Home › Engine / Hybrid System › CRUISE CONTROL › CRUISE CONTROL SYSTEM › from 2014.12
RM2170E _51 Engine / Hybrid System _057012 CRUISE CONTROL _0277986 CRUISE CONTROL SYSTEM J

CRUISE CONTROL  CRUISE CONTROL SYSTEM  Cruise Control Switch Circuit  


DESCRIPTION

The cruise control switch is used to turn the cruise control system on and off, as well as operate 7 functions: SET, - (COAST), TAP-DOWN, RES (RESUME), + (ACCEL), TAP-UP and CANCEL. The SET, TAP-DOWN and - (COAST) functions, and the RES (RESUME), TAP-UP and + (ACCEL) functions are operated with the same switch. The cruise control switch is an automatic return type switch which turns on only while operating it in the direction of each arrow and turns off after releasing it. The internal contact points of the cruise control switch turn on with switch operation. Then the hybrid vehicle control ECU reads the voltage value that has been changed by the switch operation to control SET, - (COAST), RES (RESUME), + (ACCEL), and CANCEL.

WIRING DIAGRAM

B373913E08
6.344,0.427 6.688,0.583 0.344,0.156 10 false CCS 6.344,1.094 6.531,1.25 0.188,0.156 10 false E1 6.146,0.99 6.26,1.146 0.115,0.156 10 false 6 6.083,0.292 6.26,0.448 0.177,0.156 10 false 28 5.052,2.646 5.156,2.802 0.104,0.156 10 false 1 5.052,3.531 5.156,3.688 0.104,0.156 10 false 2 3.979,2.635 4.083,2.792 0.104,0.156 10 false 3 3.979,3.521 4.094,3.677 0.115,0.156 10 false 4 4.99,2.854 5.208,3.01 0.219,0.156 10 false G5 4.99,3.75 5.208,3.906 0.219,0.156 10 false G5 3.948,2.854 4.167,3.01 0.219,0.156 10 false z6 4.542,2.76 4.865,2.917 0.323,0.156 10 false CCS 6.177,4.927 7.104,5.323 0.927,0.396 10 false Hybrid Vehicle Control ECU 4.542,3.656 4.865,3.813 0.323,0.156 10 false ECC 3.948,3.75 4.115,3.906 0.167,0.156 10 false z6 1.146,4.26 2.615,4.417 1.469,0.156 10 false Cruise Control Switch 3.281,4.385 4.25,4.708 0.969,0.323 10 false Cruise Control Switch Wire 3.094,3.885 3.417,4.042 0.323,0.156 10 false ECC 3.094,2.75 3.417,2.906 0.323,0.156 10 false CCS 3.51,2.75 3.667,2.906 0.156,0.156 10 false 3 3.51,3.885 3.646,4.042 0.135,0.156 10 false 1 2.865,3.26 3.427,3.417 0.563,0.156 10 false ON-OFF 2.104,3.26 2.573,3.417 0.469,0.156 10 false +/RES 1.333,3.26 1.729,3.417 0.396,0.156 10 false -/SET 0.521,3.26 1.104,3.417 0.583,0.156 10 false CANCEL 4.26,4.25 5.625,4.615 1.365,0.365 10 false Spiral with Sensor Cable Sub-assembly 6.177,4.76 6.458,4.917 0.281,0.156 10 false G80

PROCEDURE

1.READ VALUE ON INTELLIGENT TESTER
E107091E29
2.219,0.156 2.49,0.344 0.271,0.188 10 false *c 2.854,1.26 3.094,1.458 0.24,0.198 10 false *a 2.063,1.635 2.448,1.833 0.385,0.198 10 false *b 0.99,1.271 1.229,1.469 0.24,0.198 10 false *d

a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the intelligent tester on.


d.

Select the following menu items: Powertrain / Cruise Control / Data List.


e.

Check the Data List to confirm proper functioning of the cruise control switch.

Text in Illustration
*a ON-OFF
*b -/SET
*c +/RES
*d CANCEL

Cruise Control
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Main SW M-CPU Cruise control switch signal (Main CPU) / ON or OFF ON: Cruise control switch (ON-OFF button) pushed
OFF: Cruise control switch (ON-OFF button) released
-
Cancel Switch CANCEL switch signal / ON or OFF ON: CANCEL switch on
OFF: CANCEL switch off
-
SET/COAST Switch -/SET switch signal / ON or OFF ON: -/SET switch on
OFF: -/SET switch off
-
RES/ACC Switch +/RES switch signal / ON or OFF ON: +/RES switch on
OFF: +/RES switch off
-
Main SW S-CPU Cruise control switch signal (Sub CPU) / ON or OFF ON: Cruise control switch (ON-OFF button) pushed
OFF: Cruise control switch (ON-OFF button) released
-

OK:

When the cruise control switch is operated, the display changes as shown above.




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT CRUISE CONTROL SWITCH
2.INSPECT CRUISE CONTROL SWITCH
a.

b.

Measure the resistance according to the value(s) in the table below.

E319149E01
5.344,1.125 5.969,0.323 5.969,0.323 6.135,0.323 false 0.281,0.125 0.594,0.323 0.313,0.198 10 false *a 4.76,0.5 5.073,0.698 0.313,0.198 10 false *c 6.198,0.24 6.51,0.438 0.313,0.198 10 false *1 6.208,1.208 6.521,1.406 0.313,0.198 10 false *b 5.146,2.417 5.458,2.615 0.313,0.198 10 false *d 3.979,2.052 4.292,2.25 0.313,0.198 10 false *e


Text in Illustration
*1 Cruise Control Switch (ON-OFF button) - -
*a Component without harness connected
(Cruise Control Switch)
*b ON-OFF
*c +/RES *d -/SET
*e CANCEL - -

Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 - 3 Cruise control switch (ON-OFF button) released 1 MΩ or higher
Cruise control switch (ON-OFF button) pushed Below 2.5 Ω
+/RES 235 to 245 Ω
-/SET 617 to 643 Ω
CANCEL 1509 to 1571 Ω



OK

3.CHECK CRUISE CONTROL SWITCH WIRE (SPIRAL CABLE SUB-ASSEMBLY - CRUISE CONTROL SWITCH)

NG

3.CHECK CRUISE CONTROL SWITCH WIRE (SPIRAL CABLE SUB-ASSEMBLY - CRUISE CONTROL SWITCH)
a.

Disconnect the spiral with sensor cable sub-assembly connector.


U159664E02
0.26,1.417 0.427,1.573 0.167,0.156 9 false z6 0.115,0.073 0.469,0.323 0.354,0.25 10 false *a 0.115,2.26 0.552,2.479 0.438,0.219 10 false *b

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Specified Condition
z6-3 - 3 Below 1 Ω
z6-4 - 1 Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Spiral with Sensor Cable Sub-assembly)
*b Front view of wire harness connector
(to Cruise Control Switch)



OK

4.CHECK SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY

NG

REPAIR OR REPLACE CRUISE CONTROL SWITCH WIRE (SPIRAL CABLE SUB-ASSEMBLY - CRUISE CONTROL SWITCH)

4.CHECK SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY
NOTICE:

The spiral with sensor cable sub-assembly is an important part of the SRS airbag system. Incorrect removal or installation of the spiral with sensor cable sub-assembly may prevent the airbag from deploying. Be sure to read the pages shown in the brackets.


HINT:


a.

Remove the spiral with sensor cable sub-assembly.


E343931E04
3.083,3.448 3.5,3.698 0.417,0.25 3.667,1.083 4.083,1.333 0.417,0.25 3.01,4.396 3.208,4.094 false 3.542,4.458 3.281,4.094 false 1.896,0.115 2.208,0.313 0.313,0.198 10 false *a 3.792,1.125 4.104,1.323 0.313,0.198 10 false z6 3.198,3.49 3.51,3.688 0.313,0.198 10 false G5 2.813,4.448 3.219,4.646 0.406,0.198 10 false CCS 3.448,4.469 3.854,4.667 0.406,0.198 10 false ECC

b.

Measure the resistance according to the value(s) in the table below.


Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
z6-3 - G5-1 (CCS) Center Below 3 Ω
2.5 rotations to the left
2.5 rotations to the right
z6-4 - G5-2 (ECC) Center Below 3 Ω
2.5 rotations to the left
2.5 rotations to the right


c.

After setting the spiral with sensor cable sub-assembly to the center position, rotate the spiral with sensor cable sub-assembly 2.5 times clockwise. Then while rotating the spiral with sensor cable sub-assembly 5 times counterclockwise, measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
z6-3 - G5-1 (CCS) Always Below 3 Ω
z6-4 - G5-2 (ECC) Always Below 3 Ω


Text in Illustration
*a Component without harness connected
(Spiral with Sensor Cable Sub-assembly)

HINT:

The spiral with sensor cable sub-assembly makes a maximum of approximately 5 rotations.




OK

5.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - SPIRAL CABLE SUB-ASSEMBLY)

NG

REPLACE SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - SPIRAL CABLE SUB-ASSEMBLY)
a.

Disconnect the G80 hybrid vehicle control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
G5-1 (CCS) - G80-28 (CCS) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
G5-1 (CCS) or G80-28 (CCS) - Body ground Always 10 kΩ or higher




OK

6.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - HYBRID VEHICLE CONTROL ECU)

6.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - BODY GROUND)
a.
U159627E01
0.153,0.106 0.402,0.319 0.249,0.213 10 *a 0.553,1.502 0.763,1.665 0.210,0.163 10 G5 0.957,2.244 1.292,2.407 0.334,0.163 10 ECC 1.476,1.591 1.129,2.229 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
G5-2 (ECC) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Spiral with Sensor Cable Sub-assembly)



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - BODY GROUND)