Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM › 2011.12–2013.12
RM2170E _54 Brake _057021 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0278020 ELECTRONICALLY CONTROLLED BRAKE SYSTEM U

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  DATA LIST / ACTIVE TEST  


DATA LIST


HINT:

Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Warm up the engine.


b.

Turn the power switch off (lock).


c.

Connect the intelligent tester to the DLC3.


d.

Turn the power switch on (IG).


e.

Turn the intelligent tester on.


f.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.


g.

According to the display on the intelligent tester, read the Data List.

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
ABS Warning Light ABS warning light / ON or OFF ON: Warning light on
OFF: Warning light off
-
Brake Warning Light Brake warning light / red (malfunction) / ON or OFF ON: Warning light on
OFF: Warning light off
-
ECB* Warning Light Brake warning light / yellow (minor malfunction) / ON or OFF ON: Warning light on
OFF: Warning light off
-
Buzzer Meter buzzer / ON or OFF ON: Buzzer on
OFF: Buzzer off
-
Stop Light SW Stop light switch assembly / ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
-
Parking Brake SW Parking brake switch assembly / ON or OFF ON: Parking brake applied
OFF: Parking brake released
-
Reservoir Warning SW Brake fluid level warning switch / ON or OFF ON: Reservoir level low
OFF: Reservoir level normal
-
Main Idle SW Main idle switch / ON or OFF ON: Accelerator pedal released
OFF: Accelerator pedal depressed
-
Shift Lever Position Shift position information / Fail, 1st-6th/B, D/M, P,N or R Actual shift position -
Inspection Mode Inspection mode / Other or Inspect Other: Normal mode
Inspect: Inspection mode
-
Regulator Pressure Sensor Output Regulator pressure sensor output / Min.: 0.00 V, Max.: 5.00 V When brake pedal released: 0.10 to 0.90 V Reading increases when brake pedal is depressed
Stroke Sensor Brake pedal stroke sensor assembly / Min.: 0.00 V, Max.: 5.00 V When brake pedal released: 0.65 to 1.35 V Reading increases when brake pedal is depressed
Voltage of Stroke Sensor Voltage of brake pedal stroke sensor assembly / Min.: -2.50 V, Max.: 2.49 V - -
Stroke Sensor2 Brake pedal stroke sensor assembly 2 / Min.: 0.00 V, Max.: 5.00 V When brake pedal released: 3.65 to 4.35 V Reading decreases when brake pedal is depressed
Voltage of Stroke Sensor2 Voltage of brake pedal stroke sensor assembly 2 / Min.: -2.50 V, Max.: 2.49 V - -
Accumulator Sensor Accumulator pressure sensor / Min.: 0.00 V, Max.: 5.00 V Specified value: 2.90 to 4.20 V When brake fluid is stored in the accumulator: Accumulator pressure changes in accordance with volume of fluid stored in the accumulator
Deceleration Sensor Acceleration sensor 1 / Min.: -18.525 m/s2, Max.: 18.387 m/s2 - During deceleration/acceleration: Changes continuously
Zero Point of Decele Memorized zero value / Min.: -25.10 m/s2, Max.: 24.90 m/s2 - -
Deceleration Sensor2 Acceleration sensor 2 / Min.: -18.525 m/s2, Max.: 18.387 m/s2 - During deceleration/acceleration: Changes continuously
Zero Point of Decele2 Memorized zero value / Min.: -25.10 m/s2, Max.: 24.90 m/s2 - -
Yaw Rate Sensor Yaw rate sensor 1 / Min.: -128°/s, Max.: 127°/s Vehicle stationary: 0°/s
Turning right: -128 to 0°/s
Turning left: 0 to 127°/s
-
Zero Point of Yaw Rate Memorized zero value / Min.: -128°, Max.: 127° - After completing zero point calibration: 0°
Yaw Rate Sensor2 Yaw rate sensor 2 / Min.: -128°/s, Max.: 127°/s Vehicle stationary: 0°/s
Turning right: -128 to 0°/s
Turning left: 0 to 127°/s
-
Zero Point of Yaw Rate2 Memorized zero value / Min.: -128°/s, Max.: 127°/s - After completing zero point calibration: 0°/s
Steering Angle Sensor Steering angle sensor / Min.: -3276.8°, Max.: 3276.7° Turning left: Increases
Turning right: Decreases
-
Zero Point of Steering Angle Memorized zero value / Min.: -3276.8°, Max.: 3276.7° - After clearing zero point calibration: 0°
Lateral G Lateral G / Min.: -25.10 m/s2, Max.: 24.90 m/s2 - During turning: Changes in proportion with lateral acceleration
Forward and Rearward G Forward and backward G / Min.: -25.10 m/s2, Max.: 24.90 m/s2 - During acceleration/deceleration: Changes in proportion with acceleration
Yaw Rate Value Yaw rate value / Min.: -128°/s, Max.: 127°/s - During turning: Changes in proportion with yaw
Steering Angle Value Steering angle value / Min.: -3276.8°, Max.: 3276.7° - During steering operation: Changes in proportion with steering wheel rotation
Slip Indicator Light Slip indicator light / ON or OFF ON: Indicator light on
OFF: Indicator light off
-
FR Wheel Speed Front speed sensor RH / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
FL Wheel Speed Front speed sensor LH / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
RR Wheel Speed Rear speed sensor RH / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
RL Wheel Speed Rear speed sensor LH / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
Vehicle Speed Maximum wheel speed sensor / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
FR Wheel Acceleration Front wheel RH acceleration / Min.: -200.84 m/s2, Max.: 199.27 m/s2 - During deceleration/acceleration: Changes continuously
FL Wheel Acceleration Front wheel LH acceleration / Min.: -200.84 m/s2, Max.: 199.27 m/s2 - During deceleration/acceleration: Changes continuously
RR Wheel Acceleration Rear wheel RH acceleration / Min.: -200.84 m/s2, Max.: 199.27 m/s2 - During deceleration/acceleration: Changes continuously
RL Wheel Acceleration Rear wheel LH acceleration / Min.: -200.84 m/s2, Max.: 199.27 m/s2 - During deceleration/acceleration: Changes continuously
Stop Light Relay Output Stop light control relay (Stop light switch assembly) output / ON or OFF ON: Relay output on
OFF: Relay output off
-
EBS Relay Stop light control relay (Emergency brake signal) / ON or OFF OFF No change
FR Wheel ABS Ctrl Status Front wheel RH ABS control status / ON or OFF ON: During control -
FL Wheel ABS Ctrl Status Front wheel LH ABS control status / ON or OFF ON: During control -
RR Wheel ABS Ctrl Status Rear wheel RH ABS control status / ON or OFF ON: During control -
RL Wheel ABS Ctrl Status Rear wheel LH ABS control status / ON or OFF ON: During control -
RR Wheel EBD Ctrl Status Rear wheel RH EBD control status / ON or OFF ON: During control -
RL Wheel EBD Ctrl Status Rear wheel LH EBD control status / ON or OFF ON: During control -
BA Ctrl Status BA control status / ON or OFF ON: During control -
PBA Ctrl Status PBA control status / ON or OFF OFF No change
TRC(TRAC) Ctrl Status TRC control status / ON or OFF ON: During control -
TRC(TRAC) Engine Ctrl Status TRC engine control status / ON or OFF ON: During control -
TRC(TRAC) Brake Ctrl Status TRC brake control status / ON or OFF ON: During control -
FR Wheel VSC Ctrl Status Front wheel RH VSC control status / ON or OFF ON: During control -
FL Wheel VSC Ctrl Status Front wheel LH VSC control status / ON or OFF ON: During control -
RR Wheel VSC Ctrl Status Rear wheel RH VSC control status / ON or OFF ON: During control -
RL Wheel VSC Ctrl Status Rear wheel LH VSC control status / ON or OFF ON: During control -
Accelerator Opening Angle % The difference of a present accelerator / Min.: 0.0%, Max.: 128.0% When the accelerator pedal released: 0.0% During accelerator pedal operation: Changes in proportion with the pedal movement
Regenerative Cooperation Regenerative cooperation / ON or OFF ON: Operate
OFF: Not operate
-
FR Regenerative Request FR regenerative request torque / Min.: 0 Nm, Max.: 1048560 Nm - Changes according to brake pedal force
(When depressing the brake pedal lightly after reaching 30 km/h (19 mph) or more, avoiding sudden braking.)
FR Regenerative Operation FR regenerative operation torque / Min.: 0 Nm, Max.: 1048560 Nm - Changes according to brake pedal force
(When depressing the brake pedal lightly after reaching 30 km/h (19 mph) or more, avoiding sudden braking.)
ECB* Motor Relay ABS motor relay / ON or OFF ON: Relay on
OFF: Relay off
-
