Home › Engine / Hybrid System › CRUISE CONTROL › CRUISE CONTROL SYSTEM › 2014.12–2015.11
RM2170E _51 Engine / Hybrid System _057012 CRUISE CONTROL _0277986 CRUISE CONTROL SYSTEM C

CRUISE CONTROL  CRUISE CONTROL SYSTEM  P1578  Brake System Malfunction  


DESCRIPTION

This DTC is output when the electronically controlled brake system has a problem. Check the electronically controlled brake system when this DTC is output.

DTC No. DTC Detection Condition Trouble Area
P1578 The hybrid vehicle control ECU receives a brake system error signal for 0.2 sec. or more while the cruise control is in operation
·

Electronically controlled brake system


·

Hybrid vehicle control ECU



WIRING DIAGRAM

E306619E05
2.094,0.594 2.708,0.792 0.615,0.198 10 false CA1H 2.125,1.104 2.74,1.302 0.615,0.198 10 false CA1L 4.948,0.573 5.563,0.771 0.615,0.198 10 false CA1H 4.948,1.073 5.563,1.271 0.615,0.198 10 false CA1L 2.615,0.417 3.229,0.615 0.615,0.198 10 false 37 2.625,0.917 3.24,1.115 0.615,0.198 10 false 38 4.656,0.396 5.271,0.594 0.615,0.198 10 false 25 4.667,0.906 5.281,1.104 0.615,0.198 10 false 24 0.823,1.563 1.438,1.76 0.615,0.198 10 false A41 0.823,1.74 3,2.302 2.177,0.563 10 false Brake Booster with Master Cylinder Assembly (Skid Control ECU) 0.854,2.458 3.885,2.781 3.031,0.323 10 false : CAN Communication Line 4.74,1.646 5.354,1.844 0.615,0.198 10 false G81 4.75,1.823 6.531,2.094 1.781,0.271 10 false Hybrid Vehicle Control ECU

CAUTION / NOTICE / HINT

HINT:

This circuit uses CAN communication. Therefore, if there are any malfunctions in the communication circuit, one or more DTCs in the CAN communication system are output.


PROCEDURE

1.CHECK DTC (ELECTRONICALLY CONTROLLED BRAKE SYSTEM)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Chassis / ABS/VSC/TRAC / Trouble Codes.


e.

Check for the DTC.

Result:
Result Proceed to
DTC is not output A
DTC is output B




A

2.CHECK FOR DTCs (DTC P1578)

B

2.CHECK FOR DTCs (DTC P1578)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the intelligent tester on.


d.

Perform the following to make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the malfunction cannot be detected.


i.

Drive the vehicle at a speed for which cruise control operation is possible.


ii.

Turn the cruise control system on using the ON-OFF switch.


iii.

Push the -/SET switch to activate the cruise control.



e.

Enter the following menus: Powertrain / Cruise Control / Trouble Codes.


f.

Check for DTCs.

Result:
Result Proceed to
DTC is not output A
DTC P1578 is output B




A

B

3.REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY
3.REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

Replace the brake booster with master cylinder (skid control ECU) (See page Brake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER(for LHD)>REMOVAL for LHD, Brake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER(for RHD)>REMOVAL for RHD).


NEXT

4.CHECK FOR DTCs (DTC P1578)
4.CHECK FOR DTCs (DTC P1578)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the intelligent tester on.



e.

Perform the following to make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the malfunction cannot be detected.


i.

Drive the vehicle at a speed for which cruise control operation is possible.


ii.

Turn the cruise control system on using the ON-OFF switch.


iii.

Push the -/SET switch to activate the cruise control.



f.

Enter the following menus: Powertrain / Cruise Control / Trouble Codes.


g.

Check for DTCs.

Result:
Result Proceed to
DTC is not output A
DTC P1578 is output B




A

END

B