Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID BATTERY SYSTEM › 2011.12–2014.12
RM2170E _51 Engine / Hybrid System _057004 HYBRID / BATTERY CONTROL _0277925 HYBRID BATTERY SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID BATTERY SYSTEM  P0A9D-123  Hybrid Battery Temperature Sensor "A" Circuit Low  P0A9E-123  Hybrid Battery Temperature Sensor "A" Circuit High  P0AC7-123  Hybrid Battery Temperature Sensor "B" Circuit Low  P0AC8-123  Hybrid Battery Temperature Sensor "B" Circuit High  P0ACC-123  Hybrid Battery Temperature Sensor "C" Circuit Low  P0ACD-123  Hybrid Battery Temperature Sensor "C" Circuit High  


DESCRIPTION

Refer to the description for DTC P0A9C-123 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>P0A9C-123).


DTC No. INF Code DTC Detection Condition Trouble Area
P0A9D
P0A9E
P0AC7
P0AC8
P0ACC
P0ACD
123 When the temperature of the battery temperature sensor is less than the standard value (open) or higher than the standard value (shorted) (1 trip detection).
·

Hybrid battery thermistor

·

Battery smart unit

·

Wire harness or connector



HINT:

After confirming that a DTC is output, use the intelligent tester to check "Temp of BATT TB 1 to 3" in the hybrid vehicle control system ECU data list.


Temperature Displayed Malfunction
Below -45°C (-49°F) Open or +B short circuit
95°C (203°F) or more GND short circuit

WIRING DIAGRAM

Refer to the wiring diagram for DTC P0A9C-123 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>P0A9C-123).

CAUTION / NOTICE / HINT

CAUTION:
·

Before inspecting the high-voltage system, take safety precautions to prevent electrical shocks, such as wearing insulated gloves and removing the service plug grip. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·

After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>PRECAUTION).

HINT:

At least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.


·

When disposing of an HV battery, make sure to return it through an authorized collection agent who is capable of handling it safely. If the HV battery is returned via the manufacturer specified route, it will be returned properly and in a safe manner by an authorized collection agent.



NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)

A

2.READ VALUE USING INTELLIGENT TESTER

B

2.READ VALUE USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Data List / Temp of Batt TB 1 to 3.

HINT:

Compare the temperature of the 3 battery temperature sensors to determine the sensor with the malfunction (Temp of Batt TB1 to TB3).



d.

Turn the power switch off.



NEXT

3.CHECK CONNECTOR CONNECTION CONDITION
3.CHECK CONNECTOR CONNECTION CONDITION
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 hybrid battery shield sub-assembly (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY SMART UNIT>REMOVAL).


c.
A389836E01
1.323,1.854 1.635,2.073 0.313,0.219 1.417,1.885 1.729,2.083 0.313,0.198 10 false d1

Check the connections of the d1 connector of the battery smart unit.

OK:

The connectors are connected securely and there are no contact problems.



d.

Install the No. 1 hybrid battery shield sub-assembly.



OK

4.CHECK HYBRID BATTERY THERMISTOR (BATTERY TEMPERATURE SENSOR)

NG

CONNECT SECURELY

4.CHECK HYBRID BATTERY THERMISTOR (BATTERY TEMPERATURE SENSOR)

OK

NG

5.CHECK HARNESS AND CONNECTOR (BATTERY TEMPERATURE SENSOR)
5.CHECK HARNESS AND CONNECTOR (BATTERY TEMPERATURE SENSOR)

OK

NG

REPAIR HARNESS OR CONNECTOR