Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE BOOSTER(for LHD) › 2011.12–2014.12
RM2170E _54 Brake _057022 BRAKE SYSTEM (OTHER) _0278034 BRAKE BOOSTER(for LHD) A

BRAKE SYSTEM (OTHER)  BRAKE BOOSTER(for LHD)  INSTALLATION  


PROCEDURE

Hide 44785C 1.INSTALL BRAKE BOOSTER GASKET

a.

Install a new brake booster gasket to the brake booster with master cylinder assembly.


Hide 47210L 2.INSTALL BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

a.
C250004E01
2.102,2.598 2.268,2.746 0.166,0.149 10 *1 0.382,2.821 0.548,2.969 0.166,0.149 10 *2 2.274,4.223 2.440,4.371 0.166,0.149 10 *5 1.648,2.692 2.102,2.692 false 3.142,2.884 3.308,3.033 0.166,0.149 10 *3 2.83,2.978 3.142,2.978 false 2.79,3.17 2.956,3.318 0.166,0.149 10 *4 2.478,3.264 2.79,3.264 false 1.629,3.323 0.576,2.927 0.576,2.927 1.216,3.551 false 1.711,3.897 2.274,4.303 2.274,4.303 1.503,4.278 false

Install the brake booster with master cylinder assembly with the 4 nuts.

Text in Illustration
*1 Connector Portion
*2 Union
*3 Push Rod Clevis
*4 Boot
*5 Front No. 2 Brake Tube

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not carry the brake booster with master cylinder assembly by the portion shown in bold in the illustration.

·

Be careful not to allow brake fluid to enter the connector.

·

If installing a new brake booster with master cylinder assembly, do not remove the hole plugs before connecting the brake lines because the brake booster with master cylinder is filled with brake fluid.




b.
U159491E03
1.438,1.667 2.76,1.667 true 1.417,1.542 2.479,1.542 true 1.417,1.427 2.229,1.427 true 1.396,1.313 1.979,1.313 true 1.302,1.115 1.135,1.292 1.135,1.292 0.833,1.292 true 2.76,1.573 2.917,1.719 0.156,0.146 10 false *d 2.479,1.448 2.635,1.594 0.156,0.146 10 true *c 2.229,1.333 2.385,1.479 0.156,0.146 10 true *b 1.979,1.219 2.135,1.365 0.156,0.146 10 true *a 0.656,1.188 0.813,1.333 0.156,0.146 10 false *e

Temporarily tighten each brake line to the correct position on the brake booster with master cylinder assembly as shown in the illustration.

Text in Illustration
*a to Front Wheel Cylinder LH
*b to Rear Wheel Cylinder RH
*c to Brake Booster Pump Assembly
*d to Rear Wheel Cylinder LH
*e to Front Wheel Cylinder RH


c.

Using a union nut wrench, fully tighten each brake line.

Torque:
15 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:
·

Do not kink or damage the brake lines.

·

Use the formula to calculate special torque values for situations where the union nut wrench is combined with a torque wrench (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).




d.
C250027

Connect the connector to the brake booster with master cylinder assembly.

Text in Illustration
V100135

Connect the connector
V100136

Lock the lock lever

NOTICE:
·

Make sure that the connector can be connected smoothly. Do not allow foreign matter to enter.

·

Make sure that the connector lock is locked securely.




Hide 47381N 3.INSTALL TUBE CLAMP BRACKET

a.
C250025E05
1.677,3.844 1.104,3.844 true 1.792,2.052 0.844,2.052 true 2.354,1.396 2.563,1.573 0.208,0.177 10 false (1) 2.271,2 2.479,2.177 0.208,0.177 10 true (2) 0.906,3.75 1.083,3.906 0.177,0.156 10 true *a 0.646,1.969 0.823,2.125 0.177,0.156 10 true *1

Temporarily install the tube clamp bracket to the brake booster with master cylinder assembly with the front No. 1 brake tube and 2 bolts.

Text in Illustration
*1 Front No. 1 Brake Tube
*a The tube clamp bracket contacts the brake booster with master cylinder assembly.


b.

Tighten the 2 bolts in the order shown in the illustration.

Torque:
Bolt (1) : 8.0 N*m (82 kgf*cm, 71 in.*lbf)
Bolt (2) : 7.0 N*m (71 kgf*cm, 62 in.*lbf)

NOTICE:

When tightening the bolt (1), be sure that the tube clamp bracket contacts the brake booster with master cylinder assembly.



Hide 44571 4.CONNECT BRAKE ACTUATOR HOSE

a.
C250023E01
2.443,2.004 2.751,2.159 0.308,0.154 10 360°

Connect the brake actuator hose to the brake master cylinder reservoir assembly with the clip.

Text in Illustration
V100136

Front of Vehicle

NOTICE:
·

Make sure that the identification mark on the brake actuator hose is positioned within 30° of the brake master cylinder reservoir assembly rib.

·

Make sure to install the hose to the proper location.

·

Install the clip within the range shown in the illustration.




Hide 47233 5.INSTALL RESERVOIR BRACKET

a.

Install the reservoir bracket with the 2 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 47234L 6.CONNECT NO. 1 RESERVOIR HOSE

a.
C250020E01
2.433,0.164 2.760,0.319 0.327,0.155 10 180°

Connect the No. 1 reservoir hose to the brake booster with master cylinder assembly with the clip.

Text in Illustration
V100136

Up

NOTICE:
·

Make sure that the identification mark on the No. 1 reservoir hose is positioned within 30° of the brake booster with master cylinder assembly rib.

·

When connecting the reservoir hose, face the identification mark up.

·

Make sure to install the hose to the proper location.

·

Install the clip within the range shown in the illustration.




Hide 47235G 7.CONNECT NO. 2 RESERVOIR HOSE

a.
C250018E01
2.412,0.151 2.724,0.298 0.312,0.147 10 180°

Connect the No. 2 reservoir hose to the brake booster with master cylinder assembly with the clip.

Text in Illustration
V100136

Up

NOTICE:
·

Make sure that the identification mark on the No. 2 reservoir hose is positioned within 30° of the brake booster with master cylinder assembly rib.

·

When connecting the reservoir hose, face the identification mark up.

·

Make sure to install the hose to the proper location.

·

Install the clip within the range shown in the illustration.




Hide 47220D 8.INSTALL BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY

a.

Install the brake master cylinder reservoir assembly with the 2 nuts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 47101A 10.INSTALL BRAKE PEDAL RETURN SPRING

Hide 11.FILL RESERVOIR WITH BRAKE FLUID

Hide 12.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 14.INSPECT AND ADJUST BRAKE PEDAL

Hide 15. OBTAIN ZERO POINT OF YAW RATE AND ACCELERATION SENSOR

HINT:

After the brake booster with master cylinder assembly is replaced, obtain the zero point of the yaw rate and acceleration sensor (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>CALIBRATION).


Hide 55701J 16.INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY

a.
C250015E02
2.5,3.167 2.698,3.344 0.198,0.177 10 true (1) 0.781,2.813 0.969,2.979 0.188,0.167 10 true (2)

Install the outer cowl top panel sub-assembly with the 8 bolts and nut.

Torque:
Bolt : 7.0 N*m (71 kgf*cm, 62 in.*lbf)
Nut : 12 N*m (122 kgf*cm, 9 ft.*lbf)

NOTICE:

Tighten the 2 bolts (1) and (2) first, and then tighten the rest of the bolts and nut.



b.

Engage the clamp to install the wire harness.


Hide 55815E 17.INSTALL FRONT NO. 1 VENTILATOR SEAL

a.

Engage the clamp to install the front No. 1 ventilator seal to the outer cowl top panel sub-assembly.


Hide 55735B 18.INSTALL FRONT AIR SHUTTER SEAL

a.

Engage the clamp to install the front air shutter seal to the outer cowl top panel sub-assembly.


Hide 55722C 19.INSTALL INNER COWL TOP TO COWL BRACE

a.
C250011E02
2.104,0.385 2.313,0.563 0.208,0.177 10 true (1) 1.625,1.25 1.854,1.469 0.229,0.219 10 true (2) 1.031,0.302 1.24,0.479 0.208,0.177 10 false (3)

Install the inner cowl top to cowl brace to the outer cowl top panel sub-assembly with the 3 bolts.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)

NOTICE:

Tighten the 3 bolts in the order shown in the illustration.



Hide 20.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY