Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › from 2014.12
RM2170E _51 Engine / Hybrid System _057004 HYBRID / BATTERY CONTROL _0277924 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  U0110-194  Lost Communication with Drive Motor Control Module "A"  U0110-197  Lost Communication with Drive Motor Control Module "A"  U0110-199  Lost Communication with Drive Motor Control Module "A"  U0110-230  Lost Communication with Drive Motor Control Module "A"  


DESCRIPTION

Refer to the description for DTC U0110-159 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>U0110-159).

DTC No. INF Code DTC Detection Condition Trouble Area
U0110 194 Error in signal transmission to the inverter with converter assembly (MG ECU) via serial communication (no reception)
(1 trip detection logic)
·

Wire harness or connector

·

Inverter with converter assembly

·

Hybrid vehicle transaxle assembly

·

Motor cable

·

Hybrid vehicle control ECU


197 Error in signal transmission to the inverter with converter assembly (MG ECU) via serial communication (out of communication standard)
(1 trip detection logic)
·

Wire harness or connector

·

Inverter with converter assembly

·

Hybrid vehicle transaxle assembly

·

Motor cable

·

Hybrid vehicle control ECU


199 Error in signal transmission to the inverter with converter assembly (MG ECU) via serial communication (out of communication standard)
(1 trip detection logic)
·

Wire harness or connector

·

Inverter with converter assembly

·

Hybrid vehicle transaxle assembly

·

Motor cable

·

Hybrid vehicle control ECU


230 Error in signal transmission to the inverter with converter assembly (MG ECU) via serial communication (abnormal REQ signal)
(1 trip detection logic)
·

Wire harness or connector

·

Inverter with converter assembly

·

Hybrid vehicle transaxle assembly

·

Motor cable

·

Hybrid vehicle control ECU



WIRING DIAGRAM

Refer to the wiring diagram for DTC P0AA6-526 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0AA6-526).

Refer to the wiring diagram for DTC U0110-159 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>U0110-159).

CAUTION / NOTICE / HINT

CAUTION:
·

Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·

After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION).

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:
·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

If the DTC U0110-160 was set due to incomplete engagement of the connectors, and if the system returns to normal when the power switch is on (IG) after clearing the DTCs, DTC P324E-788 will be set. Proceed to troubleshooting without considering DTC P324E-788.



HINT:

After the repair, clear the DTCs and perform the following procedure to check the DTCs are not output.

1.

Turn the power switch on (IG) and wait for 2 minutes or more.



PROCEDURE

1.CLEAR DTC

NEXT

2.CHECK DTC OUTPUT (HYBRID CONTROL)
2.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / DTC.


d.

Check if DTCs are output.

Result:
Result Proceed to
U0110-194, 197, 199 or 230 is output. A
U0110-194, 197, 199 or 230 is not output. B



e.

Turn the power switch off.



A

3.CHECK INVERTER WITH CONVERTER ASSEMBLY (MOTOR CABLE (FOR MG1) CONNECTION CONDITION)

B

3.CHECK INVERTER WITH CONVERTER ASSEMBLY (MOTOR CABLE (FOR MG1) CONNECTION CONDITION)

A

4.CHECK INVERTER WITH CONVERTER ASSEMBLY (MOTOR CABLE (FOR MG2) CONNECTION CONDITION)

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY

4.CHECK INVERTER WITH CONVERTER ASSEMBLY (MOTOR CABLE (FOR MG2) CONNECTION CONDITION)

A

5.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MG1)

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY

5.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MG1)

OK

6.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MG2)

NG

16.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MOTOR CABLE (FOR MG1) CONNECTION CONDITION)
6.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MG2)

OK

7.CHECK HYBRID VEHICLE CONTROL ECU (CHECK WAVEFORM)

NG

18.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MOTOR CABLE (FOR MG2) CONNECTION CONDITION)
7.CHECK HYBRID VEHICLE CONTROL ECU (CHECK WAVEFORM)
a.

Connect an oscilloscope between the hybrid vehicle control ECU terminals specified in the following table.


b.

Turn the power switch on (IG).


c.
A390228E01
1.167,0.333 1.583,0.583 0.417,0.25 1.75,0.333 2.167,0.583 0.417,0.25 1.104,1.677 1.354,1.208 false 1.594,1.688 1.396,1.208 false 2.063,1.625 1.76,1.083 false 2.802,3.5 3.26,3.698 0.458,0.198 10 false GND 2.823,4.063 3.281,4.26 0.458,0.198 10 false GND 0.188,3.125 0.646,3.323 0.458,0.198 10 false CH1 0.906,1.719 1.365,1.917 0.458,0.198 10 false HTM- 0.094,0.104 0.552,0.302 0.458,0.198 10 false *a 1.25,0.375 1.708,0.573 0.458,0.198 10 false A72 1.823,0.375 2.281,0.573 0.458,0.198 10 false G80 2.073,1.688 2.531,1.885 0.458,0.198 10 false E1 1.469,1.729 1.927,1.927 0.458,0.198 10 false HTM+ 0.198,3.854 0.656,4.052 0.458,0.198 10 false CH2

Measure the waveform.

