Home › Engine / Hybrid System › 1NZ-FXE INTAKE / EXHAUST › EXHAUST MANIFOLD › 2011.12–2017.06
RM2170E _51 Engine / Hybrid System _057008 1NZ-FXE INTAKE / EXHAUST _0277969 EXHAUST MANIFOLD A

1NZ-FXE INTAKE / EXHAUST  EXHAUST MANIFOLD  INSTALLATION  


PROCEDURE

Hide 17168 2.INSTALL NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

a.

Install the No. 2 exhaust manifold heat insulator with the 3 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 17141 3.INSTALL EXHAUST MANIFOLD

a.

Set a new gasket to the cylinder head sub-assembly.


b.

Temporarily install the exhaust manifold with the 3 bolts and 2 nuts.


c.

Temporarily install the manifold support bracket with the 3 bolts.


d.
A267694E03
1.604,0.229 1.771,0.396 0.167,0.167 10 true *1 0.604,1.458 0.771,1.625 0.167,0.167 10 true *1 2.573,1.448 2.74,1.615 0.167,0.167 10 true *1 3.156,0.333 3.323,0.5 0.167,0.167 10 true *2 0.146,0.365 0.313,0.531 0.167,0.167 10 true *2

Tighten the exhaust manifold with the 3 bolts and 2 nuts.

Text in Illustration
*1 Bolt
*2 Nut

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)


e.

Connect the wire harness clamp and heated oxygen sensor connector.


f.

Remove the 3 bolts and manifold support bracket.


Hide 25611A 4.INSTALL NO. 1 EGR PIPE

a.

Install a new gasket and No. 1 EGR pipe with the bolt and nut.

Torque:
31 N*m (316 kgf*cm, 23 ft.*lbf)


Hide 25591 5.INSTALL MANIFOLD SUPPORT BRACKET

a.
U159060E03
0.385,0.146 0.51,0.292 0.125,0.146 10 false A 1.885,0.302 2.01,0.448 0.125,0.146 10 false B 2.635,0.417 2.76,0.563 0.125,0.146 10 false A 3.021,1.25 3.146,1.396 0.125,0.146 10 false A

Install the manifold support bracket with the 4 bolts.

Torque:
Bolt A : 44 N*m (449 kgf*cm, 32 ft.*lbf)
Bolt B : 10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 17167 6.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

a.

Install the No. 1 exhaust manifold heat insulator with the 3 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 17410 8.INSTALL FRONT EXHAUST PIPE ASSEMBLY

a.
A077857

Using a vernier caliper, measure the free length of the compression springs.

Minimum (front) 41.5 mm (1.64 in.)
Minimum (rear) 38.5 mm (1.52 in.)

HINT:

If the free length is less than minimum, replace the compression spring.



b.

Fully insert 2 new gaskets to the exhaust manifold converter and front exhaust pipe assembly.


c.
A181728E17
1.074,0.399 1.283,0.621 0.209,0.223 10 *1 0.736,2.568 0.956,2.724 0.221,0.156 10 *2 2.726,1.902 2.949,2.042 0.223,0.140 10 *3 1.359,0.466 1.509,0.466 1.509,0.466 1.834,1.116 false 2.042,2.337 1.19,2.651 1.19,2.651 0.986,2.651 false 2.522,1.415 2.831,1.596 2.831,1.596 2.831,1.831 false

Using a plastic hammer and wooden block, tap in each new gasket until its surface is flush with the exhaust manifold and front exhaust pipe assembly.

Text in Illustration
*1 Exhaust Manifold and Front Exhaust Pipe Assembly
*2 Gasket
*3 Wooden Block

NOTICE:
·

Be careful with the installation direction of the gaskets.

·

Do not reuse the gaskets.

·

Do not damage the gaskets.

·

Do not push in the gaskets by using the exhaust pipe when connecting it.




d.

Connect the front exhaust pipe assembly to the 3 exhaust pipe supports.


e.

Install the front exhaust pipe assembly with the 2 compression springs, 2 bolts and 2 nuts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)

HINT:
A258941E01
0.543,0.102 0.692,0.251 0.149,0.149 10 *1 2.694,0.132 2.843,0.281 0.149,0.149 10 *3 0.605,1.113 0.754,1.263 0.149,0.149 10 *2 0.419,1.433 0.568,1.582 0.149,0.149 10 *a 1.146,0.584 0.883,0.184 0.883,0.184 0.733,0.184 false 0.79,1.195 0.925,1.195 0.925,1.195 1.112,0.903 false 2.411,0.76 2.503,0.215 2.503,0.215 2.676,0.215 false

After installation, check that the gaps between the flanges of the exhaust manifold and front exhaust pipe assembly are consistent front-to-rear and left-to-right.

Text in Illustration
*1 Exhaust Manifold
*2 Front Exhaust Pipe Assembly
*3 Gasket
*a Space between flanges: 8.5 mm (0.335 in.)



f.

Install the front exhaust pipe assembly with the 2 compression springs and 2 bolts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)

HINT:
A258966E01
0.714,0.328 0.870,0.476 0.156,0.148 10 *1 0.756,1.429 0.912,1.577 0.156,0.148 10 *2 2.843,0.368 2.999,0.516 0.156,0.148 10 *3 0.594,1.723 0.750,1.870 0.156,0.148 10 *a 1.366,0.938 1.095,0.404 1.095,0.404 0.9,0.404 false 1.329,1.162 1.13,1.515 1.13,1.515 0.94,1.515 false 2.248,0.916 2.621,0.448 2.621,0.448 2.827,0.448 false

After installation, check that the gaps between the flanges of the tail exhaust pipe assembly and front exhaust pipe assembly are consistent front-to-rear and left-to-right.

Text in Illustration
*1 Tail Exhaust Pipe Assembly
*2 Front Exhaust Pipe Assembly
*3 Gasket
*a Space between flanges: 6.5 mm (0.256 in.)



Hide 25680 9.INSTALL EGR COOLER ASSEMBLY

Hide 10.INSPECT FOR EXHAUST GAS LEAK