Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › ELECTRIC VEHICLE CONVERTER
RM2170E _51 Engine / Hybrid System _057004 HYBRID / BATTERY CONTROL _0277940 ELECTRIC VEHICLE CONVERTER A

HYBRID / BATTERY CONTROL  ELECTRIC VEHICLE CONVERTER  REASSEMBLY  


CAUTION / NOTICE / HINT

NOTICE:

Do not cross-thread the bolts when installing them.


HINT:

Prepare 2 tubes of thermal grease X-23-7884-4 when replacing the hybrid vehicle converter kit.

·

For Europe : 08887-83080

·

For except Europe : 08887-02809



PROCEDURE

Hide 1.REMOVE THERMAL GREASE

a.
A360150E03
0.792,2.385 0.896,2.594 0.896,2.594 1,2.594 false 1.479,2.844 1.448,3.01 1.448,3.01 1.323,3.01 false 0.583,2.219 0.49,2.427 0.49,2.427 0.375,2.427 false 1.104,2.948 1.375,3.125 0.271,0.177 10 false *3 0.177,2.323 0.448,2.5 0.271,0.177 10 false *2 1.031,2.51 1.219,2.688 0.188,0.177 10 false *1

Working with another person, install the 4 bolts and 4 nuts to the power module intelligent transistor kit.

Text in Illustration
*1 Bolt
*2 Nut
*3 Antistatic Mat


b.

Place the power module intelligent transistor kit on an antistatic mat.


c.

Using a scraper with its tip wrapped with protective tape, remove any remaining thermal grease from the power module intelligent transistor kit.

NOTICE:
·

Do not touch the circuit board.

·

Do not apply excessive force to the center of the power module intelligent transistor kit.

·

Keep the parts free from foreign matter.

·

Keep thermal grease away from other parts.

·

Do not spray non-residue solvent directly onto the parts when cleaning.

·

Clean parts with a piece of cloth saturated with non-residue solvent.

·

Do not use compressed air when cleaning to prevent dust from flying.




d.

Using a piece of cloth, remove the thermal grease.


e.

Working with another person, remove the 4 bolts and 4 nuts from the power module intelligent transistor kit.


Hide 2.REMOVE SEAL PACKING (FROM INVERTER CASE WITH CONDENSER CONTACT SURFACE)

NOTICE:
·

Only remove seal packing which is uneven, has peeled off or seeped out from between the contact surfaces.

·

Do not drop any removed seal packing into the inverter case with condenser.

·

Do not bend the bus-bars.



a.

Set the inverter case with condenser on its side as shown in the illustration.

NOTICE:

To prevent the inverter case with condenser from falling over, hold it by hand or place an object behind it.



b.

Using a finger or a scraper with its tip wrapped with protective tape, remove any remaining seal packing which is uneven, has peeled off or seeped out from around the contact surface shown in the illustration and inside the bolt holes.

A360151E04
5.104,0.344 5.281,0.188 5.281,0.188 5.458,0.188 false 5.167,0.635 5.49,0.438 5.49,0.438 5.719,0.438 false 5.271,0.823 5.094,0.948 5.094,0.948 4.948,0.948 false 5.469,2.323 5.604,2.01 5.604,2.01 5.76,2.01 false 1.063,0.531 0.698,0.104 0.698,0.104 0.458,0.104 false 2.5,1.969 2.698,2.302 2.698,2.302 2.865,2.302 false 0.281,0.042 0.573,0.24 0.292,0.198 10 false *1 2.896,2.219 3.188,2.417 0.292,0.198 10 false *1 5.51,0.104 5.802,0.302 0.292,0.198 10 false *1 5.75,0.365 6.042,0.563 0.292,0.198 10 false *1 4.76,0.865 5.052,1.063 0.292,0.198 10 false *2 5.802,1.938 6.094,2.135 0.292,0.198 10 false *2 4.375,0.125 4.667,0.323 0.292,0.198 10 false *a

Text in Illustration
*1 Seeped Out or Uneven Seal Packing *2 Light Coat of Seal Packing Remaining on Contact Surface
*a Minimum Requirement for Removal of Seal Packing - -


Hide 3.REMOVE ADHESIVE (FROM NO. 1 AND NO. 2 INVERTER DRAIN PLUGS SEALING SURFACE)

a.
A360152E02
3.101,1.632 3.319,1.875 0.218,0.244 10 *1 0.409,1.728 0.735,1.953 0.326,0.225 9 *1 2.66,1.585 2.864,1.723 false 2.864,1.723 3.044,1.723 false 1.085,1.452 0.809,1.797 false 0.809,1.797 0.618,1.797 false

Remove the protective tape from the installation holes of the No. 1 and No. 2 inverter drain plugs.

Text in Illustration
*1 Protective Tape


b.
A360153E01
0.428,0.135 0.700,0.316 0.272,0.181 10 *1 2.901,0.072 3.173,0.253 0.272,0.181 10 *1 2.563,0.297 2.745,0.164 2.745,0.164 2.864,0.164 false 0.942,0.616 0.755,0.223 0.755,0.223 0.635,0.223 false

Apply protective tape to the installation holes of the No. 1 and No. 2 inverter drain plugs from the inside of the inverter case with condenser.

Text in Illustration
*1 Protective Tape

NOTICE:

Do not bend the bus-bars when applying protective tape.



c.

Using a scraper with its tip wrapped with protective tape, remove any remaining adhesive from the sealing surfaces of the No. 1 and No. 2 inverter drain plugs.

A360154E01
0.466,0.222 0.739,0.404 0.272,0.181 10 *1 6.623,0.179 6.895,0.360 0.272,0.181 10 *1 5.907,1.097 6.321,0.266 6.321,0.266 6.593,0.266 false 1.173,1.189 0.864,0.289 0.864,0.289 0.666,0.289 false

Text in Illustration
*1 Sealing Surface - -

NOTICE:

Do not damage the sealing surfaces.



d.

Remove any adhesive shavings using tape or equivalent.


e.

Remove the protective tape from the inside of the inverter case with condenser.


f.
A360152E02
3.101,1.632 3.319,1.875 0.218,0.244 10 *1 0.409,1.728 0.735,1.953 0.326,0.225 9 *1 2.66,1.585 2.864,1.723 false 2.864,1.723 3.044,1.723 false 1.085,1.452 0.809,1.797 false 0.809,1.797 0.618,1.797 false

Apply protective tape to the installation holes of the No. 1 and No. 2 inverter drain plugs as shown in the illustration.

Text in Illustration
*1 Protective Tape


Hide 4.REMOVE RESIDUE (FROM INVERTER SIGNAL CONNECTOR COVER SEALING SURFACE)

a.
A360155E01
0.488,0.063 0.760,0.244 0.272,0.181 10 *1 1.335,0.679 0.856,0.122 0.856,0.122 0.69,0.122 false

Apply protective tape to the area shown in the illustration to prevent removed residue from entering the inverter case with condenser.

Text in Illustration
*1 Protective Tape


b.
A360156

Using 600-grit sandpaper, remove the residue from each grommet sealing surface until it feels smooth.

NOTICE:
·

Use 600-grit or higher sandpaper.

·

Do not allow removed residue to enter the inverter case with condenser or hybrid vehicle converter kit.

·

Do not touch or allow grease or oil to contact the sealing surfaces of the inverter case with condenser.




c.

Remove any residue particles using tape or equivalent.


d.

Remove the protective tape.


e.

Thoroughly wash your hands after performing this step.

HINT:

It is not necessary to perform this step if performing the "Remove Residue (from Grommet Sealing Surface)" procedure next.



Hide 5.REMOVE RESIDUE (FROM GROMMET SEALING SURFACE)

HINT:

Perform the following procedure only when there is residue on the grommet sealing surfaces:


a.
A360157E01
0.05,1.135 0.484,1.478 0.434,0.343 10 *1 0.411,0.148 0.845,0.492 0.434,0.343 10 *2 0.635,0.217 0.824,0.217 0.824,0.217 0.874,0.36 false 2.826,3.622 3.260,3.965 0.434,0.343 10 *2 2.792,3.695 2.18,3.695 2.18,3.695 2.015,3.988 false

Apply protective tape to the areas shown in the illustration to prevent removed residue from entering the inverter case with condenser.

Text in Illustration
*1 Inverter Case with Condenser
*2 Protective Tape


b.

Using 600-grit sandpaper, remove the residue from each grommet sealing surface until it feels smooth.

A360158E01
1.566,0.606 1.031,0.246 false 1.031,0.246 0.483,0.246 false 1.387,0.975 0.912,0.727 false 0.912,0.727 0.48,0.727 false 0.298,0.624 0.688,0.902 0.390,0.279 10 *a 0.294,0.155 0.609,0.360 0.316,0.205 10 *a

Text in Illustration
*a Residue - -

NOTICE:
·

Use 600-grit or higher sandpaper.

·

Do not allow removed residue to enter the inverter case with condenser




c.

Remove any adhesive shavings particles using tape or equivalent.


d.

Remove the protective tape.


e.

Thoroughly wash your hands after performing this step.


Hide 6.CLEAN INVERTER SIGNAL CONNECTOR COVER

a.
A314639E01
2.201,0.008 2.387,0.158 0.186,0.150 10 *1

Remove the gasket from the inverter signal connector cover. Wash the gasket and inverter signal connector cover with water and dry them completely.

NOTICE:

Do not damage the gasket.


Text in Illustration
*1 Gasket


b.

Thoroughly wash your hands after performing this step.


Hide 7.INSTALL POWER MODULE INTELLIGENT TRANSISTOR KIT

NOTICE:
·

Do not touch the circuit board.

·

Do not allow any moisture to come into contact with the circuit board.



a.
A360159E02
0.26,0.167 0.469,0.167 0.469,0.167 0.792,0.385 false 3.083,1.917 2.969,1.917 2.969,1.917 2.75,1.323 false 2.917,0.146 2.646,0.146 2.646,0.146 2.01,0.604 false 1.417,2.052 1.229,2.052 1.229,2.052 1.271,1.094 false 0.083,0.042 0.281,0.24 0.198,0.198 10 false *1 3.135,1.833 3.333,2.031 0.198,0.198 10 false *1 1.5,1.958 1.698,2.115 0.198,0.156 10 false *a 2.979,0.042 3.177,0.198 0.198,0.156 10 false *a

Place the hybrid vehicle converter kit so that the guide pins are positioned as shown in the illustration and clean the thermal grease contacting area of the hybrid vehicle converter kit.

Text in Illustration
*1 Guide Pins
*a Thermal Grease Contacting Area

CAUTION:

Do not apply non-residue solvent directly to the hybrid vehicle converter kit when cleaning.


HINT:

Clean the hybrid vehicle converter kit contact surfaces with a piece of cloth saturated with non-residue solvent.



b.
A360160E01
1.51,1.973 1.659,2.122 0.149,0.149 10 *1 1.696,2.044 2.157,2.044 2.157,2.044 2.252,1.85 false

Apply protective tape to the wire harness to keep it free from grease.

