If the wheel alignment has been adjusted, or if suspension or underbody components have been removed/installed or replaced, be sure to perform the following initialization procedure in order for the system to function normally:
Perform zero point calibration of the yaw rate and acceleration sensor.
1. PRECAUTION
Standard values indicated by *1 and *2 in the specification tables are for the vehicles with a purple or blue identification mark on the bottom of the rear coil spring.
| *a | Colored identification mark on the bottom of the rear coil spring |
2.INSPECT TIRES
3.MEASURE VEHICLE HEIGHT
Before inspecting the wheel alignment, adjust the vehicle height to the specified value.
Be sure to perform measurement on a level surface.
If it is necessary to go under the vehicle for measurement, confirm that the parking brake is applied and the vehicle is secured with chocks.
Inspect while the vehicle is unloaded.
The standard value shown here is a value that is used for adjusting the wheel alignment and does not indicate the height of an actual vehicle.
Bounce the vehicle up and down at the corners to stabilize the suspension.
Measure the vehicle height.
A: Ground clearance of front lower No. 1 suspension arm bushing set bolt center
B: Ground clearance of rear axle beam bushing set bolt center
C: Ground clearance of front wheel center
D: Ground clearance of rear wheel center
| Tire Size | Front C - A | Rear D - B |
|---|---|---|
| 175/65R15 | 92 mm (3.62 in.) | 29 mm (1.14 in.) |
| 185/60R15 | 93 mm (3.66 in.)
79 mm (3.11 in.) *1 69 mm (2.72 in.) *2 |
32 mm (1.26 in.)
14 mm (0.55 in.) *1 4 mm (0.16 in.) *2 |
| 195/50R16 | 93 mm (3.66 in.) | 30 mm (1.18 in.) |
*1: Vehicles with purple identification mark on the bottom of the rear coil spring
*2: Vehicles with blue identification mark on the bottom of the rear coil spring
4.INSPECT CAMBER, CASTER AND STEERING AXIS INCLINATION
Inspect while the vehicle is unloaded.
Install a camber-caster-kingpin gauge and place the front wheels on the center of a turning radius gauge.
| *1 | Turning Radius Gauge |
| *2 | Camber-caster-kingpin Gauge |
Inspect the camber, caster and steering axis inclination.
| Tire Size | Camber Inclination | Right-left Difference |
|---|---|---|
| 185/60R15 | -0°13' +/- 0°45' (-0.22° +/- 0.75°)
-0°04' +/- 0°45' (-0.07° +/- 0.75°) *1 0°05' +/- 0°45' (0.08° +/- 0.75°) *2 |
0°30' (0.50°) or less |
| 175/65R15
195/50R16 |
-0°13' +/- 0°45' (-0.22° +/- 0.75°) |
*1: Vehicles with purple identification mark on the bottom of the rear coil spring
*2: Vehicles with blue identification mark on the bottom of the rear coil spring
| Tire Size | Caster Inclination | Right-left Difference |
|---|---|---|
| 175/65R15 | 4°54' +/- 0°45' (4.90° +/- 0.75°) | 0°30' (0.50°) or less |
| 185/60R15 | 4°59' +/- 0°45' (4.98° +/- 0.75°)
4°41' +/- 0°45' (4.68° +/- 0.75°)*1 4°32' +/- 0°45' (4.53° +/- 0.75°) *2 |
|
| 195/50R16 | 4°57' +/- 0°45' (4.95° +/- 0.75°) |
*1: Vehicles with purple identification mark on the bottom of the rear coil spring
*2: Vehicles with blue identification mark on the bottom of the rear coil spring
| Tire Size | Steering Axis Inclination Reference |
|---|---|
| 175/65R15 | 11°23' (11.38°) |
| 185/60R15 | 11°25' (11.42°)
11°04' (11.07°) *1 10°49' (10.82°) *2 |
| 195/50R16 | 11°25' (11.42°) |
*1: Vehicles with purple identification mark on the bottom of the rear coil spring
*2: Vehicles with blue identification mark on the bottom of the rear coil spring
5.ADJUST CAMBER
Inspect toe-in after the camber has been adjusted.
Remove the front wheel.
Remove the 2 nuts on the lower side of the front shock absorber assembly.
Keep the bolts inserted.
Remove the top and bottom bolts one at a time and confirm that the steering knuckle can move freely in the front shock absorber assembly.
Reinstall each bolt after removing it and confirming steering knuckle movement.
If the steering knuckle does not move freely in the front shock absorber assembly, clean the installation surfaces of the front shock absorber assembly and the steering knuckle.
Temporarily install the 2 nuts. (Step A)
Fully push or pull the front axle hub in the direction of the required adjustment. (Step B)
Tighten the nuts.
Keep the bolts from rotating when tightening the nuts.
Install the front wheel.
Check the camber.
If the measured value is not within the specification, calculate the required adjustment amount using the formula below.
Camber adjustment amount = center of the specified range - measured value
Check the combination of the installed bolts. Select appropriate bolts from the tables below to adjust the camber to the specified values.
Try to adjust the camber to the center of the specified values.
| To move the axle hub toward (+) in step B | To move the axle hub toward (-) in step B |
|---|---|
| Refer to table (1) (To move the axle hub toward the positive side) | Refer to table (2) (To move the axle hub toward the negative side) |
The body and suspension may be damaged if the camber cannot be correctly adjusted according to the table above.
Replace the nut with a new one when replacing the bolt.
Table (1) (To move the axle hub toward the positive side)
| *A | Table (1) (To move the axle hub toward the positive side) | *B | Selected Bolt Combination |
| *a | Installed Bolt | *b | Adjusting Value |
| *c | 90109-15001 | *d | 90109-15002 |
| *e | 90109-15003 | *f | 90109-15004 |
Table (2) (To move the axle hub toward the negative side)
| *A | Table (2) (To move the axle hub toward the negative side) | *B | Selected Bolt Combination |
| *a | Installed Bolt | *b | Adjusting Value |
| *c | 90109-15001 | *d | 90109-15002 |
| *e | 90109-15003 | *f | 90109-15004 |
If the camber was out of adjustment in the previous step, perform the adjust camber steps mentioned above. In step (A), replace the existing bolts with the selected bolts.
Replace one bolt at a time when replacing both bolts.
6.INSPECT TOE-IN
Inspect while the vehicle is unloaded.
Bounce the vehicle up and down at the corners to stabilize the suspension.
Release the parking brake and move the shift lever to N.
Push the vehicle straight ahead approximately 5 m (16.4 ft.). (Step C)
Put tread center marks on the rearmost points of the front wheels and measure the distance between the marks (dimension B).
| *a | Tread Center Mark |
| *b | Dimension B |
|
Front of the Vehicle |
Slowly push the vehicle straight ahead to cause the front wheels to rotate 180°. Use the front tire valve as a reference point.
Do not allow the wheels to rotate more than 180°. If the wheels rotate more than 180°, perform the procedure from Step C again.
Measure the distance between the tread center marks on the front of the wheels (dimension A).
| *a | Dimension A |
|
Front of the Vehicle |
| Tire Size | Specified Condition |
|---|---|
| 175/65R15 | C + D: 0°06' +/- 0°12' (0.10° +/- 0.21°) |
| B - A: 1.0 +/- 2.0 mm (0.0394 +/- 0.0787 in.) | |
| 185/60R15 | C + D: 0°06' +/- 0°12' (0.09° +/- 0.19°) |
| B - A: 1.0 +/- 2.0 mm (0.0394 +/- 0.0787 in.) | |
| 195/50R16 | C + D: 0°06' +/- 0°11' (0.09° +/- 0.19°) |
| B - A: 1.0 +/- 2.0 mm (0.0394 +/- 0.0787 in.) |
Measure "B - A" only when "C + D" cannot be measured.
If the toe-in is not within the specified range, adjust it at the rack ends.
7.ADJUST TOE-IN
Make sure that the thread length of the right and left rack ends are approximately the same.
| *a | Thread Length |
1.5 mm (0.0591 in.) or less
Remove the boot clips.
Loosen the tie rod end lock nuts.
Adjust the rack ends if the difference in thread length between the right and left rack ends is not within the specified range.
Extend the shorter rack end if the measured toe-in deviates toward the outer-side.
Shorten the longer rack end if the measured toe-in deviates toward the inner-side.
Turn the right and left rack ends by an equal amount to adjust the toe-in.
Make sure that the thread lengths of the right and left rack ends are the same.
Tighten the tie rod end lock nuts.
Place the boots on the seats and install the clips.
Make sure that the boots are not twisted.
8.INSPECT WHEEL ANGLE
Put tread center marks on the rearmost points of a turning radius gauge.
| *a | Inside |
| *b | Outside |
|
Front of the Vehicle |
Turn the steering wheel fully to the left and right and measure the turning angle.
Inspect while the vehicle is unloaded.
| Tire Size | Inside Wheel | Outside Wheel Reference |
|---|---|---|
| 175/65R15 | 40°50' +/- 2° (40.83° +/- 2°) | 35°11' (35.18°) |
| 185/60R15 | 40°50' +/- 2° (40.83° +/- 2°)
41°09' +/- 2° (41.15° +/- 2°) *1 41°21' +/- 2° (41.35° +/- 2°) *2 |
35°09' (35.15°)
35°30' (35.50°) *1 35°44' (35.73°) *2 |
| 195/50R16 | 32°37' +/- 2° (32.62° +/- 2°) | 29°35' (29.58°) |
*1: Vehicles with purple identification mark on the bottom of the rear coil spring
*2: Vehicles with blue identification mark on the bottom of the rear coil spring
If the right and left inside wheel angles differ from the specified value, check and adjust the right and left rack end lengths.
9.PLACE FRONT WHEELS FACING STRAIGHT AHEAD
10.PERFORM YAW RATE AND ACCELERATION SENSOR CALIBRATION