Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID BATTERY SYSTEM › from 2014.12
RM2170E _51 Engine / Hybrid System _057004 HYBRID / BATTERY CONTROL _0277925 HYBRID BATTERY SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID BATTERY SYSTEM  U029A-123  Lost Communication with Hybrid Battery Pack Sensor Module  


DESCRIPTION

The battery smart unit detects the HV battery conditions (voltage, current, and temperature) and battery cooling fan voltage, and sends the detected signals to the hybrid vehicle control ECU via serial communication.

DTC No. INF Code DTC Detection Condition Trouble Area
U029A 123 Problem in serial communication between the battery smart unit and hybrid vehicle control ECU (1 trip detection)
·

Wire harness or connector

·

Hybrid vehicle control ECU

·

Battery smart unit



WIRING DIAGRAM

Refer to the wiring diagram for DTC P0AFC-123 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>P0AFC-123).

CAUTION / NOTICE / HINT

CAUTION:
·

Before inspecting the high-voltage system, take safety precautions to prevent electrical shocks, such as wearing insulated gloves and removing the service plug grip. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·

After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>PRECAUTION).

HINT:

At least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / DTC.


d.

Check for DTCs (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
Only U029A-123 is output. A
DTCs other than U029A-123 are also output. B



e.

Turn the power switch off.


f.

Disconnect the intelligent tester from the DLC3.



A

2.CHECK BATTERY SMART UNIT (IGCT VOLTAGE)

B

2.CHECK BATTERY SMART UNIT (IGCT VOLTAGE)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 hybrid battery exhaust duct (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY SMART UNIT>REMOVAL).


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the power switch on (IG).


e.
U158969E03
1.333,1.229 1.031,0.531 true 1.333,1.292 0.531,2.49 true 0.146,0.125 0.333,0.292 0.188,0.167 10 false *a 0.313,2.521 0.656,2.76 0.344,0.24 10 false GND 0.698,0.406 1.083,0.625 0.385,0.219 10 false IGCT 0.313,1.188 0.823,1.479 0.51,0.292 10 false M39

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
M39-3 (IGCT) - M39-6 (GND) Power switch on (IG) 11 to 14 V


Text in Illustration
*a Component with harness connected
(Battery Smart Unit)

NOTICE:

Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.


HINT:

As there might be an intermittent malfunction in the battery smart unit power source circuit, inspect the following even if the measured voltage is as specified:


·

Installation condition of fuse(s) (before removing fuse(s)) (IGCT circuit)

·

Fuse condition (before and after removing fuse(s)) (IGCT circuit)

·

Connection condition of connectors (IGCT circuit)

·

Wire harness condition (IGCT circuit)

·

Wire harness condition (GND circuit)



f.

Turn the power switch off.


g.

Disconnect the cable from the negative (-) auxiliary battery terminal.


h.

Install the No. 1 hybrid battery exhaust duct.



OK

3.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - BATTERY SMART UNIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY SMART UNIT POWER SOURCE CIRCUIT)

3.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - BATTERY SMART UNIT)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect connector G80 from the hybrid vehicle control ECU (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID VEHICLE CONTROL ECU>REMOVAL).


c.

Remove the No. 1 hybrid battery exhaust duct (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY SMART UNIT>REMOVAL).


d.

Disconnect connector M39 from the battery smart unit.


e.
A380671E02
1,2.083 1.417,2.333 0.417,0.25 1.417,2.75 1.875,2.344 false 2.583,2.75 1.938,2.344 false 0.406,0.385 0.719,0.583 0.313,0.198 10 false *a 1.073,2.125 1.385,2.323 0.313,0.198 10 false G80 1.031,2.677 1.49,2.938 0.458,0.26 10 false BTH- 2.625,2.698 3.083,2.958 0.458,0.26 10 false BTH+

A380672E01
0.833,2.5 1.25,2.75 0.417,0.25 1.875,2.552 2.5,2.417 false 1.865,2.698 2.5,2.917 false 0.792,0.479 1.104,0.677 0.313,0.198 10 false *b 0.896,2.531 1.208,2.729 0.313,0.198 10 false M39 2.552,2.323 3.021,2.552 0.469,0.229 10 false BTH+ 2.542,2.844 3.01,3.073 0.469,0.229 10 false BTH-

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G80-32 (BTH+) - M39-1 (BTH+) Power switch off Below 1 Ω
G80-33 (BTH-) - M39-4 (BTH-) Power switch off Below 1 Ω
G80-32 (BTH+) - Other terminals and body ground Power switch off 10 kΩ or higher
G80-33 (BTH-) - Other terminals and body ground Power switch off 10 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to Hybrid Vehicle Control ECU)
*b Rear view of wire harness connector
(to Battery Smart Unit)


f.

Connect the cable to the negative (-) auxiliary battery terminal.


g.

Turn the power switch on (IG).


h.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G80-32 (BTH+) - body ground Power switch on (IG) Below 1 V
G80-33 (BTH-) - body ground Power switch on (IG) Below 1 V


NOTICE:

Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.



i.

Turn the power switch off.


j.

Disconnect the cable from the negative (-) auxiliary battery terminal.


k.

Connect the battery smart unit connector.


l.

Install the No. 1 hybrid battery exhaust duct.


m.

Connect the hybrid vehicle control ECU connector.



OK

4.CHECK HYBRID VEHICLE CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (HYBRID VEHICLE CONTROL ECU - BATTERY SMART UNIT)

4.CHECK HYBRID VEHICLE CONTROL ECU
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 hybrid battery exhaust duct (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY SMART UNIT>REMOVAL).


c.

Disconnect connector M39 from the battery smart unit.


d.

Connect the cable to the negative (-) auxiliary battery terminal.


e.

Turn the power switch on (IG).


f.
U158967E02
1.906,2.375 2.406,2.031 false 2.51,2.927 1.917,2.51 false 1.104,2.875 1.604,2.531 false 2.469,1.927 2.875,2.177 0.406,0.25 10 false BTH+ 2.542,2.896 2.969,3.146 0.427,0.25 10 false BTH- 0.792,2.823 1.125,3.073 0.333,0.25 10 false GND 0.75,0.094 0.958,0.333 0.208,0.24 10 false *a 0.979,2.073 1.313,2.219 0.333,0.146 10 false M39

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
M39-1 (BTH+) - M39-6 (GND) Power switch on (IG) 2.3 to 2.7 V
M39-4 (BTH-) - M39-6 (GND) Power switch on (IG) 2.3 to 2.7 V


Text in Illustration
*a Rear view of wire harness connector
(to Battery Smart Unit)


NOTICE:

Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.


g.

Turn the power switch off.


h.

Disconnect the cable from the negative (-) auxiliary battery terminal.


i.
U158968E02
1.927,2.375 2.417,2.042 false 2.542,2.906 1.927,2.521 false 2.479,1.917 2.896,2.167 0.417,0.25 10 false BTH+ 2.573,2.823 3.01,3.073 0.438,0.25 10 false BTH- 0.75,0.219 0.958,0.458 0.208,0.24 10 false *a 0.885,2.313 1.188,2.458 0.302,0.146 10 false M39

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
M39-1 (BTH+) - M39-4 (BTH-) Power switch off 4.4 to 5.4 kΩ


Text in Illustration
*a Rear view of wire harness connector
(to Battery Smart Unit)

HINT:

Resistance becomes 2.0 kΩ or less when there is a short circuit in the hybrid vehicle control ECU.



j.

Connect the battery smart unit connector.


k.

Install the No. 1 hybrid battery exhaust duct.



OK

NG