Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM › from 2015.11
RM2170E _53 Suspension _057019 TIRE PRESSURE MONITORING _0278018 TIRE PRESSURE WARNING SYSTEM C

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING SYSTEM  C2198/98  Initialization Switch (for Test Mode DTC)  


DESCRIPTION

During test mode, when the tire pressure warning reset switch is on, the tire pressure warning light illuminates and when the tire pressure warning reset switch is off, the tire pressure warning light blinks at 0.125 second intervals.

DTC No. DTC Detection Condition Trouble Area
C2198/98 Test mode procedure is performed.
·

Tire pressure warning reset switch

·

Wire harness or connector

·

Tire pressure warning ECU and receiver



WIRING DIAGRAM

C270966E30
5.219,2.969 6.594,3.323 1.375,0.354 10 false Tire Pressure Warning ECU and Receiver 1.948,1.521 4.427,1.781 2.479,0.26 10 false Tire Pressure Warning Reset Switch 1.969,1.354 2.333,1.563 0.365,0.208 10 false G82 2.271,0.906 2.375,1.083 0.104,0.177 10 false 2 3.438,0.906 3.542,1.083 0.104,0.177 10 false 1 5.229,2.813 5.552,2.99 0.323,0.177 10 false M48 5.26,0.885 5.375,1.042 0.115,0.156 10 false 3 5.479,1.01 5.917,1.167 0.438,0.156 10 false CLSW 2.479,0.906 2.604,1.083 0.125,0.177 10 false E 3.104,0.906 3.354,1.063 0.25,0.156 10 false INT

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the tire pressure warning ECU and receiver, read the transmitter IDs stored in the old ECU using the GTS and write them down before removal.

·

It is necessary to perform initialization (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION) after registration (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION) of the transmitter IDs into the tire pressure warning ECU and receiver if the ECU has been replaced.



PROCEDURE

1.INSPECT TIRE PRESSURE WARNING RESET SWITCH
a.
C253878E01
0.135,0.079 0.430,0.408 0.295,0.330 10 *a 1.422,1.108 1.668,1.250 0.246,0.142 10 *b 1.826,1.646 2.135,1.788 0.309,0.142 10 *c 2.351,1.605 2.591,1.764 0.240,0.158 10 E 2.914,1.605 3.243,1.764 0.329,0.158 10 INT 2.559,1.228 2.441,1.576 false 2.879,1.228 3.003,1.582 false

Remove the tire pressure warning reset switch.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (INT) - 2 (E) On Below 1 Ω
Off 10 kΩ or higher



Text in Illustration
*a Component without harness connected
(Tire Pressure Warning Reset Switch)
*b On
*c Off


OK

2.CHECK HARNESS AND CONNECTOR (RESET SWITCH - TIRE PRESSURE WARNING ECU AND RECEIVER)

NG

REPLACE TIRE PRESSURE WARNING RESET SWITCH

2.CHECK HARNESS AND CONNECTOR (RESET SWITCH - TIRE PRESSURE WARNING ECU AND RECEIVER)
a.

Disconnect the G82 tire pressure warning reset switch connector.


b.

Disconnect the M48 tire pressure warning ECU and receiver connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M48-3 (CLSW) - G82-1 (INT) Always Below 1 Ω
M48-3 (CLSW) or G82-1 (INT) - Body ground Always 10 kΩ or higher
G82-2 (E) - Body ground Always Below 1 Ω




OK

REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR