Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM › 2015.11–2017.06
RM2170E _54 Brake _057021 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0278020 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  U0073/94  Control Module Communication Bus OFF  U0120/96  Lost Communication with Starter / Generator Control Module  U0123/62  Lost Communication with Yaw Rate Sensor Module  U0124/95  Lost Communication with Lateral Acceleration Sensor Module  U0126/63  Lost Communication with Steering Angle Sensor Module  U0293/59  Communication Error from HV ECU  


DESCRIPTION

The skid control ECU receives signals from the hybrid vehicle control ECU, steering angle sensor (spiral cable with sensor sub-assembly), certification ECU (smart key ECU assembly) and yaw rate and acceleration sensor (airbag sensor assembly) via the CAN communication system.

DTC No. INF Code DTC Detection Condition Trouble Area
U0073/94 461 Either of the following is detected:
1.

Yaw rate and acceleration sensor communication is disabled for 1 second or more.

2.

Yaw rate and acceleration sensor communication is disabled once or more per 5 seconds 10 times or more within 60 seconds.


·

CAN communication line (V bus)

·

Yaw rate and acceleration sensor (Airbag sensor assembly)

·

Skid control ECU (Brake booster with master cylinder assembly)


↑ 462 Either of the following is detected:
1.

Steering angle sensor communication is disabled for 1 second or more.

2.

Steering angle sensor communication is disabled once or more per 5 seconds 10 times or more within 60 seconds.


·

CAN communication line (V bus)

·

Steering angle sensor (Spiral cable with sensor sub-assembly)

·

Skid control ECU (Brake booster with master cylinder assembly)


↑ 463
464
Bus off occurs once or more per 0.1 seconds 10 times repeatedly.
·

CAN communication line

·

Skid control ECU (Brake booster with master cylinder assembly)


↑ 465
466
Sending does not complete within 5 seconds after data is output from the skid control ECU. ↑
U0120/96 471 Push start switch data is invalid for 3 seconds or more.
·

CAN communication line (V bus)

·

Certification ECU (Smart key ECU assembly)

·

Skid control ECU (Brake booster with master cylinder assembly)


U0123/62 731 Yaw rate sensor communication is disabled for 1 second or more.
·

CAN communication line (V bus)

·

Yaw rate and acceleration sensor (Airbag sensor assembly)

·

Skid control ECU (Brake booster with master cylinder assembly)


↑ 732 Yaw rate sensor communication is disabled once or more per 5 seconds 10 times or more within 60 seconds. ↑
U0124/95 591 Acceleration sensor communication is disabled for 1 second or more.
·

CAN communication line (V bus)

·

Yaw rate and acceleration sensor (Airbag sensor assembly)

·

Skid control ECU (Brake booster with master cylinder assembly)


↑ 592 Acceleration sensor communication is disabled once per 5 seconds 10 times or more within 60 seconds. ↑
U0126/63 741 Steering angle sensor communication is disabled for 1 second or more.
·

CAN communication line (V bus)

·

Steering angle sensor (Spiral cable with sensor sub-assembly)

·

Skid control ECU (Brake booster with master cylinder assembly)


↑ 742 Steering angle sensor communication is disabled once or more per 5 seconds 10 times or more within 60 seconds. ↑
U0293/59 411
412
413
Either of the following is detected:
1.

With the IG2 terminal voltage 9.5 V or more, data from the hybrid vehicle control ECU cannot be received for 2 seconds or more.

2.

With the IG2 terminal voltage 9.5 V or more, data from the hybrid vehicle control ECU cannot be received once or more within 5 seconds occur 10 times in succession.


·

CAN communication line (Sub bus 15)

·

Hybrid vehicle control ECU

·

Skid control ECU (Brake booster with master cylinder assembly)



WIRING DIAGRAM

C319737E12
2.01,8.021 3.5,8.385 1.49,0.365 10 false Hybrid Vehicle Control ECU 0.021,1.594 1.708,2.115 1.688,0.521 10 false Yaw Rate and Acceleration Sensor (Airbag Sensor Assembly) 0.344,5.302 1.771,5.813 1.427,0.51 10 false Steering Angle Sensor (Spiral Cable with Sensor Sub-assembly) 5.729,1.156 5.917,1.302 0.188,0.146 10 false 38 5.729,0.542 5.917,0.688 0.188,0.146 10 false 37 1.198,1.135 1.406,1.292 0.208,0.156 10 false 22 1.198,0.542 1.406,0.698 0.208,0.156 10 false 13 1.219,4.823 1.333,4.979 0.115,0.156 10 false 3 1.219,4.448 1.396,4.604 0.177,0.156 10 false 4 0.76,1.26 1.156,1.406 0.396,0.146 10 false CANL 0.729,0.625 1.156,0.771 0.427,0.146 10 false CANH 5.979,1.229 6.375,1.375 0.396,0.146 10 false CA1L 5.979,0.635 6.406,0.781 0.427,0.146 10 false CA1H 0.75,4.938 1.146,5.083 0.396,0.146 10 false CANL 0.719,4.542 1.146,4.688 0.427,0.146 10 false CANH 1.677,8.021 2.021,8.167 0.344,0.146 10 false G81 2.073,5.313 2.354,5.469 0.281,0.156 10 false G72 2.375,5.313 3.188,5.615 0.813,0.302 10 false Junction Connector 0.021,5.302 0.302,5.448 0.281,0.146 10 false G30 0.021,1.438 0.302,1.583 0.281,0.146 10 false G18 3.01,7.021 3.198,7.167 0.188,0.146 10 false 31 3.01,7.5 3.198,7.646 0.188,0.146 10 false 30 2.5,7.104 2.896,7.25 0.396,0.146 10 false CA3P 2.5,7.594 2.948,7.74 0.448,0.146 10 false CA3N 5.969,7.604 6.365,7.75 0.396,0.146 10 false CA2L 5.969,7.104 6.396,7.25 0.427,0.146 10 false CA2H 5.729,7.01 5.927,7.167 0.198,0.156 10 false 35 5.729,7.51 5.927,7.667 0.198,0.156 10 false 34 3.073,0.542 3.26,0.698 0.188,0.156 10 false 10 5.219,8 5.542,8.146 0.323,0.146 10 false A41 5.552,8 7.146,8.51 1.594,0.51 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 3.854,0.417 4.042,0.573 0.188,0.156 10 false 4 3.813,1.052 4.01,1.208 0.198,0.156 10 false 15 3.073,1.135 3.26,1.292 0.188,0.156 10 false 21 1.896,0.542 1.99,0.698 0.094,0.156 10 false 4 1.823,1.135 2,1.292 0.177,0.156 10 false 15 3.771,1.26 4.063,1.406 0.292,0.146 10 false G86 3.771,0.625 4.063,0.771 0.292,0.146 10 false G86 5.198,1.26 5.552,1.406 0.354,0.146 10 false A74 5.198,0.625 5.552,0.771 0.354,0.146 10 false A74 5.24,0.417 5.427,0.573 0.188,0.156 10 false 10 5.24,1.063 5.438,1.219 0.198,0.156 10 false 21 3.802,6.896 4,7.052 0.198,0.156 10 false 10 3.771,7.104 4.063,7.25 0.292,0.146 10 false G86 5.198,7.104 5.552,7.25 0.354,0.146 10 false A74 5.271,6.885 5.469,7.042 0.198,0.156 10 false 1 3.823,7.385 4.021,7.542 0.198,0.156 10 false 21 3.771,7.594 4.063,7.74 0.292,0.146 10 false G86 5.198,7.604 5.552,7.75 0.354,0.146 10 false A74 5.229,7.396 5.427,7.552 0.198,0.156 10 false 12 1.917,4.438 2.01,4.594 0.094,0.156 10 false 1 1.833,4.813 2.01,4.969 0.177,0.156 10 false 12 3.875,5.896 4.063,6.052 0.188,0.156 10 false 2 3.823,6.417 4.021,6.573 0.198,0.156 10 false 13 3.771,6.625 4.125,6.771 0.354,0.146 10 false G86 3.771,6.115 4.125,6.26 0.354,0.146 10 false G86 4.125,8 4.844,8.365 0.719,0.365 10 false Junction Connector 2.51,6.625 2.906,6.771 0.396,0.146 10 false CA1L 2.5,6.135 2.927,6.281 0.427,0.146 10 false CA1H 3.01,6.521 3.198,6.667 0.188,0.146 10 false 24 3.01,6.031 3.198,6.177 0.188,0.146 10 false 25 0.01,3.604 0.292,3.75 0.281,0.146 10 false G79 0.01,3.771 1.906,4.073 1.896,0.302 10 false Certification ECU (Smart Key ECU Assembly) 0.719,2.875 1.146,3.021 0.427,0.146 10 false CANH 0.74,3.344 1.135,3.49 0.396,0.146 10 false CANL 1.208,2.76 1.396,2.906 0.188,0.146 10 false 14 1.208,3.229 1.396,3.375 0.188,0.146 10 false 15 1.885,2.76 2.073,2.906 0.188,0.146 10 false 3 1.813,3.24 2,3.385 0.188,0.146 10 false 14 0.125,0.01 0.833,0.188 0.708,0.177 12 false for LHD:

C322207E06
2.052,8.01 3.542,8.375 1.49,0.365 10 false Hybrid Vehicle Control ECU 0.052,1.542 1.74,2.063 1.688,0.521 10 false Yaw Rate and Acceleration Sensor (Airbag Sensor Assembly) 0.323,3.49 1.75,4 1.427,0.51 10 false Steering Angle Sensor (Spiral Cable with Sensor Sub-assembly) 5.74,1.156 5.927,1.302 0.188,0.146 10 false 38 5.74,0.542 5.927,0.688 0.188,0.146 10 false 37 1.24,1.125 1.448,1.281 0.208,0.156 10 false 22 1.24,0.542 1.448,0.698 0.208,0.156 10 false 13 1.26,3.063 1.375,3.219 0.115,0.156 10 false 3 1.271,2.604 1.448,2.76 0.177,0.156 10 false 4 0.781,1.229 1.177,1.375 0.396,0.146 10 false CANL 0.75,0.625 1.177,0.771 0.427,0.146 10 false CANH 6.01,1.229 6.406,1.375 0.396,0.146 10 false CA1L 6.01,0.635 6.438,0.781 0.427,0.146 10 false CA1H 0.781,5.229 1.177,5.375 0.396,0.146 10 false CANL 0.76,4.635 1.188,4.781 0.427,0.146 10 false CANH 1.74,8.01 2.021,8.156 0.281,0.146 10 false G81 2.125,3.49 2.406,3.646 0.281,0.156 10 false G72 2.427,3.49 3.24,3.792 0.813,0.302 10 false Junction Connector 0,3.49 0.281,3.635 0.281,0.146 10 false G30 0.052,1.375 0.333,1.521 0.281,0.146 10 false G18 3.042,7.021 3.229,7.167 0.188,0.146 10 false 31 3.042,7.5 3.229,7.646 0.188,0.146 10 false 30 2.531,7.104 2.927,7.25 0.396,0.146 10 false CA3P 2.531,7.594 2.979,7.74 0.448,0.146 10 false CA3N 6,7.604 6.396,7.75 0.396,0.146 10 false CA2L 6,7.104 6.427,7.25 0.427,0.146 10 false CA2H 5.74,7.01 5.938,7.167 0.198,0.156 10 false 35 5.74,7.51 5.938,7.667 0.198,0.156 10 false 34 3.104,0.542 3.292,0.698 0.188,0.156 10 false 10 5.26,8.01 5.583,8.156 0.323,0.146 10 false A41 5.552,8.01 7.146,8.521 1.594,0.51 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 3.896,0.417 4.083,0.573 0.188,0.156 10 false 4 3.854,1.052 4.052,1.208 0.198,0.156 10 false 15 3.104,1.135 3.292,1.292 0.188,0.156 10 false 21 1.927,0.542 2.021,0.698 0.094,0.156 10 false 4 1.854,1.135 2.031,1.292 0.177,0.156 10 false 15 3.771,1.271 4.063,1.417 0.292,0.146 10 false G86 3.771,0.635 4.063,0.781 0.292,0.146 10 false G86 5.198,1.271 5.552,1.417 0.354,0.146 10 false A74 5.198,0.646 5.552,0.792 0.354,0.146 10 false A74 5.281,0.417 5.469,0.573 0.188,0.156 10 false 10 5.281,1.063 5.479,1.219 0.198,0.156 10 false 21 3.844,6.896 4.042,7.052 0.198,0.156 10 false 10 3.76,7.115 4.052,7.26 0.292,0.146 10 false G86 5.188,7.115 5.542,7.26 0.354,0.146 10 false A74 5.313,6.885 5.51,7.042 0.198,0.156 10 false 1 3.854,7.385 4.052,7.542 0.198,0.156 10 false 21 3.771,7.615 4.063,7.76 0.292,0.146 10 false G86 5.188,7.615 5.542,7.76 0.354,0.146 10 false A74 5.271,7.396 5.469,7.552 0.198,0.156 10 false 12 1.927,2.594 2.021,2.75 0.094,0.156 10 false 1 1.865,3.063 2.042,3.219 0.177,0.156 10 false 12 3.896,5.896 4.083,6.052 0.188,0.156 10 false 2 3.854,6.417 4.052,6.573 0.198,0.156 10 false 13 3.771,6.646 4.125,6.792 0.354,0.146 10 false G86 3.76,6.135 4.115,6.281 0.354,0.146 10 false G86 4.156,8 4.875,8.365 0.719,0.365 10 false Junction Connector 2.552,6.625 2.948,6.771 0.396,0.146 10 false CA1L 2.531,6.135 2.958,6.281 0.427,0.146 10 false CA1H 3.042,6.521 3.229,6.667 0.188,0.146 10 false 24 3.042,6.031 3.229,6.177 0.188,0.146 10 false 25 0.031,5.396 0.354,5.542 0.323,0.146 10 false G79 0.031,5.563 1.573,6.021 1.542,0.458 10 false Certification ECU (Smart Key ECU Assembly) 0.75,2.698 1.177,2.844 0.427,0.146 10 false CANH 0.781,3.167 1.177,3.313 0.396,0.146 10 false CANL 3.844,5.031 4.031,5.177 0.188,0.146 10 false 14 1.26,5.135 1.448,5.281 0.188,0.146 10 false 15 3.896,4.438 4.083,4.583 0.188,0.146 10 false 3 1.26,4.542 1.448,4.688 0.188,0.146 10 false 14 0.156,0.01 0.865,0.188 0.708,0.177 12 false for RHD: 3.76,4.656 4.115,4.802 0.354,0.146 10 false G86 3.771,5.25 4.125,5.396 0.354,0.146 10 false G86

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)
a.

Using the intelligent tester, check for any momentary interruptions in the wire harness and connector corresponding to a DTC (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>CHECK FOR INTERMITTENT PROBLEMS).

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Yaw Rate Open Yaw rate sensor open detection / Error or Normal Error: Momentary interruption
Normal: Normal
-
Steering Open Steering angle sensor open detection / Error or Normal Error: Momentary interruption
Normal: Normal
-
HV Communication Open Hybrid vehicle communication open detection / Error or Normal Error: Momentary interruption
Normal: Normal
-

Result:
Result Proceed to
There is a constant open circuit. A
There are no momentary interruptions. B
There are momentary interruptions. C


HINT:

Perform the above inspection before disconnecting any sensors or connectors.




A

2.CHECK IF EACH SENSOR AND ECU CONNECTOR IS SECURELY CONNECTED

B

3.RECONFIRM DTC

C

4.REPAIR OR REPLACE HARNESS OR CONNECTOR
2.CHECK IF EACH SENSOR AND ECU CONNECTOR IS SECURELY CONNECTED
a.

Turn the power switch off (lock).


b.

Check if each sensor and ECU connector is securely connected.

OK:

Each sensor and ECU connector is securely connected.




OK

3.RECONFIRM DTC

NG

CONNECT CONNECTOR TO EACH SENSOR OR ECU CORRECTLY

3.RECONFIRM DTC
a.

Turn the power switch off (lock).


b.

Record the output DTCs (for ABS, VSC, electronically controlled brake system, and/or CAN communication system) (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR for ABS, VSC and/or electronically controlled brake system, or Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM for CAN communication system).

HINT:

If the CAN communication system DTC and the relevant sensor DTCs are output simultaneously, troubleshoot the relevant sensor DTCs (for ABS, VSC and/or electronically controlled brake system) after the CAN communication system returns to normal.


Result:
Result Proceed to
DTC is not output. A
ABS, VSC and/or electronically controlled brake system DTC is output. B
CAN communication system DTC is output. C




A

B

C

4.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Turn the power switch off (lock).


b.

Repair or replace the harness or connector.


c.

Check for any momentary interruption between the skid control ECU (brake booster with master cylinder assembly) and each sensor or ECU (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>CHECK FOR INTERMITTENT PROBLEMS).



NEXT

5.RECONFIRM DTC
5.RECONFIRM DTC
a.

Turn the power switch off (lock).



c.

Turn the power switch on (ready).


d.

Drive the vehicle at a speed of 15 km/h (9 mph) or more and turn the steering wheel to the right and left.


e.

Check that no CAN communication system DTC is output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).


f.

If ABS, VSC and/or electronically controlled brake system DTCs are output, record them (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC is not output. A
ABS, VSC and/or electronically controlled brake system DTC is output. B
CAN communication system DTC is output. C


HINT:

The CAN communication system must be normal when performing troubleshooting for sensor DTCs (for ABS, VSC and/or electronically controlled brake system).




A

END

B

C