Home › Drivetrain › P510 (HYBRID TRANSMISSION / TRANSAXLE) › SHIFT LEVER › 2011.12–2017.06
RM2170E _52 Drivetrain _057013 P510 HYBRID TRANSMISSION / TRANSAXLE _0277995 SHIFT LEVER A

P510 HYBRID TRANSMISSION / TRANSAXLE  SHIFT LEVER  INSTALLATION  


PROCEDURE

Hide 1.INSTALL SHIFT LEVER ASSEMBLY

a.

Engage the 2 clamps and connect the instrument panel wire to the shift lever assembly.


b.

Connect the 2 connectors to the shift lever assembly.


c.

Temporarily install the shift lever assembly with the 4 bolts.


d.
C251061E01
1.261,1.881 1.383,2.034 0.122,0.153 10 1 2.449,0.01 2.571,0.163 0.122,0.153 10 2 0.752,0.456 0.874,0.609 0.122,0.153 10 3 2.953,0.851 3.075,1.005 0.122,0.153 10 4

Fully tighten the 4 bolts in the order shown in the illustration.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 33820B 2.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

a.
C195134E07
0.729,1.938 1.24,1.625 false 2.885,0.667 2.219,0.906 false 0.521,1.865 0.698,2.031 0.177,0.167 10 false *1 2.917,0.573 3.094,0.74 0.177,0.167 10 false *2 1.375,0.406 1.552,0.573 0.177,0.167 10 false *a 2.146,0.073 2.323,0.24 0.177,0.167 10 false *b

Rotate the nut of the transmission control cable approximately 180° in the direction shown in the illustration, and while holding the nut, push in the lock.

Text in Illustration
*1 Nut
*2 Lock
*a Rotate Approximately 180°
*b Push In


b.
C250999E02
2.625,2.125 2.698,2.125 2.698,2.125 2.771,2.344 false 2,0.24 1.865,0.24 1.865,0.24 1.531,0.708 false 0.271,2.302 0.417,2.469 0.146,0.167 10 false A 1.219,2.313 1.365,2.479 0.146,0.167 10 false A 0.698,2.031 0.865,2.198 0.167,0.167 10 false *b 2.438,2.052 2.604,2.219 0.167,0.167 10 false *2 2.021,0.156 2.188,0.323 0.167,0.167 10 false *1 1.031,0.083 1.198,0.25 0.167,0.167 10 false *a

Install the transmission control cable assembly to the shift lever plate.

Text in Illustration
*1 Shift Lever Plate
*2 Lock
*a Install
*b Projecting Part

NOTICE:
·

Install the cable outer with the projecting part facing upwards.

·

After installation, make sure that the cable outer lock is projecting from A as shown in the illustration.

·

Check that the transmission control cable assembly is securely locked.




c.
C249909

Confirm that the shift lever is in N, and then install the cable end to the shift lever assembly.

NOTICE:
·

Securely install the cable end to the shift lever assembly.

·

Install the cable end so that its adjustment lock section is on the driver side.




Hide 3.INSTALL REAR CONSOLE BOX ASSEMBLY

Hide 33504F 4.INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY

a.
C261403

Turn the shift lever knob sub-assembly clockwise to install the shift lever knob sub-assembly.