Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM › 2011.12–2013.12
RM2170E _54 Brake _057021 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0278020 ELECTRONICALLY CONTROLLED BRAKE SYSTEM U

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  TERMINALS OF ECU  


TERMINALS OF ECU


C156569E02
0.25,0.213 0.489,0.390 0.239,0.177 10 *a

Text in Illustration
*a Component without harness connected
(Skid Control ECU (Brake Booster with Master Cylinder Assembly))
- -

Terminal No. (Symbol) Terminal Description
1 (MRI1) Motor power supply input 1
2 (MRI2) Motor power supply input 2
3 (STP0) Stop light control relay (Stop light switch assembly) output
4 - (Not used)
5 (FR-) Front speed sensor RH (-) signal input
6 (STP2) Stop light control relay (Stop light switch assembly) input
7 (RL-) Rear speed sensor LH (-) signal input
8 - (Not used)
9 (RR-) Rear speed sensor RH (-) signal input
10 - (Not used)
11 (SP1) Speed sensor signal output
12 (IG2) IG2 power source input
13 - (Not used)
14 (BI) +B power source input
15 (BS) Solenoid power supply input
16 (IG1) IG1 power source input
17 - (Not used)
18 (FR+) Front speed sensor RH (+) power supply output
19 (CTY) Front door courtesy light switch assembly input
20 (RL+) Rear speed sensor LH (+) power supply output
21 - (Not used)
22 (RR+) Rear speed sensor RH (+) power supply output
23 (GND6) Skid control ECU (Brake booster with master cylinder assembly) ground 6
24 (GND5) Skid control ECU (Brake booster with master cylinder assembly) ground 5
25 (GND4) Skid control ECU (Brake booster with master cylinder assembly) ground 4
26 (GND3) Skid control ECU (Brake booster with master cylinder assembly) ground 3
27 (GND2) Skid control ECU (Brake booster with master cylinder assembly) ground 2
28 (GND) Skid control ECU (Brake booster with master cylinder assembly) ground
29 (MRO1) Motor power supply output 1
30 (MRO2) Motor power supply output 2
31 (FL+) Front speed sensor LH (+) power supply output
32 (FL-) Front speed sensor LH (-) signal input
33 (STP) Stop light switch assembly input
34 (CA2L) CAN communication line 2 (L)
35 (CA2H) CAN communication line 2 (H)
36 (LBL) Brake fluid level warning switch input
37 (CA1H) CAN communication line 1 (H)
38 (CA1L) CAN communication line 1 (L)
39 (VCSK) Brake pedal stroke sensor assembly power supply output
40 (SKS2) Brake pedal stroke sensor assembly signal input 2
41 (SKG) Brake pedal stroke sensor assembly ground
42 (SKS) Brake pedal stroke sensor assembly signal input


TERMINAL INSPECTION


a.

Disconnect the connector and measure the voltage or resistance on the wire harness side.

U183506E02
0.302,0.208 0.479,0.365 0.177,0.156 10 false *a 1.573,1.563 1.844,1.708 0.271,0.146 10 false A41

Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU (Brake Booster with Master Cylinder Assembly))
- -

HINT:

The voltage cannot be measured with the connector connected to the skid control ECU (brake booster with master cylinder assembly) as the connector is watertight.


Standard
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A41-1 (MRI1) - Body ground B - Body ground Motor power supply input 1 Always 11 to 14 V
A41-2 (MRI2) - Body ground R - Body ground Motor power supply input 2 Always 11 to 14 V
A41-3 (STP0) - Body ground Y - Body ground Stop light control relay (Stop light switch assembly) output Power switch on (IG) 11 to 14 V
A41-6 (STP2) - Body ground L - Body ground Stop light control relay (Stop light switch assembly) input Stop light switch assembly ON → OFF
(Brake pedal depressed → released)
11 to 14 V → Below 1.5 V
A41-12 (IG2) - Body ground BE - Body ground IG2 power source input Power switch on (IG) 11 to 14 V
A41-14 (BI) - Body ground W - Body ground +B power source input Always 11 to 14 V
A41-15 (BS) - Body ground B - Body ground Solenoid power supply input Always 11 to 14 V
A41-16 (IG1) - Body ground B - Body ground IG1 power source input Power switch on (IG) 11 to 14 V
A41-19 (CTY) - Body ground V - Body ground Front door courtesy light switch assembly input Driver door closed → open 11 to 14 V → Below 1.5 V
A41-23 (GND6) - Body ground W-B - Body ground Skid control ECU (Brake booster with master cylinder assembly) ground 6 1 minute or more after disconnecting the cable from the negative (-) auxiliary battery terminal Below 1 Ω
A41-24 (GND5) - Body ground W-B - Body ground Skid control ECU (Brake booster with master cylinder assembly) ground 5 1 minute or more after disconnecting the cable from the negative (-) auxiliary battery terminal Below 1 Ω
A41-25 (GND4) - Body ground W-B - Body ground Skid control ECU (Brake booster with master cylinder assembly) ground 4 1 minute or more after disconnecting the cable from the negative (-) auxiliary battery terminal Below 1 Ω
A41-26 (GND3) - Body ground W-B - Body ground Skid control ECU (Brake booster with master cylinder assembly) ground 3 1 minute or more after disconnecting the cable from the negative (-) auxiliary battery terminal Below 1 Ω
A41-27 (GND2) - Body ground W-B - Body ground Skid control ECU (Brake booster with master cylinder assembly) ground 2 1 minute or more after disconnecting the cable from the negative (-) auxiliary battery terminal Below 1 Ω
A41-28 (GND) - Body ground W-B - Body ground Skid control ECU (Brake booster with master cylinder assembly) ground 1 minute or more after disconnecting the cable from the negative (-) auxiliary battery terminal Below 1 Ω
A41-33 (STP) - Body ground BR - Body ground Stop light switch assembly input Stop light switch assembly ON → OFF
(Brake pedal depressed → released)
11 to 14 V → Below 1.5 V
A41-36 (LBL) - Body ground P - Body ground Brake fluid level warning switch input Brake fluid level warning switch OFF → ON 1.84 to 2.16 kΩ → Below 1 Ω