ECB* Main Relay ABS main relay / ON or OFF ON: Relay on
OFF: Relay off
-
ABS Solenoid (SFRH) Holding solenoid valve (FRH) / ON or OFF ON: Operate
OFF: Not operate
-
ABS Solenoid (SFRR) Reduction solenoid valve (FRR) / ON or OFF ON: Operate
OFF: Not operate
-
ABS Solenoid (SFLH) Holding solenoid valve (FLH) / ON or OFF ON: Operate
OFF: Not operate
-
ABS Solenoid (SFLR) Reduction solenoid valve (FLR) / ON or OFF ON: Operate
OFF: Not operate
-
ABS Solenoid (SRRH) Holding solenoid valve (RRH) / ON or OFF ON: Operate
OFF: Not operate
-
ABS Solenoid (SRRR) Reduction solenoid valve (RRR) / ON or OFF ON: Operate
OFF: Not operate
-
ABS Solenoid (SRLH) Holding solenoid valve (RLH) / ON or OFF ON: Operate
OFF: Not operate
-
ABS Solenoid (SRLR) Reduction solenoid valve (RLR) / ON or OFF ON: Operate
OFF: Not operate
-
ECB* Solenoid (SRC) Regulator cut solenoid valve (SRC) / ON or OFF ON: Operate
OFF: Not operate
-
ECB* Solenoid (SCC) Switching solenoid valve (SCC) / ON or OFF ON: Operate
OFF: Not operate
-
ECB* Solenoid (SMC) Master cut solenoid valve (SMC) / ON or OFF ON: Operate
OFF: Not operate
-
ECB* Solenoid (SSC) Simulator cut solenoid valve (SSC) / ON or OFF ON: Operate
OFF: Not operate
-
Regulator Pressure Sensor Correction Voltage Voltage of regulator pressure sensor / Min.: -2.50 V, Max.: 2.49 V - -
FR Speed Open Front speed sensor RH open detection / Error or Normal Error: Momentary interruption
Normal: Normal
-
FL Speed Open Front speed sensor LH open detection / Error or Normal Error: Momentary interruption
Normal: Normal
-
RR Speed Open Rear speed sensor RH open detection / Error or Normal Error: Momentary interruption
Normal: Normal
-
RL Speed Open Rear speed sensor LH open detection / Error or Normal Error: Momentary interruption
Normal: Normal
-
Yaw Rate Open Yaw rate sensor open detection / Error or Normal Error: Momentary interruption
Normal: Normal
-
Deceleration Open Acceleration sensor open detection / Error or Normal Error: Momentary interruption
Normal: Normal
-
Steering Open Steering angle sensor open detection / Error or Normal Error: Momentary interruption
Normal: Normal
-
Master Cylinder Open Regulator pressure sensor open detection / Error or Normal Error: Momentary interruption
Normal: Normal
-
Stroke Open Brake pedal stroke sensor assembly open detection / Error or Normal Error: Momentary interruption
Normal: Normal
-
FR Wheel Cylinder Open Wheel cylinder pressure sensor open detection / Error or Normal Error: Momentary interruption
Normal: Normal
-
Accumulator Open Accumulator pressure sensor open detection / Error or Normal Error: Momentary interruption
Normal: Normal
-
HV Communication Open Hybrid vehicle communication open detection / Error or Normal Error: Momentary interruption
Normal: Normal
-
Number of DTC Number of DTC / Min.: 0, Max.: 255 - Number of DTC output is displayed
Wheel Cylinder Pressure Sensor Wheel cylinder pressure sensor / Min.: 0.00 V, Max.: 5.00 V When brake pedal released: 0.10 to 0.90 V Reading increases when brake pedal is depressed
Regulator Pressure Sensor Output After Filter Regulator pressure sensor output after filter / Min.: -1.00 MPa, Max.: 23.99 MPa - -
Regulator Pressure Sensor Variation Regulator pressure sensor variation / Min.: -30 MPa/s, Max.: 225 MPa/s - -
SLA Solenoid Current Linear solenoid additional valve (SLA) current / Min.: 0.00 A, Max.: 3.00 A When brake pedal released: 0.00 A -
SLR Solenoid Current Linear solenoid reduction valve (SLR) current / Min.: 0.00 A, Max.: 3.00 A When brake pedal released: 0.00 A -
SSC Solenoid Current Simulator cut solenoid valve (SSC) current / Min.: 0.00 A, Max.: 3.00 A When brake pedal released: 0.00 A -
SCC Solenoid Current Switching solenoid valve (SCC) current / Min.: 0.00 A, Max.: 3.00 A When brake pedal released: 0.00 A -
SMC Solenoid Current Master cut solenoid valve (SMC) current / Min.: 0.00 A, Max.: 3.00 A When brake pedal released: 0.00 A -
SRC Solenoid Current Regulator cut solenoid valve (SRC) current / Min.: 0.00 A, Max.: 3.00 A When brake pedal released: 0.00 A -

*: Electronically Controlled Brake System



ACTIVE TEST


HINT:

Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts to operate without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.

Warm up the engine.


b.

Turn the power switch off (lock).


c.

Connect the intelligent tester to the DLC3.


d.

Turn the power switch on (IG).


e.

Turn the intelligent tester on.


f.

Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.


g.

According to the display on the intelligent tester, perform the Active Test.

ABS/VSC/TRC
Tester Display Test Part Control Range Diagnostic Note
ABS Warning Light ABS warning light Warning light ON/OFF Observe combination meter assembly
Brake Warning Light Brake warning light / red (malfunction) Warning light ON/OFF Observe combination meter assembly
ECB* Warning Light Brake warning light / yellow (minor malfunction) Warning light ON/OFF Observe combination meter assembly
Buzzer Meter buzzer Buzzer ON/OFF Buzzer can be heard
Stop Light Relay Stop light control relay (Stop light switch assembly) Relay (Switch) ON/OFF Stop lights come on
ECB* Main Relay ABS main relay Relay ON/OFF -
ECB* Motor Relay ABS motor relay Relay ON/OFF -
ABS Solenoid (SRLR) Reduction solenoid valve (RLR) Solenoid ON/OFF Operation sound of solenoid (clicking sound) can be heard
ABS Solenoid (SRLH) Holding solenoid valve (RLH) Solenoid ON/OFF Operation sound of solenoid (clicking sound) can be heard
ABS Solenoid (SRRR) Reduction solenoid valve (RRR) Solenoid ON/OFF Operation sound of solenoid (clicking sound) can be heard
ABS Solenoid (SRRH) Holding solenoid valve (RRH) Solenoid ON/OFF Operation sound of solenoid (clicking sound) can be heard
ABS Solenoid (SFLR) Reduction solenoid valve (FLR) Solenoid ON/OFF Operation sound of solenoid (clicking sound) can be heard
ABS Solenoid (SFLH) Holding solenoid valve (FLH) Solenoid ON/OFF Operation sound of solenoid (clicking sound) can be heard
ABS Solenoid (SFRR) Reduction solenoid valve (FRR) Solenoid ON/OFF Operation sound of solenoid (clicking sound) can be heard
ABS Solenoid (SFRH) Holding solenoid valve (FRH) Solenoid ON/OFF Operation sound of solenoid (clicking sound) can be heard
ECB* Control Invalid Electronically controlled brake system control invalid Control invalid ON/OFF Electronically controlled brake system control is disabled (braking with no accumulator assist)
Accumulator Zero Down Reduction of pressure in accumulator Activation ON/OFF Brake fluid in the accumulator makes noise
Actuator Air Bleeding Pattern Actuator air bleeding pattern activation Activation ON/OFF When accumulator pressure drops, pump operation creates sound
Power Supply Air Bleeding Pattern1 Power supply air bleeding pattern activation 1 Activation ON/OFF When accumulator pressure drops, pump operation creates sound
Power Supply Air Bleeding Pattern2 Power supply air bleeding pattern activation 2 Activation ON/OFF When accumulator pressure drops, pump operation creates sound
Slip Indicator Light Slip indicator light Indicator light ON/OFF Observe combination meter assembly
ECB* Solenoid (SLR) Linear solenoid reduction valve (SLR) Solenoid ON/OFF -
ECB* Solenoid (SLA) Linear solenoid addition valve (SLA) Solenoid ON/OFF -
Stroke Simulator Cut Valve Pattern Simulator cut solenoid valve (SSC) Pattern activation ON/OFF (Difficult to identify visually)
ECB* Solenoid (SRC) Regulator cut solenoid valve (SRC) Solenoid ON/OFF Operation sound of solenoid (clicking sound) can be heard
ECB* Solenoid (SMC) Master cut solenoid valve (SMC) Solenoid ON/OFF Operation sound of solenoid (clicking sound) can be heard
ECB* Solenoid (SCC) Switching solenoid valve (SCC) Solenoid ON/OFF Operation sound of solenoid (clicking sound) can be heard
ECB* Solenoid (SSC) Simulator cut solenoid valve (SSC) Solenoid ON/OFF Operation sound of solenoid (clicking sound) can be heard
ECB* Solenoid (SMC/SRC/SCC) Switching solenoid valve (SMC/SRC/SCC) Solenoid ON/OFF Operation sound of solenoid (clicking sound) can be heard

*: Electronically Controlled Brake System