Home › Suspension › REAR SUSPENSION › REAR COIL SPRING › 2011.12–2014.12
RM2170E _53 Suspension _057018 REAR SUSPENSION _0278013 REAR COIL SPRING A

REAR SUSPENSION  REAR COIL SPRING  REMOVAL  


CAUTION / NOTICE / HINT

CAUTION:

Before removing the rear axle beam assembly, make sure to support the front suspension crossmember sub-assembly using a jack or equivalent. If the rear axle beam assembly is removed without the vehicle supported, the front-to-rear weight distribution will become unbalanced and may cause the vehicle to fall off the lift.


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 3.REMOVE REAR WHEELS

Hide 4.DRAIN BRAKE FLUID

NOTICE:

Immediately wash off any brake fluid that comes into contact with any painted surfaces.


Hide 89407A 5.REMOVE REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY (w/ Height Control Sensor)

Hide 89516D 6.DISCONNECT SKID CONTROL SENSOR WIRE LH

Hide 89516C 7.DISCONNECT SKID CONTROL SENSOR WIRE RH

HINT:

Perform the same procedure as the LH side.


Hide 89516D 8.SEPARATE SKID CONTROL SENSOR WIRE LH

a.
C107566

Remove the nut and separate the skid control sensor wire LH.


Hide 89516C 9.SEPARATE SKID CONTROL SENSOR WIRE RH

HINT:

Perform the same procedure as the LH side.


Hide 47319F 10.SEPARATE REAR FLEXIBLE HOSE LH

a.
C235742

Using a union nut wrench, separate the brake tube while holding the rear flexible hose LH with a wrench.

NOTICE:
·

Do not bend or damage the brake line.

·

Do not allow any foreign matter such as dirt and dust to enter the brake line from the connecting points.




b.

Remove the clip and separate the rear flexible hose LH from the rear axle beam assembly.


Hide 47318F 11.SEPARATE REAR FLEXIBLE HOSE RH

HINT:

Perform the same procedure as the LH side.


Hide 42110F 12.LOOSEN REAR AXLE BEAM ASSEMBLY

a.
C249958E01
0.102,0.036 0.292,0.202 0.191,0.166 10 *A 1.855,0.036 2.045,0.202 0.191,0.166 10 *B

Loosen the 2 bolts.

Text in Illustration
*A LH Side
*B RH Side

NOTICE:

Do not remove the 2 bolts.



Hide 48231B 13.REMOVE REAR COIL SPRING LH

a.

Support the spring seat of the rear axle beam assembly using 2 jacks and 2 wooden blocks.

C249968E02
1.24,1.792 0.927,1.792 false 1.094,2.125 1.094,1.979 1.094,1.979 0.938,1.979 false 5.76,1.823 6.021,1.823 false 5.927,2.125 5.927,1.99 5.927,1.99 6.052,1.99 false 0.771,1.708 0.948,1.854 0.177,0.146 10 false *1 0.781,1.885 0.958,2.073 0.177,0.188 10 false *2 6.052,1.74 6.229,1.885 0.177,0.146 10 false *1 6.073,1.917 6.25,2.104 0.177,0.188 10 false *2

Text in Illustration
*1 Wooden Block *2 Jack


b.

Remove the 2 bolts while holding the 2 nuts and separate the rear axle beam assembly from the rear shock absorber assemblies LH and RH.

NOTICE:

Since stopper nuts are used, turn the bolts.



c.

Slowly lower the rear axle beam assembly using 2 jacks and 2 wooden blocks, and remove the rear coil spring LH.


d.

Slowly jack up the rear axle beam assembly using 2 jacks and 2 wooden blocks, and temporarily tighten the rear axle beam assembly to the rear shock absorber assemblies LH and RH with the 2 bolts and 2 nuts.

NOTICE:

Since stopper nuts are used, turn the bolts.



Hide 48231A 14.REMOVE REAR COIL SPRING RH

HINT:

Perform the same procedure as the LH side.


Hide 48259A 15.REMOVE REAR UPPER COIL SPRING INSULATOR LH

Hide 48257C 16.REMOVE REAR UPPER COIL SPRING INSULATOR RH

Hide 48258C 17.REMOVE REAR LOWER COIL SPRING INSULATOR LH

Hide 48258B 18.REMOVE REAR LOWER COIL SPRING INSULATOR RH