Home › Engine / Hybrid System › 1NZ-FXE FUEL › FUEL PUMP › 2011.12–2015.11
RM2170E _51 Engine / Hybrid System _057006 1NZ-FXE FUEL _0277955 FUEL PUMP A

1NZ-FXE FUEL  FUEL PUMP  INSTALLATION  


PROCEDURE

Hide 77020A 1.INSTALL FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

a.
A265014E01
2.702,0.133 2.876,0.306 0.174,0.174 10 *1 2.458,0.343 2.582,0.219 2.582,0.219 2.666,0.219 false

Install a new fuel suction tube set gasket onto the fuel tank as shown in the illustration.

Text in Illustration
*1 Fuel Suction Tube Set Gasket


b.
A406616C01
1.135,0.823 1.135,0.385 1.135,0.385 1.219,0.385 true 0.875,2.552 1.802,2.552 true 1.271,0.313 1.583,0.469 0.313,0.156 10 false *a 0.698,2.479 1.01,2.635 0.313,0.156 10 false *b
*a Protrusion
*b Notch


Set the fuel suction tube with pump and gauge assembly to the fuel tank.

NOTICE:

Make sure that the fuel sender gauge arm does not bend.



c.

Align the protrusions of the fuel suction tube with pump and gauge assembly with the notches of the fuel tank.


Hide 77144 2.INSTALL FUEL PUMP GAUGE RETAINER

a.
A265017E02
1.219,0.49 0.979,0.25 0.979,0.25 0.854,0.25 false 1.302,0.583 0.865,0.583 false 0.656,0.146 0.823,0.313 0.167,0.167 10 false *a 0.656,0.479 0.823,0.646 0.167,0.167 10 false *b 1.469,1.854 1.635,2.021 0.167,0.167 10 false *c

While holding the fuel suction tube assembly with pump and gauge by hand to prevent it from tilting, align the mark on a new fuel pump gauge retainer with the start mark on the fuel tank and tighten the fuel pump gauge retainer 180° by hand.

Text in Illustration
*a Start Mark
*b Mark
*c Front

HINT:
·

Check that there is no damage, dents, foreign matter or other defects on the threads of the fuel tank.




b.
A265011E01
1.997,2.413 2.122,2.538 2.122,2.538 2.545,2.538 false 1.697,2.774 1.998,2.774 false 1.443,2.925 1.162,3.206 false 1.622,3.032 1.448,3.206 1.448,3.206 0.857,3.206 false 2.576,2.446 2.749,2.600 0.173,0.154 10 *1 2.037,2.673 2.209,2.827 0.173,0.154 10 *2 0.652,3.099 0.824,3.253 0.173,0.154 10 *3

Temporarily install the SST plate and claws to the fuel pump gauge retainer.

Text in Illustration
*1 SST
(Plate)
*2 SST
(Claw)
*3 Rib

SST
09808-14030  (09808-01030, 09808-01040, 09808-01050)

HINT:

Engage the SST claws securely with the fuel pump gauge retainer ribs to secure SST.



c.

While pressing the claws of SST to the fuel pump gauge retainer ribs securely, tighten the bolts.

HINT:

Install SST while pressing the SST claws toward the fuel pump gauge retainer (toward the center of SST).



d.

Install the SST handle.


e.
A265018E02
1.073,1.354 0.51,1.906 0.51,1.906 0.417,1.906 true 1.865,0.802 2.083,0.573 2.083,0.573 2.26,0.573 false 2.156,3.896 2.615,3.625 2.615,3.625 2.729,3.625 false 0.865,0.729 1.375,0.229 1.375,0.229 1.49,0.229 false 2.76,3.542 2.927,3.792 0.167,0.25 10 false *a 1.396,4.344 1.583,4.563 0.188,0.219 10 false *b 1.531,0.146 1.698,0.396 0.167,0.25 10 false *1 0.229,1.823 0.396,2.073 0.167,0.25 10 false *3 2.302,0.49 2.469,0.74 0.167,0.25 10 false *2

Tighten the fuel pump gauge retainer approximately 360° so that the mark on the retainer comes within the range shown in the illustration.