Text in Illustration
*1 Protective Tape


c.
A360161E01
3.04,0.012 3.203,0.174 0.163,0.163 10 *1 2.996,0.092 2.731,0.092 2.731,0.092 2.574,0.273 false 3.085,1.62 3.248,1.783 0.163,0.163 10 *1 3.023,1.718 2.849,1.718 2.849,1.718 2.745,1.56 false

Apply protective tape to the hybrid vehicle converter kit as shown in the illustration to prevent grease from entering it.

Text in Illustration
*1 Protective Tape


d.
A362219E01
0.287,1.668 0.436,1.817 0.149,0.149 10 *1 0.473,1.738 0.933,1.738 0.933,1.738 1.029,1.544 false

Bend the masking seal as shown in the illustration.

Text in Illustration
*1 Do not remove

NOTICE:

Do not remove the release paper from the bent portion of the masking seal. If the adhesive surface of the masking seal contacts a bus-bar, the bus-bar may be bent when removing the masking seal.



e.
A362220

Remove the release paper from the masking seal.

NOTICE:

Do not remove the release paper from the bent portion of the masking seal.



f.

Align the guide holes of the masking seal with the guide pins as shown in the illustration, and attach the masking seal to the hybrid vehicle converter kit.

A362221E02
1.26,1.01 1.635,0.156 1.635,0.156 1.833,0.156 false 6.271,0.771 6.552,0.188 6.552,0.188 6.76,0.188 false 3.885,0.427 4.021,0.083 4.021,0.083 4.177,0.083 false 1.156,1.625 1.344,2.521 1.344,2.521 1.49,2.521 false 6.031,1.531 6.292,2.427 6.292,2.427 6.5,2.427 false 1.875,0.083 2.146,0.26 0.271,0.177 10 false *3 4.24,0.031 4.51,0.208 0.271,0.177 10 false *1 1.51,2.427 1.698,2.604 0.188,0.177 10 false *2 6.823,0.115 7.031,0.292 0.208,0.177 10 false *3 6.531,2.354 6.719,2.531 0.188,0.177 10 false *2

Text in Illustration
*1 Masking Seal *2 Guide Pin
*3 Guide Hole - -


g.

Check that the masking seal is attached correctly, then firmly press on it with your fingers to securely attach it.

A362222

NOTICE:
·

Securely attach the masking seal without leaving any air bubbles.

·

Do not touch the bus-bars when attaching the masking seal.




h.
A293968

Gently squeeze the tube of thermal grease and apply a small amount to a piece of cloth.

HINT:

Some clear liquid may come out first. Squeeze it out completely onto a piece of cloth.



i.

Apply thermal grease to 14 places as shown in the illustration.

A362224E03
2.854,3.792 3.125,3.969 0.271,0.177 10 false *a 2.854,3.26 3.125,3.438 0.271,0.177 10 false *a 2.854,3.438 3.125,3.615 0.271,0.177 10 false *a 2.854,3.625 3.125,3.802 0.271,0.177 10 false *a 2.854,3.979 3.125,4.156 0.271,0.177 10 false *a 5.75,3.219 6.021,3.396 0.271,0.177 10 false *a 5.75,4.104 6.021,4.281 0.271,0.177 10 false *a 5.75,3.677 6.021,3.854 0.271,0.177 10 false *a 5.74,3.438 6.01,3.615 0.271,0.177 10 false *a 5.75,3.885 6.021,4.063 0.271,0.177 10 false *a 5.75,4.542 6.021,4.719 0.271,0.177 10 false *a 5.75,4.323 6.021,4.5 0.271,0.177 10 false *a 2.281,4.052 2.5,4.208 0.219,0.156 10 true *b 2.281,3.521 2.531,3.677 0.25,0.156 10 true *b 2.281,3.698 2.51,3.844 0.229,0.146 10 true *b 2.281,3.865 2.542,4.021 0.26,0.156 10 true *b 2.281,3.344 2.542,3.49 0.26,0.146 10 true *b 5.219,3.333 5.49,3.51 0.271,0.177 10 false *b 5.219,4.208 5.479,4.354 0.26,0.146 10 true *b 5.219,3.771 5.49,3.948 0.271,0.177 10 false *b 5.219,3.563 5.469,3.708 0.25,0.146 10 true *b 5.219,3.979 5.5,4.135 0.281,0.156 10 true *b 5.219,4.646 5.479,4.792 0.26,0.146 10 true *b 5.219,4.427 5.49,4.604 0.271,0.177 10 false *b 3.542,5.313 3.813,5.49 0.271,0.177 10 false *c 2.958,5.688 3.229,5.865 0.271,0.177 10 false *d 5.198,3.125 5.458,3.271 0.26,0.146 10 true *b 5.208,2.896 5.458,3.052 0.25,0.156 10 true *b 5.75,3 6.021,3.177 0.271,0.177 10 false *a 5.75,2.781 6.021,2.958 0.271,0.177 10 false *a

Text in Illustration
*a Reference Line *b Almost equally spaced
*c Approximately 6.0 mm (0.236 in.) *d Approximately 2.0 mm (0.0787 in.)


j.
A362226E02
1.917,0.792 1.781,0.552 1.781,0.552 1.604,0.552 false 1.865,3.688 2.073,4.594 2.073,4.594 2.229,4.594 false 1.396,0.469 1.667,0.646 0.271,0.177 10 false *1 2.281,4.49 2.552,4.667 0.271,0.177 10 false *1 2.313,0.76 2.583,0.938 0.271,0.177 10 false *a

Using SST, carefully apply the thermal grease smoothly and evenly by spreading it as shown in the illustration. (Procedure A)

SST
09891-47010  

Text in Illustration
*1 SST
*a 45°

NOTICE:
·

Before performing work, check that the thermal grease contacting area of SST is not damaged.

