Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE BOOSTER(for RHD) › from 2014.12
RM2170E _54 Brake _057022 BRAKE SYSTEM (OTHER) _0278029 BRAKE BOOSTER(for RHD) A

BRAKE SYSTEM (OTHER)  BRAKE BOOSTER(for RHD)  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 3.REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 55722C 4.REMOVE INNER COWL TOP TO COWL BRACE

a.
C249834

Remove the 3 bolts and inner cowl top to cowl brace.


Hide 55735B 5.REMOVE FRONT AIR SHUTTER SEAL

a.
C249836

Disengage the clamp to remove the front air shutter seal.


Hide 55815E 6.REMOVE FRONT NO. 1 VENTILATOR SEAL

a.
C249835

Disengage the clamp to remove the front No. 1 ventilator seal.


Hide 55701J 7.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY

a.
C256179

Disengage the 3 clamps to separate the wire harness from the outer cowl top panel sub-assembly.


b.
C249838

Remove the 8 bolts, nut and outer cowl top panel sub-assembly.


Hide 8.DRAIN BRAKE FLUID

NOTICE:

If brake fluid leaks onto any painted surface, immediately clean it off.


Hide 47220D 9.SEPARATE BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY

a.
C249839

Remove the 2 nuts and separate the brake master cylinder reservoir assembly from the reservoir bracket.


Hide 47235G 10.DISCONNECT NO. 2 RESERVOIR HOSE

a.
C249840

Move the clip and disconnect the No. 2 reservoir hose from the brake booster with master cylinder assembly.


Hide 47234L 11.DISCONNECT NO. 1 RESERVOIR HOSE

a.
C249842

Move the clip and disconnect the No. 1 reservoir hose from the brake booster with master cylinder assembly.


Hide 44572 12.SEPARATE NO. 2 BRAKE ACTUATOR HOSE

a.
C249844

Move the clip and disconnect the No. 2 brake actuator hose from the No. 1 brake actuator tube.


Hide 47220D 13.REMOVE BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY

Hide 47233 14.REMOVE RESERVOIR BRACKET

a.
C249846

Remove the bolt, nut and reservoir bracket.


Hide 47101A 15.REMOVE BRAKE PEDAL RETURN SPRING

Hide 17.DISCONNECT BRAKE LINE

a.
U162297E03
1.333,1.698 0.917,1.698 true 1.302,1.573 0.615,1.573 true 1.313,1.427 0.917,1.427 true 1.313,1.281 0.615,1.281 true 1.917,1.219 2.646,1.219 true 0.729,1.594 0.896,1.75 0.167,0.156 10 true *d 0.729,1.333 0.896,1.49 0.167,0.156 10 true *b 0.427,1.49 0.594,1.646 0.167,0.156 10 true *c 0.427,1.188 0.594,1.344 0.167,0.156 10 true *a 2.635,1.115 2.802,1.271 0.167,0.156 10 true *e

Using a union nut wrench, disconnect the 5 brake lines from the brake booster with master cylinder assembly.


b.

Use tags or make a memo to identify the places to reconnect the lines.

Text in Illustration
*a to Front Wheel Cylinder LH
*b to Rear Wheel Cylinder RH
*c to Brake Booster Pump Assembly
*d to Rear Wheel Cylinder LH
*e to Front Wheel Cylinder RH


c.
C249851

Disengage the brake tube clamp from the clamp bracket of the brake booster with master cylinder assembly.


Hide 47210L 18.REMOVE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

a.
C249849

Release the lock lever and disconnect the connector from the brake booster with master cylinder assembly.

Text in Illustration
V100135

Release the lock lever
V100136

Disconnect the connector


b.
C249829

Disengage the wire harness clamp from the stud bolt of the brake booster with master cylinder assembly.


c.
C249831E01
2.114,2.606 2.286,2.753 0.172,0.147 10 *1 0.413,2.931 0.585,3.078 0.172,0.147 10 *2 1.642,2.686 2.114,2.686 false 3.127,2.96 3.299,3.107 0.172,0.147 10 *3 2.732,3.04 3.127,3.04 false 2.807,3.247 2.979,3.395 0.172,0.147 10 *4 2.395,4.191 2.567,4.338 0.172,0.147 10 *5 2.412,3.327 2.807,3.327 false 1.648,3.292 0.612,3.027 0.612,3.027 1.259,3.463 false 1.714,3.914 2.352,4.27 2.352,4.27 1.51,4.269 false

Remove the 4 nuts and brake booster with master cylinder assembly.

Text in Illustration
*1 Connector Portion
*2 Union
*3 Brake Master Cylinder Push Rod Clevis
*4 Boot
*5 Front No. 2 Brake Tube

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not carry the brake booster with master cylinder assembly by the portion shown in bold in the illustration.

·

Be careful not to allow any brake fluid to enter the connector.




Hide 44785C 19.REMOVE BRAKE BOOSTER GASKET