Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID BATTERY SYSTEM › 2011.12–2014.12
RM2170E _51 Engine / Hybrid System _057004 HYBRID / BATTERY CONTROL _0277925 HYBRID BATTERY SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID BATTERY SYSTEM  P0A82-123  Hybrid Battery Pack Cooling Fan 1 Performance / Stuck OFF  


DESCRIPTION

Refer to the circuit description for DTC P0A84-123 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>P0A84-123).


DTC No. INF Code DTC Detection Condition Trouble Area
P0A82 123 The speed of the battery cooling blower assembly is not within the specified range (1 trip detection)
·

Battery cooling blower assembly

·

Battery smart unit

·

Power management control ECU

·

Front floor cover LH

·

Wire harness or connector



WIRING DIAGRAM

Refer to the wiring diagram for DTC P0A84-123 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>P0A84-123).

CAUTION / NOTICE / HINT

CAUTION:
·

Before inspecting the high-voltage system, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·

After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>PRECAUTION).

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


PROCEDURE

2.CHECK DUCT AND BLOWER
a.
A266553E01
2.102,1.812 2.300,1.986 0.199,0.175 10 *1 2.086,1.903 1.839,1.903 1.839,1.903 1.664,1.347 false

Check that the front floor cover LH and battery cooling blower are not disconnected, damaged, or clogged with foreign objects, and that the acoustical materials have not peeled.

Text in Illustration
*1 Front Floor Cover LH

OK:

The duct and blower are not disconnected, damaged, or clogged with foreign objects and the acoustical materials have not peeled.




OK

3.CHECK HARNESS AND CONNECTOR (BATTERY COOLING BLOWER - BATTERY SMART UNIT)

NG

CORRECT THE PROBLEM

3.CHECK HARNESS AND CONNECTOR (BATTERY COOLING BLOWER - BATTERY SMART UNIT)

OK

4.CHECK HARNESS AND CONNECTOR (BATTERY COOLING BLOWER - POWER MANAGEMENT CONTROL ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (BATTERY COOLING BLOWER - POWER MANAGEMENT CONTROL ECU)

OK

5.CHECK POWER MANAGEMENT CONTROL ECU (GROUND SHORT CHECK)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK POWER MANAGEMENT CONTROL ECU (GROUND SHORT CHECK)
a.

Remove the power management control ECU (See page Power Source / Network>POWER DISTRIBUTION>POWER MANAGEMENT CONTROL ECU>REMOVAL).


b.
U183232E02
2.573,1.042 2.74,0.333 2.74,0.333 2.781,0.333 false 1.885,1.042 1.771,0.323 1.771,0.323 1.708,0.323 false 0.979,1.25 0.979,1.74 false 1.417,0.229 1.74,0.375 0.323,0.146 10 false E01 2.823,0.25 3.146,0.396 0.323,0.146 10 false E02 0.865,1.74 1.115,1.938 0.25,0.198 10 false SI0 0.219,0.115 0.573,0.313 0.354,0.198 10 false *a 0.542,1.5 0.833,1.698 0.292,0.198 10 false A38 1.927,1.51 2.219,1.708 0.292,0.198 10 false G57 2.51,1.5 2.802,1.698 0.292,0.198 10 false G58

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Specified Condition
A38-29 (SI0) - G57-5 (E01) 10 kΩ or higher
A38-29 (SI0) - G58-5 (E02) 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Power Management Control ECU)


c.

Install the power management control ECU.



OK

6.READ VALUE USING INTELLIGENT TESTER (COOLING FAN FREQUENCY)

NG

6.READ VALUE USING INTELLIGENT TESTER (COOLING FAN FREQUENCY)

A

7.CHECK BATTERY SMART UNIT

B

8.CHECK BATTERY SMART UNIT (FREQUENCY)
8.CHECK BATTERY SMART UNIT (FREQUENCY)
a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the rear seat cushion leg sub-assembly (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY SMART UNIT>REMOVAL).


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Connect the intelligent tester. to the DLC3.


e.

Turn the power switch on (IG).

NOTICE:
·

After removing the service plug grip, do not turn the power switch on (READY) unless instructed by the repair manual because this may cause a malfunction.

·

If the power switch is turned on (IG) with the service plug grip removed, DTC P0A0D-350 for the interlock switch system will be stored. If this DTC is output, clear the DTC using the intelligent tester. (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>DTC CHECK / CLEAR).




f.

Enter the following menus: Powertrain / Hybrid Control / Active Test / Driving the Battery Cooling Fan.

NOTICE:

If the Active Test cannot be performed, skip it and proceed to the next step to check Frequency. In accordance with fail-safe system operation, the power management control ECU sends a command to operate the battery cooling fan.



g.

Enter the following menus: All Data / Cooling Fan Frequency 1.


h.

Select each air volume mode (1 to 6) in the "Driving the Battery Cooling Fan" Active Test to operate the battery cooling blower assembly.


i.
U159014E03
0.896,0.833 0.563,0.615 false 0.615,1.188 0.906,1.063 false 0.146,1.667 0.5,1.917 0.354,0.25 10 false *a 0.26,0.5 0.75,0.75 0.49,0.25 10 false FP0 0.198,1.156 0.646,1.406 0.448,0.25 10 false GND0 2.25,0.344 2.729,0.688 0.479,0.344 10 false M41 0.198,0.167 0.552,0.417 0.354,0.25 10 false *b

While the cooling fan is operating, compare the value in the data list (Cooling Fan Frequency 1) with the Frequency value that was actually measured at the battery cooling blower assembly connector.

Standard:
Tester Connection Condition Specified Condition
M41-2 (FP0) - M41-4 (GND0) Battery cooling blower is operating Difference between the value in the Data List (Cooling Fan Frequency 1) and the actual measurement value is 10 % or less.


Text in Illustration
*a Component with harness connected
(Battery Cooling Blower Assembly)
*b Rear view of wire harness connector
(to Battery Cooling Blower Assembly)


NOTICE:

Turning the power switch on (IG) with the service grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.


HINT:

Compare the values in each air volume mode (1 to 6). If the active test cannot be performed, compare the values only in the current air volume mode.


j.

Turn the power switch off.


k.

Disconnect the cable from the negative (-) auxiliary battery terminal.


l.

Install the rear seat cushion leg sub-assembly.



OK

REPLACE BATTERY COOLING BLOWER ASSEMBLY

NG