Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM
RM2170E _55 Steering _057026 POWER ASSIST SYSTEMS _0278045 POWER STEERING SYSTEM C

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  C1551/51  IG Power Supply Voltage Malfunction  


DESCRIPTION

The power steering ECU assembly distinguishes the power switch status as on (IG) or off (lock) through the IG power source circuit.

DTC No. DTC Detection Condition Trouble Area
C1551/51 Open or short in IG power source circuit with power switch ON
·

ECU-IG No. 2 fuse

·

IG power source circuit

·

Power steering ECU assembly



WIRING DIAGRAM

C113532E82
0.406,1.052 1.74,1.198 1.333,0.146 10 false from IG1 No. 1 Relay 2.76,1.208 3.646,1.344 0.885,0.135 10 false ECU-IG No. 2 4.479,1.031 4.688,1.177 0.208,0.146 10 false G6 4.802,1.052 4.969,1.198 0.167,0.146 10 false IG 4.531,0.844 4.625,0.99 0.094,0.146 10 false 1 4.448,2.135 4.708,2.281 0.26,0.146 10 false A33 4.802,2.156 5.229,2.302 0.427,0.146 10 false PGND 4.542,1.948 4.635,2.094 0.094,0.146 10 false 2 4.615,2.917 6.802,3.177 2.188,0.26 10 false Power Steering ECU Assembly

CAUTION / NOTICE / HINT

NOTICE:

If the power steering ECU assembly has been replaced with a new one, perform assist map writing and the torque sensor zero point calibration (See page Steering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION).


HINT:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (IG POWER SUPPLY)
a.

Turn the power switch off (lock).


b.

Connect the intelligent tester to the DLC3.


c.

Turn the power switch on (IG).


d.

Turn the intelligent tester on.


e.

Enter the following menus: Chassis / EMPS / Data List.


f.

Select the item "IG power supply" in the Data List and read the value displayed on the intelligent tester.

EMPS
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
IG power supply IG power supply/
Min.: 0.0000 V
Max.: 20.1531 V
9 to 16 V Power switch on (IG)

OK:

The normal condition value is displayed on the intelligent tester.




OK

CHECK INTERMITTENT PROBLEMS

NG

2.CHECK HARNESS AND CONNECTOR (POWER STEERING ECU ASSEMBLY - BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (POWER STEERING ECU ASSEMBLY - BODY GROUND)
a.
C354336E01
0.583,1.75 1,2 0.417,0.25 1.01,2.729 1.438,2.094 false 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 0.688,1.792 1,1.99 0.313,0.198 10 false G6 0.906,2.74 1.219,2.938 0.313,0.198 10 false IG

C354337E01
0.333,1.917 0.75,2.167 0.417,0.25 2.26,3.031 2.073,2.625 false 0.094,0.115 0.406,0.313 0.313,0.198 10 false *a 0.406,1.958 0.844,2.229 0.438,0.271 10 false A33 2.146,3.073 2.667,3.344 0.521,0.271 10 false PGND

Disconnect the connectors from the power steering ECU assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G6-1 (IG) - Body ground Power switch on (IG) 9 to 16 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A33-2 (PGND) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Power Steering ECU Assembly)



OK

REPLACE POWER STEERING ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR