Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › from 2014.12
RM2170E _51 Engine / Hybrid System _057004 HYBRID / BATTERY CONTROL _0277924 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0BEA-290  Drive Motor "A" Phase V Current Sensor Circuit Range / Performance  P0BEE-298  Drive Motor "A" Phase V Current Sensor Circuit Range / Performance  P1C3C-294  Drive Motor "A" Phase V Current Sensor Correlation  P1C3D-302  Drive Motor "A" Phase W Current Sensor Correlation  P1C4A-288  Drive Motor "A" Phase V Current Sensor Sub Circuit Range / Performance  P1C4F-296  Drive Motor "A" Phase W Current Sensor Sub Circuit Range / Performance  P1C6D-501  Drive Motor "A" Phase V Current Sensor Offset Range / Performance  P1C6E-502  Drive Motor "A" Phase W Current Sensor Offset Range / Performance  


DESCRIPTION

The MG ECU located in the inverter with converter assembly monitors the motor inverter current sensors. P0A60 and P0A63 indicate malfunctions in current sensors, and they do not indicate malfunctions in the high-voltage system.

HINT:

The term "drive motor A" indicates MG2.


DTC No. INF Code DTC Detection Condition Trouble Area
P0BEA 290 Malfunction in motor inverter current sensor (phase V main sensor)
(1 trip detection logic)
Inverter with converter assembly
P0BEE 298 Malfunction in motor inverter current sensor (phase W main sensor)
(1 trip detection logic)
P1C3C 294 Malfunction in motor inverter current sensor (performance problem or open phase V)
(1 trip detection logic)
P1C3D 302 Malfunction in motor inverter current sensor (performance problem or open phase W)
(1 trip detection logic)
P1C4A 288 Malfunction in motor inverter current sensor (phase V sub sensor)
(1 trip detection logic)
P1C4F 296 Malfunction in motor inverter current sensor (phase W sub sensor)
(1 trip detection logic)
P1C6D 501 Malfunction in motor inverter current sensor (phase V main and sub sensors offset)
(1 trip detection logic)
P1C6E 502 Malfunction in motor inverter current sensor (phase W main and sub sensors offset)
(1 trip detection logic)

CAUTION / NOTICE / HINT

CAUTION:
·

Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·

After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION).

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Turn the power switch on (IG) and wait for 5 seconds or more.

2.

Turn the power switch on (READY) with the shift lever in P and wait for 5 seconds or more.

3.

Move the shift lever to N and wait for 5 seconds or more.

4.

Depress the accelerator pedal of the vehicle with the engine stopped and the shift lever in P to start the engine.

5.

Drive the vehicle forward with the shift lever in D for 5 m or more.

6.

Drive the vehicle backward with the shift lever in R for 5 m or more.



PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / DTC.


d.

Check if DTCs are output.

Result:
Result Proceed to
P0BEA-290, P0BEE-298, P1C3C-294, P1C3D-302, P1C4A-288, P1C4F-296, P1C6D-501 or P1C6E-502 only is output, or DTCs other than the ones in the table below are also output. A
P0A78-202 is output. B



e.

Turn the power switch off.



A

2.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

B

2.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

OK

REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS

NG

CONNECT SECURELY