Home › Brake › BRAKE (REAR) › REAR BRAKE › from 2014.12
RM2170E _54 Brake _057024 BRAKE (REAR) _0278038 REAR BRAKE A

BRAKE (REAR)  REAR BRAKE  REMOVAL  


CAUTION / NOTICE / HINT

NOTICE:
·

When the brake pedal is first depressed after replacing the brake shoes or pushing back the wheel brake cylinder piston, DTC C1214 may be output. As there is no malfunction, clear the DTC.

·

While the auxiliary battery is connected, even if the power switch is off, the brake control system activates when the brake pedal is depressed or the door courtesy switch is turned on. Therefore, even if only brake shoes are to be removed and installed, be sure to perform the Disable Brake Control procedure and disconnect the cable from the negative (-) terminal of the auxiliary battery before beginning work.



HINT:
·

Use the same procedure for the LH side and RH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 3.REMOVE REAR WHEEL

Hide 4.DRAIN BRAKE FLUID

NOTICE:

Immediately wash off any brake fluid that comes into contact with any painted surfaces.


Hide 42403 6.REMOVE REAR BRAKE DRUM SUB-ASSEMBLY

a.
C233134

Release the parking brake and remove the rear brake drum.

Text in Illustration
V100135

Contract

HINT:

If the rear brake drum cannot be removed easily, perform the following procedure.


i.

Remove the shoe adjusting hole plug and insert a screwdriver through the hole into the backing plate, and hold the automatic adjust lever away from the adjuster.


ii.

Using another screwdriver, contract the brake shoe by turning the adjusting bolt.



Hide 04943A 7.REMOVE REAR BRAKE STRUT KIT

a.
C249598E01
2.87,0.246 3.029,0.394 0.159,0.148 10 *1 3.058,0.883 3.218,1.046 0.160,0.163 10 *2 0.243,1.531 0.551,1.685 0.308,0.155 10 SST 2.104,0.564 2.338,0.33 2.338,0.33 2.859,0.33 false 1.364,1.618 0.605,1.618 false 1.933,0.79 2.115,0.972 2.115,0.972 3.053,0.972 false

Using SST, separate the tension spring from the rear brake shoe.

Text in Illustration
*1 Wheel Cylinder Boot
*2 Tension Spring

SST
09921-00011  

NOTICE:

Do not damage the wheel cylinder boot.



b.
C249599E01
0.253,1.281 0.555,1.444 0.302,0.163 10 SST 1.515,1.36 0.622,1.36 false

Using SST, remove the 2 shoe hold down spring cups, shoe hold down spring, pin and rear brake shoe.

SST
09718-00011  


c.
C250559

Remove the shoe tension spring.


d.
C249604E01
2.926,1.377 3.234,1.521 0.308,0.144 10 SST 2.111,1.451 2.919,1.451 false

Using SST, remove the 2 shoe hold down spring cups, shoe hold down spring, pin and rear brake shoe.

SST
09718-00011  


e.
C249605

Remove the tension spring from the rear brake shoe and remove the rear brake strut kit.


Hide 46430 8.SEPARATE NO. 3 PARKING BRAKE CABLE ASSEMBLY

a.
C108972

Using needle-nose pliers, separate the No. 3 parking brake cable assembly.


Hide 47644A 9.REMOVE REAR BRAKE AUTOMATIC ADJUST LEVER

a.
C233135

Remove the rear brake automatic adjust lever tension spring and rear brake automatic adjust lever.


Hide 47548R 10.REMOVE REAR DRUM BRAKE BLEEDER PLUG CAP

Hide 47547R 11.REMOVE REAR DRUM BRAKE BLEEDER PLUG

Hide 47570 12.REMOVE REAR WHEEL BRAKE CYLINDER ASSEMBLY

a.
C250563

Using a union nut wrench, disconnect the brake line from the rear brake wheel cylinder assembly.


b.
C250562

Remove the 2 bolts and rear wheel brake cylinder assembly from the backing plate.