Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE BOOSTER(for LHD) › 2011.12–2014.12
RM2170E _54 Brake _057022 BRAKE SYSTEM (OTHER) _0278034 BRAKE BOOSTER(for LHD) A

BRAKE SYSTEM (OTHER)  BRAKE BOOSTER(for LHD)  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 2. DISABLE BRAKE CONTROL

a.

Wait at least 2 minutes after turning the power switch off.

NOTICE:

When the brake pedal is depressed or the door courtesy switch is turned on even if the power switch is off, the brake control system activates. Therefore do not depress the brake pedal or open/close the doors until the reservoir level switch connector is disconnected.



b.
C250008

Disconnect the reservoir level switch connector with the parking brake applied.


c.

Disconnect the cable from the negative (-) auxiliary battery terminal (See page Power Source / Network>1NZ-FXE BATTERY / CHARGING>AUXILIARY BATTERY>REMOVAL).


d.

Depress the brake pedal 40 times or more to return all the fluid in the accumulator back to the reservoir.


e.

Check that the brake pedal can not be further depressed.


f.

Release the parking brake.


Hide 3.REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 55722C 4.REMOVE INNER COWL TOP TO COWL BRACE

a.
C250011

Remove the 3 bolts and inner cowl top to cowl brace.


Hide 55735B 5.REMOVE FRONT AIR SHUTTER SEAL

a.
C250012

Disengage the clamp to remove the front air shutter seal.


Hide 55815E 6.REMOVE FRONT NO. 1 VENTILATOR SEAL

a.
C250013

Disengage the clamp to remove the front No. 1 ventilator seal.


Hide 55701J 7.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY

a.
C250014

Disengage the clamp to separate the wire harness from the outer cowl top panel sub-assembly.


b.
C250015

Remove the 8 bolts, nut and outer cowl top panel sub-assembly.


Hide 8.DRAIN BRAKE FLUID

NOTICE:

If brake fluid leaks onto any painted surface, immediately clean it off.


Hide 47101A 9.REMOVE BRAKE PEDAL RETURN SPRING

Hide 47220D 11.SEPARATE BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY

a.
C250016

Remove the 2 nuts and separate the brake master cylinder reservoir assembly from the reservoir bracket.


Hide 47235G 12.DISCONNECT NO. 2 RESERVOIR HOSE

a.
C250017

Move the clip and disconnect the No. 2 reservoir hose from the brake booster with master cylinder assembly.


Hide 47234L 13.DISCONNECT NO. 1 RESERVOIR HOSE

a.
C250019

Move the clip and disconnect the No. 1 reservoir hose from the brake booster with master cylinder assembly.


Hide 47233 14.REMOVE RESERVOIR BRACKET

a.
C250021

Remove the 2 bolts and reservoir bracket.


Hide 44571 15.DISCONNECT BRAKE ACTUATOR HOSE

a.
C250022

Move the clip and disconnect the brake actuator hose from the brake master cylinder reservoir assembly.


Hide 47220D 16.REMOVE BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY

Hide 47381N 17.REMOVE TUBE CLAMP BRACKET

a.
C250024

Remove the 2 bolts and tube clamp bracket from the brake booster with master cylinder assembly and front No. 1 brake tube.


Hide 47210L 18.REMOVE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

a.
C250026

Release the lock lever and disconnect the connector.

Text in Illustration
V100135

Release the lock lever
V100136

Disconnect the connector

NOTICE:

Be careful not to allow the brake fluid to enter the removed connector.



b.
U159491E03
1.438,1.667 2.76,1.667 true 1.417,1.542 2.479,1.542 true 1.417,1.427 2.229,1.427 true 1.396,1.313 1.979,1.313 true 1.302,1.115 1.135,1.292 1.135,1.292 0.833,1.292 true 2.76,1.573 2.917,1.719 0.156,0.146 10 false *d 2.479,1.448 2.635,1.594 0.156,0.146 10 true *c 2.229,1.333 2.385,1.479 0.156,0.146 10 true *b 1.979,1.219 2.135,1.365 0.156,0.146 10 true *a 0.656,1.188 0.813,1.333 0.156,0.146 10 false *e

Using a union nut wrench, disconnect the 5 brake lines from the brake booster with master cylinder assembly.


c.

Use tags or make a memo to identify the places to reconnect the lines.

Text in Illustration
*a to Front Wheel Cylinder LH
*b to Rear Wheel Cylinder RH
*c to Brake Booster Pump Assembly
*d to Rear Wheel Cylinder LH
*e to Front Wheel Cylinder RH


d.
C250004E01
2.102,2.598 2.268,2.746 0.166,0.149 10 *1 0.382,2.821 0.548,2.969 0.166,0.149 10 *2 2.274,4.223 2.440,4.371 0.166,0.149 10 *5 1.648,2.692 2.102,2.692 false 3.142,2.884 3.308,3.033 0.166,0.149 10 *3 2.83,2.978 3.142,2.978 false 2.79,3.17 2.956,3.318 0.166,0.149 10 *4 2.478,3.264 2.79,3.264 false 1.629,3.323 0.576,2.927 0.576,2.927 1.216,3.551 false 1.711,3.897 2.274,4.303 2.274,4.303 1.503,4.278 false

Remove the 4 nuts and brake booster with master cylinder assembly.

Text in Illustration
*1 Connector Portion
*2 Union
*3 Push Rod Clevis
*4 Boot
*5 Front No. 2 Brake Tube

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not carry the brake booster with master cylinder assembly by the portion shown in bold in the illustration.

·

Be careful not to allow any brake fluid to enter the connector.




Hide 44785C 19.REMOVE BRAKE BOOSTER GASKET