DTCs are output. | A |
| DTCs are output | B |
Turn the power switch off.
A
B
Inspect the shift lever position sensor (See page Drivetrain>P510 (HYBRID TRANSMISSION / TRANSAXLE)>SHIFT LEVER POSITION SENSOR>INSPECTION).
A
B
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>ACCELERATOR PEDAL SENSOR>ON-VEHICLE INSPECTION
OK
NG