·

Apply the thermal grease smoothly and evenly to ensure proper heat transfer.

·

Keep SST at a 45-degree angle and perform work carefully.




k.

Change the orientation of SST as shown in the illustration. (Procedure B)

A362228E02
2.281,0.406 2.167,0.292 2.167,0.292 2.073,0.292 false 5.792,0.375 5.906,0.281 5.906,0.281 6,0.281 false 1.708,2.021 1.906,2.594 1.906,2.594 1.979,2.594 false 5.427,2.031 5.625,2.594 5.625,2.594 5.698,2.594 false 1.885,0.219 2.156,0.396 0.271,0.177 10 false *1 5.417,0.313 5.688,0.49 0.271,0.177 10 false *a 2.563,0.323 2.833,0.5 0.271,0.177 10 false *a 6.031,0.208 6.302,0.385 0.271,0.177 10 false *1 5.74,2.5 6.01,2.677 0.271,0.177 10 false *1 2,2.5 2.271,2.677 0.271,0.177 10 false *1

Text in Illustration
*1 SST - -
*a 45° - -


l.
A362230E01
2.028,0.35 2.300,0.531 0.272,0.181 10 *1 2.423,1.4 2.695,1.582 0.272,0.181 10 *1 0.967,0.737 1.239,0.918 0.272,0.181 10 *a 1.578,0.779 1.786,0.441 1.786,0.441 1.975,0.441 false 1.972,2.303 2.199,1.506 2.199,1.506 2.388,1.506 false

Using SST, carefully apply the thermal grease smoothly and evenly by spreading it as shown in the illustration. (Procedure C)

Text in Illustration
*1 SST
*a 45°


m.

Repeat steps A through C until the thermal grease is smooth and even.


n.
A362232

Check that the thermal grease has been applied smoothly and evenly.


o.
A300967

If the thermal grease layer is uneven and the application surface is visible, apply more thermal grease.


p.

Using SST, carefully apply the thermal grease smoothly and evenly.

NOTICE:
·

Apply the thermal grease smoothly and evenly to ensure proper heat transfer.

·

Keep SST at a 45-degree angle and perform work carefully.




q.
A300968

If foreign matter has attached to the thermal grease, scrape it off using the edge of the thermal grease tube, and apply more thermal grease.


r.

Using SST, carefully apply the thermal grease smoothly and evenly.

NOTICE:
·

Apply the thermal grease smoothly and evenly to ensure proper heat transfer.

·

Keep SST at a 45-degree angle and perform work carefully.




s.

Check that the thermal grease has been applied smoothly and evenly.


t.
A362233E02
1.146,2.74 1.208,3.094 1.208,3.094 1.396,3.094 false 0.406,1.365 0.719,0.26 0.719,0.26 0.906,0.26 false 1.427,3.021 1.698,3.198 0.271,0.177 10 false *1 0.948,0.156 1.135,0.333 0.188,0.177 10 false *1 2.719,1.885 2.885,2.052 0.167,0.167 10 false *a

Remove the masking seal from the hybrid vehicle converter kit.

Text in Illustration
*1 Bus-bar
*a Remove

NOTICE:
·

Slowly remove the masking seal without touching the thermal grease surface.

·

Be careful not to touch the bus-bars when removing the masking seal.




u.

Remove the protective tape.


v.

Align the guide holes with the guide pins as shown in the illustration, and temporarily install the power module intelligent transistor kit to the hybrid vehicle converter kit.

A360162E02
6.25,1.083 6.458,0.302 6.458,0.302 6.625,0.302 false 1.125,1.354 1.417,0.365 1.417,0.365 1.656,0.365 false 1.115,1.906 1.26,2.365 1.26,2.365 1.698,2.365 false 6.26,1.896 6.49,2.438 6.49,2.438 6.677,2.438 false 1.729,0.281 2,0.458 0.271,0.177 10 false *2 1.729,2.292 2,2.469 0.271,0.177 10 false *1 6.698,2.354 6.969,2.531 0.271,0.177 10 false *1 6.646,0.208 6.917,0.385 0.271,0.177 10 false *3

Text in Illustration
*1 Guide Pins *2 Guide Hole (Oblong Hole)
*3 Guide Hole (Circular Hole) - -

NOTICE:
·

Do not apply any force the coolant pipes.

·

Make sure to align the guide pins correctly.

·

Be careful not to deform the bus-bars.




w.

Install the power module intelligent transistor kit with the 4 bolts.


x.
A359881E02
0.24,0.573 0.448,0.771 0.208,0.198 10 false 1 0.104,2.042 0.313,2.24 0.208,0.198 10 true 2 3.021,2.25 3.229,2.448 0.208,0.198 10 false 4 3.021,0.99 3.229,1.188 0.208,0.198 10 true 3

Temporarily tighten the 4 bolts evenly in several steps in the order shown in the illustration, then fully tighten them.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


y.
A359880

Install the 3 bolts.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)

NOTICE:

Do not touch the bus-bars.



Hide 8.INSTALL MG CONTROL COMPUTER WITH BRACKET SUB-ASSEMBLY

NOTICE:
·

Do not touch the circuit board.

·

Do not allow any moisture to come into contact with the circuit board.



a.

