Home › Suspension › ALIGNMENT / HANDLING DIAGNOSIS › FRONT WHEEL ALIGNMENT › 2013.12–2014.12
RM2170E _53 Suspension _057016 ALIGNMENT / HANDLING DIAGNOSIS _0278004 FRONT WHEEL ALIGNMENT N

ALIGNMENT / HANDLING DIAGNOSIS  FRONT WHEEL ALIGNMENT  ADJUSTMENT  


CAUTION / NOTICE / HINT

NOTICE:

If the wheel alignment has been adjusted, or if suspension or underbody components have been removed/installed or replaced, be sure to perform the following initialization procedure in order for the system to function normally:

Perform zero point calibration of the yaw rate and acceleration sensor.



PROCEDURE

Hide 1. PRECAUTION

Standard values indicated by *1 and *2 in the specification tables are for the vehicles with a purple or blue identification mark on the bottom of the rear coil spring.

C253259E02
2.094,1.698 2.875,1.698 true 2.917,1.604 3.083,1.781 0.167,0.177 10 false *a

Text in Illustration
*a Colored identification mark on the bottom of the rear coil spring

Hide 3.MEASURE VEHICLE HEIGHT

NOTICE:
·

Before inspecting the wheel alignment, adjust the vehicle height to the specified value.

·

Be sure to perform measurement on a level surface.

·

If it is necessary to go under the vehicle for measurement, confirm that the parking brake is applied and the vehicle is secured with chocks.

·

Inspect while the vehicle is unloaded.

·

The standard value shown here is a value that is used for adjusting the wheel alignment and does not indicate the height of an actual vehicle.



a.

Bounce the vehicle up and down at the corners to stabilize the suspension.


b.
C249970E01
0.19,3.754 0.320,3.896 0.130,0.142 10 C 1.459,3.825 1.583,3.967 0.124,0.142 10 A 1.825,3.788 1.943,3.930 0.118,0.142 10 B 3.219,3.757 3.341,3.899 0.122,0.142 10 D

Measure the vehicle height.

Measurement points:

A: Ground clearance of front lower No. 1 suspension arm bushing set bolt center


B: Ground clearance of rear axle beam bushing set bolt center


C: Ground clearance of front wheel center


D: Ground clearance of rear wheel center


Vehicle Height (Unloaded Vehicle):
Tire Size Front C - A Rear D - B
175/65R15 92 mm (3.62 in.) 29 mm (1.14 in.)
185/60R15 93 mm (3.66 in.)
79 mm (3.11 in.) *1
69 mm (2.72 in.) *2
32 mm (1.26 in.)
14 mm (0.55 in.) *1
4 mm (0.16 in.) *2
195/50R16 93 mm (3.66 in.) 30 mm (1.18 in.)


HINT:
·

*1: Vehicles with purple identification mark on the bottom of the rear coil spring

·

*2: Vehicles with blue identification mark on the bottom of the rear coil spring




Hide 4.INSPECT CAMBER, CASTER AND STEERING AXIS INCLINATION

NOTICE:

Inspect while the vehicle is unloaded.


a.
C132440E33
2.385,1.083 2.49,0.802 2.49,0.802 2.719,0.802 false 0.604,0.688 1.031,0.688 1.031,0.688 1.031,1.458 false 2.75,0.729 2.938,0.896 0.188,0.167 10 false *2 0.385,0.594 0.573,0.75 0.188,0.156 10 false *1

Install a camber-caster-kingpin gauge and place the front wheels on the center of a turning radius gauge.

Text in Illustration
*1 Turning Radius Gauge
*2 Camber-caster-kingpin Gauge


b.

Inspect the camber, caster and steering axis inclination.

Camber (Unloaded Vehicle):
Tire Size Camber Inclination Right-left Difference
185/60R15 -0°13' +/- 0°45' (-0.22° +/- 0.75°)
-0°04' +/- 0°45' (-0.07° +/- 0.75°) *1
0°05' +/- 0°45' (0.08° +/- 0.75°) *2
0°30' (0.50°) or less
175/65R15
195/50R16
-0°13' +/- 0°45' (-0.22° +/- 0.75°)


HINT:
·

*1: Vehicles with purple identification mark on the bottom of the rear coil spring

·

*2: Vehicles with blue identification mark on the bottom of the rear coil spring



Caster (Unloaded Vehicle):
Tire Size Caster Inclination Right-left Difference
175/65R15 4°54' +/- 0°45' (4.90° +/- 0.75°) 0°30' (0.50°) or less
185/60R15 4°59' +/- 0°45' (4.98° +/- 0.75°)
4°41' +/- 0°45' (4.68° +/- 0.75°)*1
4°32' +/- 0°45' (4.53° +/- 0.75°) *2
195/50R16 4°57' +/- 0°45' (4.95° +/- 0.75°)


HINT:
·

*1: Vehicles with purple identification mark on the bottom of the rear coil spring

·

*2: Vehicles with blue identification mark on the bottom of the rear coil spring



Steering Axis (Unloaded Vehicle):
Tire Size Steering Axis Inclination Reference
175/65R15 11°23' (11.38°)
185/60R15 11°25' (11.42°)
11°04' (11.07°) *1
10°49' (10.82°) *2
195/50R16 11°25' (11.42°)


HINT:
·

*1: Vehicles with purple identification mark on the bottom of the rear coil spring

·

*2: Vehicles with blue identification mark on the bottom of the rear coil spring




Hide 5.ADJUST CAMBER

NOTICE:

Inspect toe-in after the camber has been adjusted.


a.

Remove the front wheel.


b.
C249872

Remove the 2 nuts on the lower side of the front shock absorber assembly.

NOTICE:

Keep the bolts inserted.



c.

Remove the top and bottom bolts one at a time and confirm that the steering knuckle can move freely in the front shock absorber assembly.

HINT:
·

Reinstall each bolt after removing it and confirming steering knuckle movement.

·

If the steering knuckle does not move freely in the front shock absorber assembly, clean the installation surfaces of the front shock absorber assembly and the steering knuckle.




d.

Temporarily install the 2 nuts. (Step A)


e.
C131799

Fully push or pull the front axle hub in the direction of the required adjustment. (Step B)


f.
C249872

Tighten the nuts.

Torque:
164 N*m (1672 kgf*cm, 121 ft.*lbf)

NOTICE:

Keep the bolts from rotating when tightening the nuts.



g.

Install the front wheel.

Torque:
103 N*m (1050 kgf*cm, 76 ft.*lbf)


h.
C253266E01
0.331,1.081 0.426,1.222 0.095,0.142 10 1 0.329,1.29 0.425,1.431 0.095,0.142 10 2 0.445,1.158 0.657,1.158 false 0.436,1.379 0.648,1.379 false

Check the camber.

If the measured value is not within the specification, calculate the required adjustment amount using the formula below.

Camber adjustment amount = center of the specified range - measured value

Check the combination of the installed bolts. Select appropriate bolts from the tables below to adjust the camber to the specified values.

HINT:

Try to adjust the camber to the center of the specified values.


To move the axle hub toward (+) in step B To move the axle hub toward (-) in step B
Refer to table (1) (To move the axle hub toward the positive side) Refer to table (2) (To move the axle hub toward the negative side)

The body and suspension may be damaged if the camber cannot be correctly adjusted according to the table above.

NOTICE:

Replace the nut with a new one when replacing the bolt.


i.

Table (1) (To move the axle hub toward the positive side)

C212217E12
2.052,0.531 2.188,0.74 0.135,0.208 10 false 1 2.052,1.146 2.188,1.354 0.135,0.208 10 false 2 2.542,0.781 2.719,0.948 0.177,0.167 10 false *c 3.229,1.365 3.417,1.542 0.188,0.177 10 false *d 5.979,0.771 6.125,0.927 0.146,0.156 10 false *e 5.271,0.771 5.469,0.958 0.198,0.188 10 false *d 4.604,1.375 4.781,1.552 0.177,0.177 10 false *f 3.917,1.375 4.094,1.552 0.177,0.177 10 false *e 4.406,6.365 4.552,6.521 0.146,0.156 10 false *f 5.979,1.375 6.188,1.531 0.208,0.156 10 false *f 5.271,1.375 5.469,1.552 0.198,0.177 10 false *f 6.656,1.365 6.833,1.521 0.177,0.156 10 false *f 6.656,0.781 6.823,0.948 0.167,0.167 10 false *f 2.542,3.031 2.677,3.24 0.135,0.208 10 false A 2.542,4.229 2.677,4.438 0.135,0.208 10 false F 2.542,3.51 2.677,3.719 0.135,0.208 10 false C 2.542,3.99 2.677,4.198 0.135,0.208 10 false E 2.542,3.271 2.677,3.479 0.135,0.208 10 false B 2.542,3.75 2.677,3.958 0.135,0.208 10 false D 3.927,3.031 4.063,3.24 0.135,0.208 10 false C 5.271,3.031 5.406,3.24 0.135,0.208 10 false E 3.229,3.031 3.365,3.24 0.135,0.208 10 false B 4.604,3.031 4.74,3.24 0.135,0.208 10 false D 3.229,2.792 3.365,3 0.135,0.208 10 false G 3.229,3.271 3.365,3.479 0.135,0.208 10 false C 3.229,3.75 3.365,3.958 0.135,0.208 10 false E 3.229,3.51 3.365,3.719 0.135,0.208 10 false D 3.229,3.99 3.375,4.198 0.146,0.208 10 false F 3.927,2.552 4.063,2.76 0.135,0.208 10 false G 3.927,2.792 4.063,3 0.135,0.208 10 false A 3.927,3.75 4.063,3.958 0.135,0.208 10 false F 3.927,3.51 4.063,3.719 0.135,0.208 10 false E 3.927,3.271 4.063,3.479 0.135,0.208 10 false D 4.604,2.323 4.74,2.531 0.135,0.208 10 false G 6.656,1.594 6.792,1.802 0.135,0.208 10 false G 5.979,1.833 6.115,2.042 0.135,0.208 10 false G 5.271,2.073 5.406,2.281 0.135,0.208 10 false G 6.656,1.844 6.792,2.052 0.135,0.208 10 false A 6.656,2.313 6.792,2.521 0.135,0.208 10 false C 6.656,2.792 6.792,3 0.135,0.208 10 false E 6.656,2.083 6.792,2.292 0.135,0.208 10 false B 6.656,2.552 6.792,2.76 0.135,0.208 10 false D 5.979,2.083 6.115,2.292 0.135,0.208 10 false A 5.979,2.563 6.115,2.771 0.135,0.208 10 false C 5.979,2.323 6.115,2.531 0.135,0.208 10 false B 5.979,2.792 6.115,3 0.135,0.208 10 false D 5.979,3.031 6.115,3.24 0.135,0.208 10 false F 5.271,3.271 5.406,3.479 0.135,0.208 10 false F 5.271,2.323 5.406,2.531 0.135,0.208 10 false A 5.271,2.792 5.406,3 0.135,0.208 10 false C 5.271,2.563 5.406,2.771 0.135,0.208 10 false B 4.604,2.563 4.74,2.771 0.135,0.208 10 false A 4.604,2.792 4.74,3 0.135,0.208 10 false B 4.604,3.271 4.74,3.479 0.135,0.208 10 false E 4.604,3.51 4.74,3.719 0.135,0.208 10 false F 1.635,5.083 1.771,5.292 0.135,0.208 10 false A 5.094,5.083 5.229,5.292 0.135,0.208 10 false F 3.052,5.083 3.188,5.292 0.135,0.208 10 false C 4.406,5.083 4.542,5.292 0.135,0.208 10 false E 2.344,5.083 2.479,5.292 0.135,0.208 10 false B 3.729,5.083 3.865,5.292 0.135,0.208 10 false D 5.802,5.083 5.938,5.292 0.135,0.208 10 false G 1.073,5.5 1.208,5.708 0.135,0.208 10 false 1 1.104,6.135 1.24,6.344 0.135,0.208 10 false 2 3.052,6.365 3.229,6.521 0.177,0.156 10 false *f 3.729,6.365 3.969,6.531 0.24,0.167 10 false *f 5.094,6.365 5.302,6.563 0.208,0.198 10 false *f 5.094,5.74 5.281,5.896 0.188,0.156 10 false *f 4.406,5.74 4.604,5.896 0.198,0.156 10 false *e 2.344,6.365 2.552,6.531 0.208,0.167 10 false *e 1.635,6.365 1.781,6.521 0.146,0.156 10 false *d 3.729,5.74 3.917,5.927 0.188,0.188 10 false *d 3.052,5.74 3.25,5.927 0.198,0.188 10 false *c 1.635,5.74 1.813,5.927 0.177,0.188 10 false *c 2.344,5.74 2.521,5.896 0.177,0.156 10 false *c 5.802,6.365 5.99,6.531 0.188,0.167 10 false *c 5.802,5.74 6.01,5.927 0.208,0.188 10 false *c 0.177,1.604 2.198,1.792 2.021,0.188 10 false -1°30' to -1°15' (-1.50° to -1.25°) 0.406,2.802 1.969,2.99 1.563,0.188 10 false -0°15' to 0° (-0.25° to 0°) 0.208,2.563 2.156,2.781 1.948,0.219 10 false -0°30' to -0°15' (-0.5° to -0.25°) 0.208,2.323 2.156,2.521 1.948,0.198 10 false -0°45' to -0°30' (-0.75° to -0.5°) 0.271,2.083 2.104,2.26 1.833,0.177 10 false -1°00' to -0°45' (-1° to -0.75°) 0.26,1.844 2.094,2.052 1.833,0.208 10 false -1°15' to -1°00' (-1.25° to -1°) 0.354,3.99 2.01,4.167 1.656,0.177 10 false 1°00' to 1°15' (1° to 1.25°) 0.354,3.75 2,3.948 1.646,0.198 10 false 0°45' to 1°00' (0.75° to 1°) 0.302,3.51 2.063,3.688 1.76,0.177 10 false 0°30' to 0°45' (0.5° to 0.75°) 0.302,3.271 2.073,3.448 1.771,0.177 10 false 0°15' to 0°30' (0.25° to 0.5°) 0.448,3.031 1.917,3.229 1.469,0.198 10 false 0° to 0°15' (0° to 0.25°) 0.302,4.229 2.073,4.406 1.771,0.177 10 false 1°15' to 1°30' (1.25° to 1.5°) 2.542,1.365 2.719,1.542 0.177,0.177 10 false *c 3.229,0.781 3.406,0.938 0.177,0.156 10 false *c 3.927,0.781 4.115,0.969 0.188,0.188 10 false *c 4.604,0.781 4.781,0.948 0.177,0.167 10 false *c 1.156,0.625 1.333,0.792 0.177,0.167 10 false *a 0.625,1.115 0.802,1.281 0.177,0.167 10 false *b 0.875,4.792 1.052,4.958 0.177,0.167 10 false *B 0.063,0.135 0.26,0.302 0.198,0.167 10 false *A

Text in Illustration
*A Table (1) (To move the axle hub toward the positive side) *B Selected Bolt Combination
*a Installed Bolt *b Adjusting Value
*c 90109-15001 *d 90109-15002
*e 90109-15003 *f 90109-15004


ii.

Table (2) (To move the axle hub toward the negative side)

C212218E12
2.052,0.531 2.188,0.74 0.135,0.208 10 false 1 2.052,1.146 2.188,1.354 0.135,0.208 10 false 2 1.635,5.083 1.771,5.292 0.135,0.208 10 false A 5.094,5.083 5.229,5.292 0.135,0.208 10 false F 3.052,5.083 3.188,5.292 0.135,0.208 10 false C 4.406,5.083 4.542,5.292 0.135,0.208 10 false E 2.344,5.083 2.479,5.292 0.135,0.208 10 false B 3.729,5.083 3.865,5.292 0.135,0.208 10 false D 5.802,5.083 5.938,5.292 0.135,0.208 10 false G 1.073,5.5 1.208,5.708 0.135,0.208 10 false 1 1.104,6.135 1.24,6.344 0.135,0.208 10 false 2 0.177,1.615 2.198,1.802 2.021,0.188 10 false -1°30' to -1°15' (-1.50° to -1.25°) 0.406,2.792 1.969,2.979 1.563,0.188 10 false -0°15' to 0° (-0.25° to 0°) 0.208,2.552 2.156,2.771 1.948,0.219 10 false -0°30' to -0°15' (-0.5° to -0.25°) 0.208,2.323 2.156,2.521 1.948,0.198 10 false -0°45' to -0°30' (-0.75° to -0.5°) 0.271,2.083 2.104,2.26 1.833,0.177 10 false -1°00' to -0°45' (-1° to -0.75°) 0.26,1.844 2.094,2.052 1.833,0.208 10 false -1°15' to -1°00' (-1.25° to -1°) 0.354,3.99 2.01,4.167 1.656,0.177 10 false 1°00' to 1°15' (1° to 1.25°) 0.354,3.74 2,3.938 1.646,0.198 10 false 0°45' to 1°00' (0.75° to 1°) 0.302,3.5 2.063,3.677 1.76,0.177 10 false 0°30' to 0°45' (0.5° to 0.75°) 0.302,3.271 2.073,3.448 1.771,0.177 10 false 0°15' to 0°30' (0.25° to 0.5°) 0.448,3.031 1.917,3.229 1.469,0.198 10 false 0° to 0°15' (0° to 0.25°) 0.302,4.219 2.073,4.396 1.771,0.177 10 false 1°15' to 1°30' (1.25° to 1.5°) 1.156,0.625 1.333,0.792 0.177,0.167 10 false *a 0.625,1.115 0.802,1.281 0.177,0.167 10 false *b 0.875,4.792 1.052,4.958 0.177,0.167 10 false *B 0.063,0.135 0.26,0.302 0.198,0.167 10 false *A 5.292,2.802 5.427,3.01 0.135,0.208 10 false E 5.292,3.76 5.427,3.969 0.135,0.208 10 false G 5.292,2.563 5.427,2.771 0.135,0.208 10 false F 5.292,3.521 5.427,3.729 0.135,0.208 10 false A 5.292,3.031 5.427,3.24 0.135,0.208 10 false C 5.292,3.271 5.427,3.479 0.135,0.208 10 false B 2.542,2.802 2.677,3.01 0.135,0.208 10 false A 2.542,1.615 2.677,1.823 0.135,0.208 10 false F 2.542,2.323 2.677,2.531 0.135,0.208 10 false C 2.542,1.844 2.677,2.052 0.135,0.208 10 false E 2.552,2.563 2.688,2.771 0.135,0.208 10 false B 2.542,2.094 2.677,2.302 0.135,0.208 10 false D 3.229,2.802 3.365,3.01 0.135,0.208 10 false B 3.229,3.031 3.365,3.24 0.135,0.208 10 false G 3.229,2.563 3.365,2.771 0.135,0.208 10 false C 3.229,2.094 3.365,2.302 0.135,0.208 10 false E 3.229,2.323 3.365,2.531 0.135,0.208 10 false D 3.229,1.844 3.375,2.052 0.146,0.208 10 false F 3.927,2.802 4.063,3.01 0.135,0.208 10 false C 3.927,3.271 4.063,3.479 0.135,0.208 10 false G 3.927,3.031 4.063,3.24 0.135,0.208 10 false A 3.927,2.094 4.063,2.302 0.135,0.208 10 false F 3.927,2.323 4.063,2.531 0.135,0.208 10 false E 3.927,2.563 4.063,2.771 0.135,0.208 10 false D 4.604,2.802 4.74,3.01 0.135,0.208 10 false D 4.604,3.521 4.74,3.729 0.135,0.208 10 false G 4.604,3.281 4.74,3.49 0.135,0.208 10 false A 4.604,3.031 4.74,3.24 0.135,0.208 10 false B 4.604,2.563 4.74,2.771 0.135,0.208 10 false E 4.604,2.323 4.74,2.531 0.135,0.208 10 false F 5.99,3.99 6.125,4.198 0.135,0.208 10 false G 5.99,3.75 6.125,3.958 0.135,0.208 10 false A 5.99,3.271 6.125,3.479 0.135,0.208 10 false C 5.99,3.521 6.125,3.729 0.135,0.208 10 false B 5.99,3.031 6.125,3.24 0.135,0.208 10 false D 5.99,2.802 6.125,3.01 0.135,0.208 10 false F 6.688,4.229 6.823,4.438 0.135,0.208 10 false G 6.688,3.99 6.823,4.198 0.135,0.208 10 false A 6.688,3.521 6.823,3.729 0.135,0.208 10 false C 6.688,3.031 6.823,3.24 0.135,0.208 10 false E 6.688,3.75 6.823,3.958 0.135,0.208 10 false B 6.688,3.271 6.823,3.479 0.135,0.208 10 false D 2.542,0.781 2.719,0.948 0.177,0.167 10 false *c 3.229,1.375 3.417,1.552 0.188,0.177 10 false *d 5.979,0.781 6.125,0.938 0.146,0.156 10 false *e 5.271,0.781 5.469,0.969 0.198,0.188 10 false *d 4.604,1.375 4.781,1.552 0.177,0.177 10 false *f 3.927,1.375 4.104,1.552 0.177,0.177 10 false *e 5.979,1.375 6.188,1.531 0.208,0.156 10 false *f 5.271,1.375 5.469,1.552 0.198,0.177 10 false *f 6.656,1.375 6.833,1.531 0.177,0.156 10 false *f 6.656,0.781 6.823,0.948 0.167,0.167 10 false *f 2.542,1.375 2.719,1.552 0.177,0.177 10 false *c 3.229,0.781 3.406,0.938 0.177,0.156 10 false *c 3.927,0.792 4.115,0.979 0.188,0.188 10 false *c 4.604,0.781 4.781,0.948 0.177,0.167 10 false *c 4.406,6.375 4.552,6.531 0.146,0.156 10 false *f 3.052,6.375 3.229,6.531 0.177,0.156 10 false *f 3.729,6.375 3.969,6.542 0.24,0.167 10 false *f 5.094,6.375 5.302,6.573 0.208,0.198 10 false *f 5.094,5.75 5.281,5.906 0.188,0.156 10 false *f 4.406,5.75 4.604,5.906 0.198,0.156 10 false *e 2.344,6.375 2.552,6.542 0.208,0.167 10 false *e 1.635,6.375 1.781,6.531 0.146,0.156 10 false *d 3.729,5.75 3.917,5.938 0.188,0.188 10 false *d 3.052,5.75 3.25,5.938 0.198,0.188 10 false *c 1.635,5.75 1.813,5.938 0.177,0.188 10 false *c 2.344,5.75 2.521,5.906 0.177,0.156 10 false *c 5.802,6.375 5.99,6.542 0.188,0.167 10 false *c 5.802,5.75 6.01,5.938 0.208,0.188 10 false *c

Text in Illustration
*A Table (2) (To move the axle hub toward the negative side) *B Selected Bolt Combination
*a Installed Bolt *b Adjusting Value
*c 90109-15001 *d 90109-15002
*e 90109-15003 *f 90109-15004



i.

If the camber was out of adjustment in the previous step, perform the adjust camber steps mentioned above. In step (A), replace the existing bolts with the selected bolts.

HINT:

Replace one bolt at a time when replacing both bolts.



Hide 6.INSPECT TOE-IN

NOTICE:

Inspect while the vehicle is unloaded.


a.

Bounce the vehicle up and down at the corners to stabilize the suspension.


b.

Release the parking brake and move the shift lever to N.


c.

Push the vehicle straight ahead approximately 5 m (16.4 ft.). (Step C)


d.
C188968E17
0.833,0.583 0.833,1.115 false 1.365,0.583 1.365,0.99 1.365,0.99 0.833,0.99 false 2.521,1.333 2.521,1.667 false 0.74,1.135 0.917,1.302 0.177,0.167 10 false *a 2.427,1.698 2.604,1.854 0.177,0.156 10 false *b

Put tread center marks on the rearmost points of the front wheels and measure the distance between the marks (dimension B).

Text in Illustration
*a Tread Center Mark
*b Dimension B
V100135

Front of the Vehicle


e.

Slowly push the vehicle straight ahead to cause the front wheels to rotate 180°. Use the front tire valve as a reference point.

HINT:

Do not allow the wheels to rotate more than 180°. If the wheels rotate more than 180°, perform the procedure from Step C again.



f.
C188969E17
0.647,1.275 0.647,1.636 false 1.912,0.543 2.051,0.704 0.14,0.16 10 C 3.071,0.55 3.21,0.71 0.14,0.16 10 D 2.498,0.717 2.638,0.877 0.14,0.16 10 A 2.509,1.537 2.649,1.698 0.14,0.16 10 B 0.563,1.655 0.735,1.815 0.172,0.16 10 *a

Measure the distance between the tread center marks on the front of the wheels (dimension A).

Text in Illustration
*a Dimension A
V100135

Front of the Vehicle

Toe-in (Unloaded Vehicle):
Tire Size Specified Condition
175/65R15 C + D: 0°06' +/- 0°12' (0.10° +/- 0.21°)
B - A: 1.0 +/- 2.0 mm (0.0394 +/- 0.0787 in.)
185/60R15 C + D: 0°06' +/- 0°12' (0.09° +/- 0.19°)
B - A: 1.0 +/- 2.0 mm (0.0394 +/- 0.0787 in.)
195/50R16 C + D: 0°06' +/- 0°11' (0.09° +/- 0.19°)
B - A: 1.0 +/- 2.0 mm (0.0394 +/- 0.0787 in.)


HINT:

Measure "B - A" only when "C + D" cannot be measured.


If the toe-in is not within the specified range, adjust it at the rack ends.


Hide 7.ADJUST TOE-IN

a.
C249963E02
2.5,1.188 2.719,1.385 0.219,0.198 10 true *a

Make sure that the thread length of the right and left rack ends are approximately the same.

Text in Illustration
*a Thread Length

Standard difference:

1.5 mm (0.0591 in.) or less



b.

Remove the boot clips.


c.
C249964

Loosen the tie rod end lock nuts.


d.

Adjust the rack ends if the difference in thread length between the right and left rack ends is not within the specified range.

i.

Extend the shorter rack end if the measured toe-in deviates toward the outer-side.


ii.

Shorten the longer rack end if the measured toe-in deviates toward the inner-side.



e.

Turn the right and left rack ends by an equal amount to adjust the toe-in.


f.

Make sure that the thread lengths of the right and left rack ends are the same.


g.

Tighten the tie rod end lock nuts.

Torque:
75 N*m (760 kgf*cm, 55 ft.*lbf)


h.

Place the boots on the seats and install the clips.

HINT:

Make sure that the boots are not twisted.



Hide 8.INSPECT WHEEL ANGLE

a.
C132439E11
0.863,0.204 1.036,0.380 0.173,0.176 10 *b 0.538,0.204 0.713,0.380 0.175,0.176 10 *a 2.397,0.204 2.570,0.380 0.173,0.176 10 *b 2.725,0.204 2.900,0.380 0.175,0.176 10 *a

Put tread center marks on the rearmost points of a turning radius gauge.

Text in Illustration
*a Inside
*b Outside
V100135

Front of the Vehicle


b.

Turn the steering wheel fully to the left and right and measure the turning angle.

NOTICE:

Inspect while the vehicle is unloaded.


Wheel Angle (Unloaded Vehicle):
Tire Size Inside Wheel Outside Wheel Reference
175/65R15 (5J) 40°50' +/- 2° (40.83° +/- 2°) 35°11' (35.18°)
175/65R15 (5.5J) 40°04' +/- 2° (40.07° +/- 2°) 34°41' (34.68°)
185/60R15 40°50' +/- 2° (40.83° +/- 2°)
41°09' +/- 2° (41.15° +/- 2°) *1
41°21' +/- 2° (41.35° +/- 2°) *2
35°09' (35.15°)
35°30' (35.50°) *1
35°44' (35.73°) *2
195/50R16 32°37' +/- 2° (32.62° +/- 2°) 29°35' (29.58°)


HINT:
·

*1: Vehicles with purple identification mark on the bottom of the rear coil spring

·

*2: Vehicles with blue identification mark on the bottom of the rear coil spring



If the right and left inside wheel angles differ from the specified value, check and adjust the right and left rack end lengths.



Hide 9.PLACE FRONT WHEELS FACING STRAIGHT AHEAD

Hide 10.PERFORM YAW RATE AND ACCELERATION SENSOR CALIBRATION