Text in Illustration
*1 SST
(Handle)
*2 SST
(Plate)
*3 SST
(Claw)
*a Mark
*b Front

SST
09808-14030  (09808-01010, 09808-01020, 09808-01030, 09808-01040, 09808-01050)

NOTICE:
·

Do not use any tools other than specified in this operation. Damage to the fuel pump gauge retainer or the fuel tank may result.

·

Do not press down on SST excessively as this may make the retainer hard to rotate, and may damage components.

·

Make sure to rotate the SST handle horizontally. If the SST handle is rotated at an angle, SST may come off.

·

Do not spin SST too fast or use an impact wrench as this may result in damage to components.

·

If SST comes off of the retainer, loosen the SST bolts and reinstall SST.



HINT:
·

Lightly press down on SST to prevent it from separating from the retainer. While pressing SST, rotate the handle slowly to tighten the retainer.

·

The ribs on the fuel pump gauge retainer can be fitted into the tips of SST.




Hide 77701W 3.CONNECT NO. 1 CANISTER OUTLET HOSE SUB-ASSEMBLY

a.
A265010

Connect the No. 1 charcoal canister outlet hose to the fuel suction tube with pump and gauge assembly.


Hide 77262 4.CONNECT NO. 2 FUEL EMISSION TUBE

a.
A265009

Connect the No. 2 fuel emission tube to the fuel suction tube with pump and gauge assembly with the clip.


Hide 77209F 5.CONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.
A388954E01
2.688,2.177 2.688,2.51 true 2.604,2.521 2.917,2.719 0.313,0.198 10 false *1

A388955E01
0.25,1.729 1.667,3.198 1.417,1.469 1.76,1.729 3.177,3.198 1.417,1.469 1.26,0.406 1.677,0.406 false 2.313,0.688 2.646,0.688 false 2.052,0.854 2.552,0.854 2.552,0.854 2.552,1.188 false 2.01,1 2.552,1 false 1.167,2.333 1.438,2.333 false 2.531,2.417 2.948,2.417 false 2.25,2.406 2.76,2.125 2.76,2.125 2.927,2.125 false 0.906,2.458 1.292,2.896 1.292,2.896 1.458,2.896 false 1.073,0.323 1.385,0.521 0.313,0.198 10 false *2 2.698,0.594 3.01,0.792 0.313,0.198 10 false *1 2.479,1.208 2.792,1.406 0.313,0.198 10 false *3 0.313,1.75 0.625,1.948 0.313,0.198 10 false *a 1.813,1.75 2.125,1.948 0.313,0.198 10 false *b 1.49,2.26 1.802,2.458 0.313,0.198 10 false *1 1.51,2.802 1.823,3 0.313,0.198 10 false *4 2.969,2.323 3.281,2.521 0.313,0.198 10 false *1 2.969,2.063 3.281,2.26 0.313,0.198 10 false *4

Push the fuel tube joint in the plug of the fuel suction plate, then install the tube joint clip.

Text in Illustration
*1 Tube Joint Clip
*2 Fuel Tube Joint
*3 O-ring
*4 Collar
*a CORRECT
*b INCORRECT

NOTICE:
·

Check that there is no damage or foreign matter around the connecting parts of the fuel tube joint and plug before performing this work.

·

Check that the fuel tube joint is securely inserted to the end.

·

Check that the tube joint clip is on the collar of the fuel tube joint.

·

After installing the tube joint clip, check that the fuel tube joint cannot be pulled out.




b.

Connect the fuel pump connector.


Hide 6.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 58325E 8.INSTALL REAR FLOOR SERVICE HOLE COVER

a.
A267868E01
2.892,0.107 3.097,0.353 0.205,0.246 10 *1 2.216,0.724 2.742,0.198 2.742,0.198 2.894,0.198 false

Install the rear floor service hole cover with new butyl tape.


Hide 73705B 9.INSTALL CROSS ANCHOR BRACKET SUB-ASSEMBLY