Align the guide pins of the MG control computer with bracket sub-assembly with the holes of the hybrid vehicle converter kit and temporarily install the MG control computer with bracket sub-assembly to the hybrid vehicle converter kit.

A360163E02
2.208,1.417 2.74,1.417 false 1.99,3.688 3.198,4.375 3.198,4.375 3.313,4.375 false 2.76,1.333 2.99,1.563 0.229,0.229 10 false *1 3.396,4.292 3.625,4.521 0.229,0.229 10 false *1

Text in Illustration
*1 Guide Pins - -

NOTICE:

Make sure to align the guide pins correctly.



b.

Install the MG control computer with bracket sub-assembly with the 4 bolts.


c.
A359878E02
0.76,0.427 0.896,0.594 0.135,0.167 10 false 3 0.104,2.688 0.24,2.854 0.135,0.167 10 false 4 2.229,2.813 2.365,2.979 0.135,0.167 10 false 1 2.219,0.448 2.354,0.615 0.135,0.167 10 false 2

Temporarily tighten the 4 bolts evenly in several steps in the order shown in the illustration, then fully tighten them.

Torque:
4.5 N*m (46 kgf*cm, 40 in.*lbf)


d.

Engage the 2 wire harnesses to the 4 clamps.

A360164


e.
A359879

Connect the connector.


f.
A359876

Connect the 2 connectors.


g.
A359875

Disengage the lock claws of the white resin connector and connect the flat cable to the power module intelligent transistor kit.


h.

Check that the flat cable is connected securely.

NOTICE:
A317060

If the flat cable is not fully connected, connect it securely.



i.
A360165E01
2.903,0.248 3.175,0.430 0.272,0.181 10 *1 2.122,0.761 2.573,0.343 2.573,0.343 2.88,0.343 false

If the gasket of the inverter signal connector is protruding, fully push it in.

Text in Illustration
*1 Gasket

HINT:
A317062E03
1.833,0.625 1.979,0.208 1.979,0.208 2.104,0.208 false 2.854,1.094 3.083,1.094 false 0.573,1.094 0.802,1.094 false 1.104,0.635 1.271,0.281 1.271,0.281 1.406,0.281 false 1.833,1.542 2,1.979 2,1.979 2.104,1.979 false 2.115,1.896 2.385,2.073 0.271,0.177 10 false *2 2.125,0.115 2.396,0.292 0.271,0.177 10 false *2 3.104,1.021 3.313,1.198 0.208,0.177 10 false *2 0.365,1.021 0.573,1.198 0.208,0.177 10 false *2 1.427,0.188 1.698,0.365 0.271,0.177 10 false *1

If the gasket is misaligned, install it so that each mark is at the center of each side.

Text in Illustration
*1 Gasket
*2 Mark



Hide 9.INSTALL INVERTER TERMINAL WITH SENSOR SUB-ASSEMBLY

NOTICE:
·

Do not touch the circuit board.

·

Do not allow any moisture to come into contact with the circuit board.



a.

Align the guide pins of the inverter terminal with sensor sub-assembly with the holes of the hybrid vehicle converter kit and temporarily install the inverter terminal with sensor sub-assembly to the hybrid vehicle converter kit.

A360166E03
5.927,1.208 5.344,2.427 5.344,2.427 5.208,2.427 false 0.927,1.469 1.344,2.354 1.344,2.354 1.438,2.354 false 5.021,2.344 5.208,2.51 0.188,0.167 10 false *1 1.469,2.281 1.656,2.448 0.188,0.167 10 false *1

Text in Illustration
*1 Guide Pins - -

NOTICE:

Make sure to align the guide pins correctly.



b.

Install the inverter terminal with sensor sub-assembly with the 4 bolts.


c.
A359874E02
3.01,1.073 3.177,1.281 0.167,0.208 10 true 1 3.156,0.156 3.292,0.344 0.135,0.188 10 false 4 0.406,0.073 0.542,0.26 0.135,0.188 10 false 3 0.198,0.688 0.333,0.875 0.135,0.188 10 false 2

Temporarily tighten the 4 bolts evenly in several steps in the order shown in the illustration, then fully tighten them.

Torque:
4.5 N*m (46 kgf*cm, 40 in.*lbf)


d.
A359872

Connect the 3 connectors.


e.
A408792

Check that the 6 connectors and flat cable are connected securely as shown in the illustration.


f.

Check the installation condition of the pen sheet.

NOTICE:
·

Do not touch the circuit board.

·

Do not allow any moisture to come into contact with the circuit board.



i.

While ensuring that the pen sheet does not interfere with components of the circuit board, insert the pen sheet between the inverter terminal with sensor sub-assembly and MG control computer with bracket sub-assembly.

A360167E01
2.915,2.418 3.187,2.599 0.272,0.181 10 *1 2.545,2.044 2.737,2.493 2.737,2.493 2.889,2.493 false 5.903,2.399 6.175,2.580 0.272,0.181 10 *1 5.467,2.018 5.699,2.468 5.699,2.468 5.881,2.468 false

Text in Illustration
*1 Pen Sheet - -


ii.
A360168E02
2.719,2.458 3.01,2.885 3.01,2.885 3.146,2.885 false 2.896,0.948 3.031,1.667 3.031,1.667 3.177,1.667 false 2.135,0.656 1.469,0.396 1.469,0.396 1.281,0.396 false 1.646,2.125 1.781,1.781 1.781,1.781 1.969,1.781 false 3.198,2.823 3.396,3 0.198,0.177 10 false *1 3.208,1.594 3.365,1.771 0.156,0.177 10 false *1 1.052,0.313 1.25,0.49 0.198,0.177 10 false *2 1.99,1.708 2.188,1.885 0.198,0.177 10 false *3

Set the pen sheet so that the guide hole is aligned with the pin of the motor generator control computer sub-assembly as shown in the illustration.

Text in Illustration
*1 Guide Pin
*2 Double-sided Tape
*3 Pen Sheet


iii.

Attach the double-sided tape of the pen sheet to the connector as shown in the illustration.



g.
A359873

Install the 6 bolts.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)

NOTICE:

Do not touch the bus-bars.



Hide 10.INSTALL INVERTER CASE WITH CONDENSER

NOTICE:
·

Do not touch the circuit board.

·

Do not allow any moisture to come into contact with the circuit board.

·

Do not touch or allow grease or oil to contact the sealing surfaces of the hybrid vehicle converter kit and inverter case with condenser.



a.

Apply seal packing (diameter: 2.0 to 3.0 mm (0.0787 to 0.118 in.)) in a continuous line to the locations shown in the illustration.

A360169E02
0.99,2.104 1.031,2.406 1.031,2.406 1.177,2.406 false 0.854,1.417 0.74,0.948 0.74,0.948 0.625,0.948 false 5.583,0.74 5.583,0.938 false 6.646,0.74 6.646,0.938 false 6.177,0.563 6.292,0.417 6.292,0.417 6.406,0.417 false 4.688,1.135 4.927,1.573 4.927,1.573 5.083,1.573 false 2.292,1.875 1.958,2.5 1.958,2.5 2.115,2.5 false 1.208,2.323 1.479,2.5 0.271,0.177 10 false *1 0.438,0.875 0.708,1.052 0.271,0.177 10 false *2 2.271,0.719 2.542,0.896 0.271,0.177 10 false *2 6.115,1.625 6.385,1.802 0.271,0.177 10 false *a 5.438,0.198 5.708,0.375 0.271,0.177 10 false *c 5.615,2.156 5.885,2.333 0.271,0.177 10 false *b 4.115,2.292 4.385,2.469 0.271,0.177 10 true *2 4.656,0.625 4.927,0.802 0.271,0.177 10 false *2 2.385,2.292 2.656,2.469 0.271,0.177 10 false *2 6.417,0.344 6.688,0.521 0.271,0.177 10 false *3 5.51,0.958 5.781,1.135 0.271,0.177 10 false *1 6.583,0.958 6.854,1.135 0.271,0.177 10 false *1 2.26,1.531 2.531,1.708 0.271,0.177 10 false *2 5.115,1.479 5.385,1.656 0.271,0.177 10 false *3 2.135,2.427 2.406,2.604 0.271,0.177 10 false *3

Text in Illustration
*1 Seal Packing *2 Bolt Hole
*3 Coolant Pipe - -
*a 2.0 to 3.0 mm (0.0787 to 0.118 in.) *b 2.0 to 3.0 mm (0.0787 to 0.118 in.)
*c Around Coolant Pipe - -

Seal Packing:

Toyota Genuine Seal Packing 1282B, Three Bond 1282B or equivalent


NOTICE:
·

Install the inverter case with condenser within 3 minutes of applying seal packing.

·

Tighten the bolts within 15 minutes of applying seal packing.

·

Keep the coolant pipes free from seal packing.




b.

Install the inverter case with condenser.

i.
A360170E02
1.75,0.271 1.885,0.156 1.885,0.156 2.042,0.156 false 2.656,1.563 2.958,1.854 2.958,1.854 3.104,1.854 false 0.656,1.844 0.854,1.844 0.854,1.844 1.063,1.49 false 2.094,0.094 2.406,0.292 0.313,0.198 10 false *1 3.146,1.781 3.427,1.979 0.281,0.198 10 false *1 0.479,1.76 0.76,1.958 0.281,0.198 10 false *1

Peel back the protective tape to the extent that the following steps can be performed.

Text in Illustration
*1 Protective Tape

NOTICE:

Do not touch or allow grease or oil to contact the sealing surfaces of the inverter case with condenser.



ii.

Align the holes of the inverter case with condenser with the guide pins of the hybrid vehicle converter kit and temporarily install the inverter case with condenser so that the bus-bar (A) does not contact the protrusion of the inverter terminal with sensor sub-assembly (B).

A360171E01
2.295,2.29 2.567,2.472 0.272,0.181 10 *1 1.521,1.752 2.102,2.37 2.102,2.37 2.274,2.37 false 6.791,2.23 7.063,2.411 0.272,0.181 10 *1 5.694,1.839 6.525,2.309 6.525,2.309 6.77,2.309 false 6.182,0.134 6.455,0.315 0.272,0.181 10 A 4.585,1.234 4.823,1.415 0.239,0.181 10 B 5.155,0.378 5.81,0.205 5.81,0.205 6.141,0.205 false 4.945,0.819 4.627,1.096 4.627,1.096 4.627,1.207 false

Text in Illustration
*1 Guide Pins - -

NOTICE:
·

Make sure to align the guide pins correctly.

·
A360172

Check that the bus-bars of the hybrid vehicle converter kit overlap the bus-bars of the inverter case with condenser.

·
A360173E01
2.066,1.277 2.338,1.458 0.272,0.181 10 *1 1.77,1.122 1.887,1.377 1.887,1.377 2.03,1.377 false

Make sure that the bus-bar (A) is not resting on the resin part of the inverter terminal with sensor sub-assembly as shown in the illustration.



Text in Illustration
*1 Bus-bar (A)



c.
A359778

Temporarily install the inverter case with condenser with the 11 bolts.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


d.

Fully tighten the 11 bolts.

Torque:
9.2 N*m (94 kgf*cm, 81 in.*lbf)


e.
A359776

Install the 5 bolts.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)

NOTICE:

Do not touch the bus-bars.



Hide 11.INSTALL INVERTER UNION GROMMET

a.
A315660E01
1.895,0.197 2.167,0.379 0.272,0.181 10 *1 1.44,0.965 1.62,0.307 1.62,0.307 1.849,0.307 false

Apply a light coat of seal packing to 2 new inverter union grommets.

Text in Illustration
*1 Seal Packing

Seal Packing:

Toyota Genuine Seal Packing 1282B, Three Bond 1282B or equivalent


NOTICE:
·

Install the inverter union grommets within 60 minutes of installing the inverter case with condenser.

·

Apply a light coat of seal packing to the entire surface of the area shown in the illustration. If seal packing is applied excessively, it may seep out, however, sealing quality will not be affected.

·

Install the inverter union grommets within 3 minutes of applying seal packing.




b.
A360174E03
1.76,0.917 2.323,0.24 2.323,0.24 2.646,0.24 false 1.604,1.354 1.417,1.552 1.417,1.552 1.24,1.552 false 1.563,3.073 1.365,3.271 1.365,3.271 1.198,3.271 false 2,1.302 2.104,1.5 2.104,1.5 2.24,1.5 false 1.927,2.521 2.365,2.104 2.365,2.104 2.625,2.104 false 1.875,2.781 2.01,3.146 2.01,3.146 2.479,3.146 false 1.031,1.479 1.302,1.656 0.271,0.177 10 false *1 2.677,0.156 2.948,0.333 0.271,0.177 10 false *a 2.26,1.427 2.531,1.604 0.271,0.177 10 false *2 2.542,3.042 2.813,3.219 0.271,0.177 10 false *a 2.698,2.031 2.969,2.208 0.271,0.177 10 false *2 1,3.177 1.271,3.354 0.271,0.177 10 false *1

Push in the inverter union grommet until it passes over the flange of the coolant pipe.

Text in Illustration
*1 Coolant Pipe
*2 Inverter Union Grommet
*a Flange

NOTICE:

Do not damage the coolant pipes.



c.
A360175E01
2.621,0.553 2.894,0.735 0.272,0.181 10 *1 2.226,1.053 2.441,0.651 2.441,0.651 2.565,0.651 false

Using a 30 mm socket, install the inverter union grommet.

Text in Illustration
*1 30 mm Socket

HINT:
A360176E01
2.485,1.939 2.757,2.121 0.272,0.181 10 *a

Make sure that the clearance between the inverter union grommet and inverter case with condenser is 2.0 mm (0.0787 in.) or less.

Text in Illustration
*a 2.0 mm (0.0787 in.) or less



d.

Perform the same procedure to install the other inverter union grommet.


Hide 12.INSTALL NO. 1 AND NO. 2 INVERTER DRAIN PLUGS

NOTICE:

Do not touch or allow grease or oil to contact the sealing surfaces of the inverter case with condenser.


a.
A348655E03
2.052,1.323 2.156,1.583 2.156,1.583 2.365,1.583 false 2.01,2.667 2.125,2.958 2.125,2.958 2.313,2.958 false 2.406,1.51 2.635,1.698 0.229,0.188 10 false *1 2.365,2.875 2.594,3.063 0.229,0.188 10 false *1

Make sure that the sealing surfaces of the No. 1 and No. 2 inverter drain plugs are covered with aluminum tape.

Text in Illustration
*1 Aluminum Tape

NOTICE:

If the sealing surfaces of the No. 1 and No. 2 inverter drain plugs are not covered with aluminum tape, do not use them as they cannot be securely installed with only seal packing.



b.
A350409E03
0.813,1.135 0.927,1.448 0.927,1.448 1.135,1.448 false 0.99,2.75 1.135,3.073 1.135,3.073 1.313,3.073 false 1.146,1.344 1.5,1.615 0.354,0.271 10 false *1 1.344,2.969 1.698,3.24 0.354,0.271 10 false *1

Remove the release film from the No. 1 and No. 2 inverter drain plugs.

Text in Illustration
*1 Release Film


c.
A315650E03
1.927,0.427 2.094,0.156 2.094,0.156 2.25,0.156 false 2.094,1.979 2.229,1.729 2.229,1.729 2.406,1.729 false 2.26,0.917 2.396,1.115 2.396,1.115 2.531,1.115 false 0.875,1.729 0.771,1.5 0.771,1.5 0.615,1.5 false 2.281,0.063 2.552,0.24 0.271,0.177 10 false *1 0.417,1.406 0.688,1.583 0.271,0.177 10 false *2 2.542,1.031 2.813,1.208 0.271,0.177 10 false *3 2.417,1.635 2.688,1.813 0.271,0.177 10 false *3 2.844,2.167 3.115,2.344 0.271,0.177 10 false *a 2.469,2.792 2.74,2.969 0.271,0.177 10 false *b

Apply seal packing (diameter: 3.0 mm (0.118 in.)) to new No. 1 and No. 2 inverter drain plugs.

Text in Illustration
*1 No. 1 Inverter Drain Plug
*2 No. 2 Inverter Drain Plug
*3 Seal Packing
*a Approximately 3.0 mm (0.118 in.)
*b Approximately 3.0 mm (0.118 in.)

Seal Packing:

Toyota Genuine Seal Packing 1282B, Three Bond 1282B or equivalent


NOTICE:
·

Be sure to use the specified type of seal packing.

·

Install the No. 1 and No. 2 inverter drain plugs within 3 minutes of applying seal packing.




d.
A360177E01
0.654,1.743 0.927,1.924 0.272,0.181 10 *1 2.675,1.753 2.947,1.934 0.272,0.181 10 *2 1.151,1.364 1.013,1.832 1.013,1.832 0.862,1.832 false 2.41,1.482 2.534,1.854 2.534,1.854 2.663,1.854 false

Install the No. 1 and No. 2 inverter drain plugs to the inverter with converter assembly.

Text in Illustration
*1 No. 1 Inverter Drain Plug
*2 No. 2 Inverter Drain Plug


Hide 13.INSTALL INVERTER SIGNAL CONNECTOR COVER

a.
A314639E03
1.247,0.089 1.520,0.271 0.272,0.181 10 A 1.795,0.502 1.577,0.178 false 1.577,0.178 1.434,0.178 false 2.181,0.003 2.454,0.185 0.272,0.181 10 *1

Install the gasket to the inverter signal connector cover.

HINT:

Make sure that the protrusion (A) of the gasket is securely inserted into the groove of the inverter signal connector cover.


Text in Illustration
*1 Gasket


b.

Clean the installation surface.


c.
A359770E01
0.336,0.133 0.497,0.314 0.161,0.181 10 *1 0.566,0.238 0.895,0.703 false

Install the inverter signal connector cover with the 4 bolts.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)

Text in Illustration
*1 Inverter Signal Connector Cover


Hide 82112B 14.INSTALL NO. 2 ENGINE ROOM WIRE

a.
A359775

Engage the clamp.


b.

Install the No. 2 engine room wire to the inverter with converter assembly with the nut.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)

NOTICE:

Check that the nut is not cross-threaded and the terminal is not loose.



c.
A359774

Close the terminal cover and engage the 2 claws.


Hide G9221 15.INSTALL INVERTER COVER

a.
A360178E02
0.594,0.729 0.281,0.354 0.281,0.354 0.698,0.5 false 2.438,0.688 2.573,0.156 2.573,0.156 2.719,0.156 false 2.271,1.406 2.531,1.865 2.531,1.865 2.802,1.865 false 0.083,0.25 0.354,0.427 0.271,0.177 10 false *1 2.854,1.792 3.125,1.969 0.271,0.177 10 false *1 2.76,0.094 3.031,0.271 0.271,0.177 10 false *1

Remove the protective tape.

Text in Illustration
*1 Protective Tape


b.
A359767

Temporarily install the inverter cover with the 7 bolts to prevent any foreign matter or water from entering the inverter with converter assembly.

NOTICE:

Visually confirm that the inverter cover waterproofing rubber is securely installed before installing the inverter cover.



Hide G9223 16.INSTALL INVERTER TERMINAL COVER

a.
A359766E01
2.679,0.675 2.91,0.941 false 2.949,0.88 3.195,1.126 0.246,0.246 12 *1

Temporarily install the inverter terminal cover to the inverter with converter assembly with the 2 bolts.

Text in Illustration
*1 Interlock Connector

NOTICE:
·

Visually confirm that the inverter terminal cover waterproofing rubber is securely installed before installing the inverter terminal cover.

·

Make sure that the interlock connector is fully engaged.




Hide G9200 17.INSTALL INVERTER WITH CONVERTER ASSEMBLY

Hide 18. CHECK FOR COOLANT LEAK (for Inverter)

a.

Remove the reserve tank cap.

CAUTION:

Do not remove the reserve tank cap while the coolant (for inverter) is still hot. Pressurized, hot coolant and steam may be released and cause serious burns,



b.
A266680

Install the radiator cap tester.


c.

Pump the radiator cap tester to 122 kPa (1.2 kgf/ cm2, 17.7 psi), and then check that the pressure does not drop.

HINT:

If the pressure drops, check the hoses, radiator, water pump, inverter with converter, and hybrid vehicle transaxle assembly for leaks.



d.

Install the reserve tank cap.


Hide 19. OPERATION CHECK

HINT:
·

After performing repair, check the operation as follows. Then check for DTCs again.

·

The current at the AMD terminal cannot be measured directly because of space limitations. Measure the current flow at the auxiliary battery instead.



a.
A174427E07
0.646,0.99 0.823,0.615 0.823,0.615 0.938,0.615 false 0.979,0.542 1.552,0.906 0.573,0.365 10 Probe Direction 0.167,1.646 1.406,2.156 1.24,0.51 10 Current Flowing into Auxiliary Battery

Connect an AC/DC 400 A probe from an ammeter to the positive (+) auxiliary battery cable.


b.

Turn the power switch on (READY) and leave the vehicle as is until the electric current flowing into the auxiliary battery becomes 10 A or less.


c.
A174428E05
0.698,0.844 0.885,0.479 0.885,0.479 1,0.479 false 1.073,0.385 1.667,0.729 0.594,0.344 10 Probe Direction 0.208,1.531 1.208,2.042 1,0.51 10 Current Flowing from Auxiliary Battery

Change the orientation of the AC/DC 400A probe.


d.

Measure the current flowing from the auxiliary battery with the power switch on (READY), the high beam headlights on and blower motor switch in the HI position, and rear window defogger turned on.

Standard Current:
Item Switch Condition Specified Condition
Current flowing from auxiliary battery Power switch on (READY)
(High beam headlights on and blower motor switch in HI position, rear window defogger on)
0 A or less
(No current from auxiliary battery)



e.

Turn the power switch off.