Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM › 2011.12–2014.12
RM2170E _55 Steering _057026 POWER ASSIST SYSTEMS _0278045 POWER STEERING SYSTEM U

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  DATA LIST / ACTIVE TEST  


DATA LIST


HINT:

Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Turn the power switch off (lock).


b.

Connect the intelligent tester to the DLC3.


c.

Turn the power switch on (IG).


d.

Turn the intelligent tester on.


e.

Enter the following menus: Chassis / EMPS / Data List.


f.

According to the display on the intelligent tester, read the "Data List".



EMPS
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Meter Vehicle Velocity Vehicle speed from meter/
Min.: 0.0 km/h (0.0mph)
Max.: 300.0 km/h (186.4 mph)
0 km/h (0 mph) Power switch on (ready) and vehicle stopped
No significant fluctuation Power switch on (ready) and vehicle driven at constant speed
Motor Actual Current Current to motor/
Min.: -327.68 A
Max.: 327.67 A
Value changes in proportion to steering effort
-The value increases when turning right and decreases when turning left
Power switch on (ready) and steering wheel being turned
Command Value Current Requested current to motor/
Min.: -327.68 A
Max.: 327.67 A
Value changes in proportion to steering effort
-The value increases when turning right and decreases when turning left
Power switch on (ready) and steering wheel being turned
Thermistor Temperature ECU substrate temperature/
Min.: -50.0°C (-58.0°F)
Max.: 150.0°C (302.0°F)
-50 to 150°C (-58 to 302°F) -
PIG Power Supply Power source voltage to activate motor/
Min.: 0.0000 V
Max.: 20.1531 V
9 to 16 V Always
IG Power Supply ECU power source voltage/
Min.: 0.0000 V
Max.: 20.1531 V
9 to 16 V Power switch on (IG)
Steering Wheel Torque Steering wheel torque/
Min.: -327.68 Nm
Max.: 7.00 Nm
Value changes in proportion to steering effort Power switch on (ready) and steering wheel being turned
Torque Sensor 1 Output Torque sensor 1 output value/
Min.: 0.0000 V
Max.: 4.9725 V
2.3 to 2.7 V Power switch on (ready) and steering wheel not being turned (without load)
2.5 to 3.8 V Power switch on (ready) and steering wheel being turned to right with vehicle stopped
1.2 to 2.5 V Power switch on (ready) and steering wheel being turned to left with vehicle stopped
Torque Sensor 2 Output Torque sensor 2 output value/
Min.: 0.0000 V
Max.: 4.9725 V
2.3 to 2.7 V Power switch on (ready) and steering wheel not being turned (without load)
1.2 to 2.5 V Power switch on (ready) and steering wheel being turned to right with vehicle stopped
2.5 to 3.8 V Power switch on (ready) and steering wheel being turned to left with vehicle stopped
TRQ1 Zero Point Value Zero point value of torque sensor 1/
Min.: 0.0000 V
Max.: 4.9725 V
2.3 to 2.7 V Power switch on (ready) and steering wheel not being turned (without load)
TRQ2 Zero Point Value Zero point value of torque sensor 2/
Min.: 0.0000 V
Max.: 4.9725 V
2.3 to 2.7 V Power switch on (ready) and steering wheel not being turned (without load)
Motor Terminal Volt(+) Motor terminal M1 voltage/
Min.: 0.0 V
Max.: 25.5 V
9 to 16 V Power switch on (ready) and steering wheel being turned to right
6 to 8 V Power switch on (ready) and steering wheel being turned to left
Motor Terminal Volt(-) Motor terminal M2 voltage/
Min.: 0.0 V
Max.: 25.5 V
6 to 8 V Power switch on (ready) and steering wheel being turned to right
9 to 16 V Power switch on (ready) and steering wheel turned to left
IG ON/OFF Times Number of times of power switch ON/OFF after fail detection/
Min.: 0 time
Max.: 65535 times
- This value indicates the number of times of IG ON/OFF after the latest DTC detection.
Motor Overheat Record Continuous overheat prevention control record/
Unrec or Rec
Unrec -
Motor Lo Power Record PIG power source voltage drop record/
Unrec or Rec
Unrec -
Eng Rev Inter Record Record of power switch on (IG) signal interruption/
Unrec or Rec
Unrec -
Spd Sig Invalid Record Vehicle speed signal invalid record/
Unrec or Rec
Unrec -
Battery Voltage Lo Record Auxiliary battery voltage reduction history/
Min.: 0 times, Max.: 65535 times
0 to 65535 -
Ready Status Ready status/
READY or OFF
READY or OFF -
The Number of DTCs Number of detected DTCs when freeze frame data stored/
Min.: 0
Max.: 255
0 to 255 -