Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM
RM2170E _55 Steering _057026 POWER ASSIST SYSTEMS _0278045 POWER STEERING SYSTEM C

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  C1552/52  DC Motor Power Source Voltage Malfunction  C1554/54  EPS Relay Circuit  


DESCRIPTION

When a problem occurs in the system, the power source relay circuit and the motor relay circuit are shut off to stop the power assist. The ECU must be replaced when there is a problem with the relays because the relays are built into the ECU.

DTC No. DTC Detection Condition Trouble Area
C1552/52 PIG power source circuit malfunction
·

EPS fuse

·

PIG power source circuit

·

Power steering ECU assembly


C1554/54 Power source relay circuit malfunction
·

EPS fuse

·

PIG power source circuit

·

Power steering ECU assembly



WIRING DIAGRAM

C246150E05
4.604,0.706 4.930,0.886 0.326,0.180 10 PIG 4.464,2.975 4.790,3.156 0.326,0.180 10 A33 4.394,0.601 4.539,0.781 0.145,0.180 10 1 4.394,2.065 4.548,2.245 0.154,0.180 10 2 4.604,2.156 5.055,2.336 0.451,0.180 10 PGND 2.601,0.895 2.927,1.075 0.326,0.180 10 EPS 1.186,1.273 1.598,1.453 0.413,0.180 10 MAIN 1.298,2.331 2.377,2.511 1.080,0.180 10 Auxiliary Battery 4.464,3.165 6.436,3.345 1.972,0.180 10 Power Steering ECU Assembly

CAUTION / NOTICE / HINT

NOTICE:

If the power steering ECU assembly has been replaced with a new one, perform assist map writing and the torque sensor zero point calibration (See page Steering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION).


HINT:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER
a.

Turn the power switch off (lock).


b.

Connect the intelligent tester to the DLC3.


c.

Turn the power switch on (ready).


d.

Turn the intelligent tester on.


e.

Enter the following menus: Chassis / EMPS / Data List.


f.

Select the item "PIG power supply" in the Data List and read the value displayed on the intelligent tester.

EMPS
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
PIG Power Supply Power source voltage to activate motor/
Min.: 0.0000 V
Max.: 20.1531 V
9 to 16 V Always

OK:

The normal condition value is displayed on the intelligent tester.




OK

CHECK INTERMITTENT PROBLEMS

NG

2.CHECK HARNESS AND CONNECTOR (AUXILIARY BATTERY - POWER STEERING ECU ASSEMBLY - BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (AUXILIARY BATTERY - POWER STEERING ECU ASSEMBLY - BODY GROUND)
a.
U159492E01
0.328,1.717 0.596,1.873 0.267,0.156 10 A33 0.181,0.156 0.333,0.312 0.152,0.156 10 *a 0.868,2.906 1.136,3.062 0.268,0.156 10 PIG 1.369,2.291 1.048,2.884 false 2.261,2.906 2.684,3.062 0.423,0.156 10 PGND 2.072,2.291 2.392,2.884 false

Disconnect the connector from the power steering ECU assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A33-1 (PIG) - Body ground Always 9 to 16 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A33-2 (PGND) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Power Steering ECU Assembly)



OK

REPLACE POWER STEERING ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR