Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM › 2011.12–2013.12
RM2170E _54 Brake _057021 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0278020 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C1234/34  Yaw Rate Sensor Malfunction  C1243/43  Acceleration Sensor Stuck Malfunction  C1244/44  Open or Short in Acceleration Sensor Circuit  C1245/45  Acceleration Sensor Output Malfunction  C1279/79  Acceleration Sensor Output Voltage Malfunction (Test Mode DTC)  C1381/97  Acceleration Sensor Power Supply Voltage Malfunction  


DESCRIPTION

The skid control ECU receives signals from the yaw rate and acceleration sensor (airbag sensor assembly) via the CAN communication system.

The airbag sensor assembly has a built-in yaw rate and acceleration sensor and detects the vehicle's condition using 2 circuits (GL1, GL2).

If there are any problems in the bus lines between the yaw rate and acceleration sensor (airbag sensor assembly) and the CAN communication system, DTCs U0123/62 (Lost Communication with Yaw Rate Sensor Module) and U0124/95 (Lost Communication with Lateral Acceleration Sensor Module) are stored.

These DTCs are also output when calibration has not been completed.

DTC C1279/79 will be cleared when the yaw rate and acceleration sensor (airbag sensor assembly) sends a yaw rate and/or acceleration signal or when Test Mode ends. DTC C1279/79 is output only in Test Mode.

DTC No. INF Code DTC Detection Condition Trouble Area
C1234/34 711 While yaw rate sensor communication is enabled, a malfunction signal output is received during the sensor self-check (Sensor 1 (GL1) malfunction). Yaw rate and acceleration sensor (Airbag sensor assembly) internal malfunction
↑ 712 While yaw rate sensor communication is enabled, a malfunction signal output is received during the sensor self-check (Sensor 2 (GL2) malfunction). ↑
↑ 713 While yaw rate sensor communication is enabled, a malfunction signal output is received during the sensor self-check (Zero point calibration malfunction). ↑
↑ 714 While yaw rate sensor communication is enabled, a malfunction signal output is received during the sensor self-check (Two-value comparison malfunction). ↑
C1243/43 561 An acceleration sensor malfunction occurs 16 times or more when the vehicle speed drops from above 30 km/h (19 mph) to 0 km/h (0 mph). Yaw rate and acceleration sensor (Airbag sensor assembly) internal stuck malfunction
↑ 562
563
564
565
A stuck acceleration sensor value is determined. ↑
C1244/44 571 Either of the following is detected:
1.

Difference between GL1 and GL2 does not become less than 0.4 G for 60 seconds or more after reaching 0.6 G when the vehicle is stopped.

2.

A malfunction signal from the acceleration sensor is received.


·

Yaw rate and acceleration sensor (Airbag sensor assembly) installed improperly

·

Yaw rate and acceleration sensor (Airbag sensor assembly)


C1245/45 581 Difference between longitudinal G calculated from the acceleration sensor value and that calculated from the vehicle speed exceeds 0.35 G for 60 seconds or more.
·

Yaw rate and acceleration sensor (Airbag sensor assembly) installed improperly

·

Yaw rate and acceleration sensor (Airbag sensor assembly)


C1381/97 601 While yaw rate and acceleration sensor communication is enabled, a supply voltage malfunction signal is received from the sensor for 10 seconds.
·

Yaw rate and acceleration sensor (Airbag sensor assembly) supply voltage shut down

·

Yaw rate and acceleration sensor (Airbag sensor assembly)

·

Skid control ECU (Brake booster with master cylinder assembly)


C1279/79 - Detected only during Test Mode.
·

Sensor installation

·

Yaw rate and acceleration sensor (Airbag sensor assembly)



WIRING DIAGRAM

C246787E26
0.073,4.042 0.354,4.198 0.281,0.156 10 false G18 4.99,4.031 7.104,4.385 2.115,0.354 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 6.052,1.302 6.479,1.448 0.427,0.146 10 false CA1H 6.052,0.677 6.479,0.823 0.427,0.146 10 false CA1L 4.677,4.031 4.938,4.188 0.26,0.156 10 false A41 5.802,1.198 6.031,1.354 0.229,0.156 10 false 37 5.802,0.594 6,0.75 0.198,0.156 10 false 38 3.896,1.948 4.896,2.104 1,0.156 10 false from IG2 Relay 2.146,2.083 2.802,2.24 0.656,0.156 10 false IG2 NO. 2 1.281,1.813 1.479,1.979 0.198,0.167 10 false 21 1.281,1.198 1.479,1.365 0.198,0.167 10 false 13 1.281,0.594 1.458,0.76 0.177,0.167 10 false 22 0.781,1.302 1.208,1.448 0.427,0.146 10 false CANH 0.938,1.906 1.24,2.052 0.302,0.146 10 false IG2 1.01,2.531 1.24,2.677 0.229,0.146 10 false E1 0.792,0.677 1.219,0.823 0.427,0.146 10 false CANL 0.396,4.042 2.573,4.365 2.177,0.323 10 false Yaw Rate and Acceleration Sensor (Airbag Sensor Assembly) 1.01,3.156 1.24,3.302 0.229,0.146 10 false E2 1.281,2.427 1.479,2.594 0.198,0.167 10 false 25 1.281,3.063 1.479,3.229 0.198,0.167 10 false 26 2.667,1.813 2.865,1.979 0.198,0.167 10 false 1 2.198,1.813 2.396,1.979 0.198,0.167 10 false 2

CAUTION / NOTICE / HINT

NOTICE:

When replacing the yaw rate and acceleration sensor (airbag sensor assembly), perform zero point calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>CALIBRATION).


HINT:

When U0123/62 and/or U0124/95 is output together with C1234/34, C1243/43, C1244/44, C1245/45, and/or C1381/97, inspect and repair the trouble areas indicated by U0123/62 and/or U0124/95 first (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>U0073/94).


PROCEDURE

1.CHECK DTC

b.

Turn the power switch off (lock).


c.

Turn the power switch on (ready).


d.

Drive the vehicle at a speed of 30 km/h (19 mph) or more, turn the steering wheel, and decelerate (depress the brake pedal) the vehicle.


e.

Turn the power switch on (IG) again and check that no CAN communication system DTC is output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).


f.

Check if DTC C1210/36 (Zero Point Calibration of Yaw Rate Sensor Undone) or C1336/98 (Zero Point Calibration of Acceleration Sensor Undone) is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTCs (C1210/36, C1336/98 and CAN communication system DTC) are not output. A
CAN communication system DTC is output. B
DTCs C1210/36 and/or C1336/98 are output. C




A

2.CHECK AIRBAG SENSOR ASSEMBLY INSTALLATION

B

C

2.CHECK AIRBAG SENSOR ASSEMBLY INSTALLATION
a.

Turn the power switch off (lock).


b.

Check that the yaw rate and acceleration sensor (airbag sensor assembly) has been installed properly (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>INSTALLATION).

OK:

The sensor is tightened to the specified torque.

The sensor is not tilted.




OK

3.CHECK HARNESS AND CONNECTOR (IG2 TERMINAL)

NG

3.CHECK HARNESS AND CONNECTOR (IG2 TERMINAL)
a.
U183534E02
1.031,2.177 0.573,2.844 false 0.354,0.823 0.635,1 0.281,0.177 10 false G18 0.24,0.219 0.458,0.396 0.219,0.177 10 false *a 0.385,2.865 0.677,3.042 0.292,0.177 10 false IG2

Make sure that there is no looseness at the locking part and the connecting part of the connector.


b.

Disconnect the yaw rate and acceleration sensor (airbag sensor assembly) connector.


c.

Turn the power switch on (IG).


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G18-21 (IG2) - Body ground Power switch on (IG) 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Yaw Rate and Acceleration Sensor (Airbag Sensor Assembly))



OK

4.CHECK HARNESS AND CONNECTOR (E TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (IG2 CIRCUIT)

4.CHECK HARNESS AND CONNECTOR (E TERMINAL)
a.
U183535E02
1.656,2.177 1.198,2.844 false 1.813,2.177 2.271,2.844 false 0.24,0.219 0.458,0.396 0.219,0.177 10 false *a 1.073,2.865 1.302,3.042 0.229,0.177 10 false E1 2.208,2.865 2.438,3.042 0.229,0.177 10 false E2 0.365,0.823 0.646,1 0.281,0.177 10 false G18

Turn the power switch off (lock).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G18-25 (E1) - Body ground 1 minute or more after disconnecting the cable from the negative (-) auxiliary battery terminal Below 1 Ω
G18-26 (E2) - Body ground 1 minute or more after disconnecting the cable from the negative (-) auxiliary battery terminal Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Yaw Rate and Acceleration Sensor (Airbag Sensor Assembly))

NOTICE:

Check the yaw rate and acceleration sensor signal after replacement (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>TEST MODE PROCEDURE).


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE).




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (E CIRCUIT)