Item Contents
Tester Connection CH1: A72-24 (HTM+) - G80-6 (E1)
CH2: A72-25 (HTM-) - G80-6 (E1)
Equipment Setting 1V/DIV., 200μs/DIV.
Condition Power switch on (IG)

Result:
Result Proceed to
The waveform appears as shown in the illustration. A
The waveform differs from the one shown in the illustration. B


Text in Illustration
*a Component with harness connected
(Hybrid Vehicle Control ECU)

HINT:
·

Inspect with the connector connected.

·

If pulses are generated, the shape of the waveform can be assumed to be normal.

·

The shape of the waveform may vary according to communication conditions.




d.

Turn the power switch off.



A

8.CHECK HYBRID VEHICLE CONTROL ECU (CHECK WAVEFORM)

B

14.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - INVERTER WITH CONVERTER ASSEMBLY)
8.CHECK HYBRID VEHICLE CONTROL ECU (CHECK WAVEFORM)

A

9.CHECK HYBRID VEHICLE CONTROL ECU (CHECK WAVEFORM)

B

10.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - INVERTER WITH CONVERTER ASSEMBLY)
9.CHECK HYBRID VEHICLE CONTROL ECU (CHECK WAVEFORM)

A

REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS

B

12.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - INVERTER WITH CONVERTER ASSEMBLY)
10.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - INVERTER WITH CONVERTER ASSEMBLY)

OK

11.CHECK INVERTER WITH CONVERTER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - INVERTER WITH CONVERTER ASSEMBLY)

OK

13.CHECK INVERTER WITH CONVERTER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - INVERTER WITH CONVERTER ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect connector A72 from the hybrid vehicle control ECU.


c.

Disconnect connector A47 from the inverter with converter assembly.


d.

Connect the cable to the negative (-) auxiliary battery terminal.


e.

Turn the power switch on (IG).


f.
U183214E02
1.417,2.219 1.74,2.542 false 1.375,2.219 0.865,2.542 false 1.823,3.625 1.219,4.333 false 1.823,3.708 2.219,4.302 false 0.104,0.115 0.396,0.354 0.292,0.24 10 false *a 0.104,2.917 0.396,3.156 0.292,0.24 10 false *b 0.51,2.51 1.031,2.667 0.521,0.156 10 false HTM- 1.625,2.563 2.146,2.719 0.521,0.156 10 false HTM+ 1.302,2.771 1.573,2.938 0.271,0.167 10 false A72 0.521,3.688 0.792,3.854 0.271,0.167 10 false A47 0.969,4.333 1.49,4.49 0.521,0.156 10 false HTM+ 2.083,4.344 2.604,4.5 0.521,0.156 10 false HTM-

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A72-24 (HTM+) - Body ground Power switch on (IG) Below 1 V
A72-25 (HTM-) - Body ground Power switch on (IG) Below 1 V


Text in Illustration
*a Rear view of wire harness connector
(to Hybrid Vehicle Control ECU)
*b Front view of wire harness connector
(to Inverter with Converter Assembly)

NOTICE:

Turning the power switch on (IG) with the connector of the hybrid vehicle control ECU and the low voltage connector of the inverter with converter assembly disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



g.

Turn the power switch off.


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Switch Condition Specified Condition
A72-24 (HTM+) - A47-8 (HTM+) Power switch off Below 1 Ω
A72-25 (HTM-) - A47-18 (HTM-) Power switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Switch Condition Specified Condition
A72-24 (HTM+) or A47-8 (HTM+) - Body ground and other terminals Power switch off 10 kΩ or higher
A72-25 (HTM-) or A47-18 (HTM-) - Body ground and other terminals Power switch off 10 kΩ or higher



i.

Disconnect the cable from the negative (-) auxiliary battery terminal.


j.

Connect the inverter with converter assembly connector.


k.

Connect the hybrid vehicle control ECU connector.



OK

15.CHECK INVERTER WITH CONVERTER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.CHECK INVERTER WITH CONVERTER ASSEMBLY
a.

Disconnect connector A72 from the hybrid vehicle control ECU.


b.
U183181E02
1.354,2.51 1.146,2.958 false 1.406,2.51 1.615,2.958 false 0.688,2.302 0.958,2.469 0.271,0.167 10 false A72 0.896,2.969 1.281,3.135 0.385,0.167 10 false HTM- 1.479,2.969 1.917,3.135 0.438,0.167 10 false HTM+ 0.229,0.198 0.427,0.365 0.198,0.167 10 false *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A72-24 (HTM+) - A72-25 (HTM-) Power switch off 80 to 170 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Hybrid Vehicle Control ECU)


c.

Connect the hybrid vehicle control ECU connector.



OK

NG

REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS

16.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MOTOR CABLE (FOR MG1) CONNECTION CONDITION)

A

17.CHECK MOTOR CABLE (FOR MG1)

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY

18.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MOTOR CABLE (FOR MG2) CONNECTION CONDITION)

A

19.CHECK MOTOR CABLE (FOR MG2)

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY