41336E
1.INSTALL FRONT DRIVE SHAFT DUST COVER
Using a steel plate and a press, install a new front drive shaft dust cover into the front drive inboard joint assembly until it is flush with the end.
| *1 | Steel Plate |
Install the front drive shaft dust cover in the correct direction.
Do not deform the front drive shaft dust cover.
2.INSTALL OUTBOARD JOINT BOOT
Wrap the splines of the front axle outboard joint shaft assembly with protective tape to prevent the boot from being damaged.
| *1 | Protective Tape |
Install new parts onto the front axle outboard joint shaft assembly in the following order:
| *1 | Front Axle Outboard Joint Shaft Assembly |
| *2 | Front No. 2 Axle Outboard Joint Boot Clamp |
| *3 | Outboard Joint Boot |
| *4 | Front Axle Outboard Joint Boot Clamp |
|
Outboard Joint Side |
|
Inboard Joint Side |
Front No. 2 axle outboard joint boot clamp
Outboard joint boot
Front axle outboard joint boot clamp
Pack the joint portion of the front axle outboard joint shaft assembly and outboard joint boot with grease.
116 to 126 g (4.09 to 4.44 oz.)
Install the outboard joint boot onto the front axle outboard joint shaft assembly groove.
Do not allow grease to adhere to the boot clamp track of the outboard joint boot.
Keep the inside of the outboard joint boot free of foreign matter.
43447F
3.INSTALL FRONT NO. 2 AXLE OUTBOARD JOINT BOOT CLAMP
Wear protective gloves. Sharp areas on the parts may injure your hands.
| *a | Fulcrum Point |
| *b | Lever Push Position |
| *c | Band Support Position |
Install the front No. 2 axle outboard joint boot clamp to the outboard joint boot and temporarily fold back the lever at the fulcrum point.
Set the lever to the guide groove correctly and install the clamp as far to the inside of the vehicle as possible.
Check the band and the lever for any deformation before folding back the lever.
The lever folds easily at the fulcrum point when pushed at the position shown in the illustration.
When folding back the lever, do not push at the end of the lever.
| *a | Temporary Claw | - | - |
If the lever bends in the middle, it may not engage with the temporary claws or may not be held in the correct position.
As shown in the illustration, while pressing the outboard joint area against the work surface, firmly press the lever into place by rolling the outboard joint area forward from the folded fulcrum point to the temporary claw area until a click sound is heard.
| *a | Press down | *b | Contact Point |
| *c | Roll forward | *d | Temporary Claw |
| *e | Fulcrum Point | - | - |
Do not damage the deflector.
Make sure that the outboard joint is in direct contact with the work surface.
Using a plastic hammer, tap the buckle to secure it while adjusting the clearance between the lever and the groove to make the clearance between the buckle edge and the lever end even.
Do not damage the outboard joint boot.
43447E
4.INSTALL FRONT AXLE OUTBOARD JOINT BOOT CLAMP
Wear protective gloves. Sharp areas on the parts may injure your hands.
Install the front axle outboard joint boot clamp onto the outboard joint boot and temporarily fold back the lever.
Set the lever into the guide groove correctly.
Check the band and the lever for any deformation before folding back the lever.
Using water pump pliers, pinch the front axle outboard joint boot clamp to temporarily secure it.
| *a | Place the tip near the center of the lever. |
Using a plastic hammer, tap the buckle to secure it while adjusting the clearance between the lever and the groove to make the clearance between the buckle edge and the lever end even.
Do not damage the outboard joint boot.
43474
5.INSTALL DRIVE SHAFT DAMPER (w/ 1 Clamp)
Install the drive shaft damper onto the front axle outboard joint shaft assembly as shown in the illustration.
| *1 | Drive Shaft Damper Setting Clamp |
| *2 | Drive Shaft Damper |
425.6 to 429.6 mm (1.396 to 1.409 ft.)
43474A
6.INSTALL DRIVE SHAFT DAMPER SETTING CLAMP (w/ 1 Clamp)
Secure the front axle outboard joint shaft assembly in a vise using aluminum plates.
Do not overtighten the vise.
for One Touch Type:
Using a screwdriver, install a new drive shaft damper setting clamp as shown in the illustration.
| *A | for One Touch Type |
| *B | for Claw Engagement Type |
| *a | Claws |
for Claw Engagement Type:
Using needle-nose pliers, install a new drive shaft damper setting clamp as shown in the illustration.
43474A
7.INSTALL DRIVE SHAFT DAMPER SETTING CLAMP (w/ 2 Clamps)
Temporarily install the drive shaft damper and 2 new drive shaft damper setting clamps to the front axle outboard joint shaft assembly as shown in the illustration.
| *1 | Drive Shaft Damper Setting Clamp |
| *2 | Drive Shaft Damper |
461.6 to 465.6 mm (1.515 to 1.527 ft.)
43474
8.INSTALL DRIVE SHAFT DAMPER (w/ 2 Clamps)
Secure the front axle outboard joint shaft assembly in a vise using aluminum plates.
Do not overtighten the vise.
Using needle-nose pliers, install the 2 drive shaft damper setting clamps as shown in the illustration.
| *a | Claws |
43040
9.INSTALL FRONT DRIVE INBOARD JOINT ASSEMBLY
Install new parts onto the front axle outboard joint shaft assembly in the following order:
| *1 | Front Axle Inboard Joint Boot Clamp |
| *2 | Inboard Joint Boot |
| *3 | Front No. 2 Axle Inboard Joint Boot Clamp |
| *4 | Protective Tape |
|
Outboard Joint Side |
|
Inboard Joint Side |
Front axle inboard joint boot clamp
Inboard joint boot
Front No. 2 axle inboard joint boot clamp
Secure the front axle outboard joint shaft assembly in a vise using aluminum plates.
Do not overtighten the vise.
Remove the protective tape.
Align the matchmarks and install the tripod joint onto the front axle outboard joint shaft assembly as shown in the illustration.
| *a | Matchmark |
Face the serrated side of the tripod joint outward and install it onto the outboard joint end.
Using a brass bar and a hammer, install the tripod joint to the front axle outboard joint shaft assembly.
Do not tap the rollers.
Keep the tripod joint free of foreign matter.
Using a snap ring expander, install a new shaft snap ring to the front axle outboard joint shaft assembly.
Pack the front drive inboard joint assembly and inboard joint boot with grease.
125 to 135 g (4.40 to 4.76 oz.)
Align the matchmarks and install the front drive inboard joint assembly onto the front axle outboard joint shaft assembly.
| *a | Matchmark |
10.INSTALL INBOARD JOINT BOOT
Install the inboard joint boot to the front drive inboard joint assembly.
Keep the grooves free of grease.
43448F
11.INSTALL FRONT AXLE INBOARD JOINT BOOT CLAMP
Install the front axle inboard joint boot clamp onto the inboard joint boot.
for One Touch Type:
Using a screwdriver, install the front axle inboard joint boot clamp.
Be sure to install the front axle inboard joint boot clamp in the correct position.
Be careful not to damage the inboard joint boot.
for Claw Engagement Type:
Using needle nose pliers, install the front axle inboard joint boot clamp.
| *a | Claws |
Be careful not to deform the front axle inboard joint boot clamp.
Be careful not to damage the inboard joint boot.
43448G
12.INSTALL FRONT NO. 2 AXLE INBOARD JOINT BOOT CLAMP
Install the boot clamp onto the inboard joint boot.
Adjust dimension (A) until it is within the specified length.
| LH Side | RH Side |
|---|---|
| 562.1 mm (1.84 ft.) | 842.1 mm (2.76 ft.) |
for One Touch Type:
Using a screwdriver, install the front No. 2 axle inboard joint boot clamp.
Be sure to install the front No. 2 axle inboard joint boot clamp in the correct position.
Be careful not to damage the inboard joint boot.
for Claw Engagement Type:
Using needle nose pliers, install the front No. 2 axle inboard joint boot clamp.
| *a | Claws |
Be careful not to deform the front No. 2 axle inboard joint boot clamp.
Be careful not to damage the inboard joint boot.
43420
13.INSPECT FRONT DRIVE SHAFT ASSEMBLY