1.CHECK FUEL PUMP OPERATION AND INSPECT FOR FUEL LEAK
Check fuel pump operation.
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG) and turn the intelligent tester on.
Do not start the engine.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.
Check for pressure in the fuel inlet tube from the fuel line. Check that sounds of fuel flowing from the fuel tank can be heard. If no sounds can be heard, check the integration relay, fuel pump, ECM and wiring connectors.
Inspect for fuel leaks.
Check that there are no fuel leaks from the fuel system after doing any maintenance or repairs. If there is a fuel leak, repair or replace parts as necessary.
Turn the power switch off.
Disconnect the intelligent tester from the DLC3.
2.CHECK FUEL PRESSURE
Discharge the fuel system pressure (See page Engine / Hybrid System>1NZ-FXE FUEL>FUEL SYSTEM>PRECAUTION).
Using a voltmeter, measure the auxiliary battery voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Positive terminal - Negative terminal | Power switch off | 11 to 14 V |
Disconnect the cable from the negative (-) auxiliary battery terminal.
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
Disconnect the fuel pipe from the fuel main tube (See page Engine / Hybrid System>1NZ-FXE FUEL>FUEL SYSTEM>PRECAUTION).
Install SST (pressure gauge) using SST and a fuel tube connector as shown in the illustration.
| *1 | SST
(Hose Band) |
| *2 | SST
(T-joint) |
| *3 | SST
(Pressure Gauge) |
| *4 | SST
(Hose) |
| *5 | SST
(Fuel Tube Connector) |
| *6 | Fuel Tube |
| *7 | Fuel Pipe |
Wipe up any spilled gasoline.
Connect the cable to the negative (-) auxiliary battery terminal.
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
Connect the intelligent tester to the DLC3.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.
Measure the fuel pressure.
304 to 343 kPa (3.1 to 3.5 kgf/cm2, 44 to 50 psi)
If the fuel pressure is greater than the standard value, replace the fuel pressure regulator.
If the fuel pressure is less than the standard value, check the fuel hoses and connections, fuel pump, fuel filter and fuel pressure regulator.
Disconnect the intelligent tester from the DLC3.
Put the engine in inspection mode (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).
Start the engine.
Measure the fuel pressure at idle.
304 to 343 kPa (3.1 to 3.5 kgf/cm2, 44 to 50 psi)
Stop the engine.
Check that the fuel pressure remains as specified for 5 minutes after the engine stops.
147 kPa (1.5 kgf/cm2, 21 psi) or more
If the fuel pressure is not as specified, check the fuel pump, pressure regulator and/or fuel injectors.
After checking the fuel pressure, disconnect the cable from the negative (-) auxiliary battery terminal and carefully remove SST to prevent gasoline from spraying.
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
Reconnect the fuel pipe to the fuel main tube (fuel tube connector).
Install the No. 1 fuel pipe clamp to the fuel tube connector.
Check for fuel leaks (Step 1).
Check that there are no fuel leaks from the fuel system after doing any maintenance or repairs. If there is a fuel leak, repair or replace parts as necessary.