Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE BOOSTER PUMP(for LHD) › 2011.12–2014.12
RM2170E _54 Brake _057022 BRAKE SYSTEM (OTHER) _0278035 BRAKE BOOSTER PUMP(for LHD) A

BRAKE SYSTEM (OTHER)  BRAKE BOOSTER PUMP(for LHD)  INSTALLATION  


PROCEDURE

Hide 44590 1.INSTALL BRAKE ACTUATOR BRACKET ASSEMBLY

a.

Engage the clamp to install the frame wire to the brake actuator bracket assembly.


b.
C249860E02
1.219,1.615 1.458,1.802 0.24,0.188 10 true (1) 2.302,1.74 2.531,1.906 0.229,0.167 10 false (2) 3.042,1.104 3.271,1.271 0.229,0.167 10 false (3)

Install the brake actuator bracket assembly with the 3 bolts.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)

NOTICE:
·

Do not kink or damage the brake lines.

·

Tighten the 3 bolts in the order in the illustration.




c.

Engage the 2 clamps to install the frame wire to the brake actuator bracket assembly.


Hide 51442C 2.INSTALL ENGINE UNDER COVER LH

Hide 3.INSTALL FRONT WHEEL LH

Torque:
103 N*m (1050 kgf*cm, 76 ft.*lbf)

Hide 47070 4.INSTALL BRAKE BOOSTER PUMP ASSEMBLY

a.
U159530E04
1.302,2.781 1,2.781 false 0.813,2.219 0.625,2.219 false 1.344,3.552 1.344,4.406 1.344,4.406 1.698,3.479 true 2.229,4.302 2.833,4.302 2.833,4.302 2.76,3.896 false 1.094,1.792 1.24,1.646 1.24,1.646 1.438,1.646 true 2.135,1.229 2.135,1.438 2.135,1.438 1.594,1.115 true 0.833,2.698 0.979,2.844 0.146,0.146 10 false *1 0.469,2.146 0.615,2.292 0.146,0.146 10 false *4 1.479,1.583 1.625,1.729 0.146,0.146 10 false *5 2.063,1.469 2.292,1.729 0.229,0.26 10 false *6 1.26,4.427 1.479,4.646 0.219,0.219 10 false *2 2.854,4.219 3,4.365 0.146,0.146 10 false *3

Install the brake booster pump assembly to the brake actuator bracket assembly with the 2 brake booster pump bushings, 2 brake actuator case collars and 2 nuts.

Text in Illustration
*1 Union
*2 Connector
*3 Stud
*4 Brake Booster Pump Collar
*5 Brake Booster Pump Bushing
*6 Brake Actuator Bracket Cushion

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)

NOTICE:
·

Do not carry the brake booster pump assembly by the parts shown in bold (*1, *2 and *3) in the illustration.

·

Do not drop the brake booster pump assembly when carrying it. If the brake booster pump assembly has been dropped, replace it with a new one.

·

Do not kink or damage the brake lines. If they are damaged, replace them with new ones.

·

Be careful not to allow any brake fluid to enter the connector.

·

When installing the brake booster pump assembly to the brake actuator bracket assembly, confirm that the brake booster pump collar*4 and brake booster pump bushing*5 are installed on the brake booster pump assembly, and 2 brake actuator bracket cushions*6 are installed on the brake actuator bracket assembly.

·

If installing a new brake booster pump assembly, do not remove the hole plug before connecting the brake lines because the brake booster pump assembly is filled with brake fluid.




b.

Connect the 2 connectors to the brake booster pump assembly.


Hide 47381 5.INSTALL NO. 1 BRAKE TUBE CLAMP BRACKET

a.

Install the No. 1 brake tube clamp bracket to the brake booster pump assembly with the bolt.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)


Hide 47311 6.INSTALL FRONT NO. 1 BRAKE TUBE

a.

Temporarily tighten the union nut of the front No. 1 brake tube to the brake booster pump assembly.


b.

Install the bolt to secure the front No. 1 brake tube to the No. 1 brake tube clamp bracket.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)


c.

Using a union nut wrench, fully tighten the front No. 1 brake tube.

Torque:
15 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:

Use the formula to calculate special torque values for situations where the union nut wrench is combined with a torque wrench (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



Hide 44571 7.INSTALL BRAKE ACTUATOR HOSE

a.
C274355E01
0.333,0.127 3.043,2 2.71,1.873 1.688,0.127 1.688,2 false 0.387,0.178 0.684,0.403 0.297,0.225 12 *A 1.721,0.178 2.018,0.403 0.297,0.225 12 *B 1.453,0.281 1.618,0.435 0.165,0.153 10 *a 1.307,0.378 1.453,0.378 false 1.188,1.696 1.353,1.849 0.165,0.153 10 *b 0.934,1.792 1.188,1.792 false 0.572,2.527 0.738,2.680 0.165,0.153 10 *c 1.542,2.624 0.755,2.624 false 2.406,1.696 2.571,1.849 0.165,0.153 10 *b 2.151,1.792 2.406,1.792 false 2.656,0.281 2.821,0.435 0.165,0.153 10 *a 2.51,0.378 2.656,0.378 false

Connect the brake actuator hose to the brake booster pump assembly.

Text in Illustration
*A for Type A
*B for Type B
*a Identification Mark (Red)
*b Identification Mark (Yellowish Green)
*c Rib (Unpainted)

NOTICE:
·

Make sure that the identification mark (yellowish green) on the brake actuator hose is positioned within 30° of the brake booster pump rib.

·

Make sure to install the hose to the proper location.




b.

Move the clip to secure the brake actuator hose.

C274356E02
0.604,0.104 0.927,0.313 0.323,0.208 12 true *A 4.083,0.073 4.406,0.344 0.323,0.271 12 true *B 1.854,1.646 2.198,1.813 0.344,0.167 10 false 135° 1.875,2.354 2.219,2.521 0.344,0.167 10 false 145° 5.354,1.635 5.698,1.802 0.344,0.167 10 false 135° 5.344,2.354 5.688,2.521 0.344,0.167 10 false 145°

Text in Illustration
*A for Type A *B for Type B
V100136

Front of Vehicle - -

NOTICE:

Install the clip within the range shown in the illustration.



Hide 47210L 8.INSTALL BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY