Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM › 2011.12–2014.12
RM2170E _55 Steering _057026 POWER ASSIST SYSTEMS _0278045 POWER STEERING SYSTEM D

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  FREEZE FRAME DATA  


FREEZE FRAME DATA


NOTICE:
·

Freeze frame data values will vary depending on the measurement conditions, surroundings, or vehicle conditions. For this reason, there may be a problem even if the values are within specifications.

·

Turn the power switch on (IG) and park the vehicle on level ground. Check the freeze frame data by using the intelligent tester.



a.

Turn the power switch off (lock).


b.

Connect the intelligent tester to the DLC3.


c.

Turn the power switch on (IG).


d.

Turn the intelligent tester on.


e.

Check the freeze frame data on the intelligent tester.

EMPS
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Meter Vehicle Velocity Vehicle speed from meter/
Min.: 0.0 km/h (0.0mph)
Max.: 300.0 km/h (186.4 mph)
0 km/h (0 mph) Power switch on (ready) and vehicle stopped
No significant fluctuation Power switch on (ready) and vehicle driven at constant speed
Motor Actual Current Current to motor/
Min.: -327.68 A
Max.: 327.67 A
Value changes in proportion to steering effort
-The value increases when turning right and decreases when turning left
Power switch on (ready) and steering wheel being turned
Command Value Current Requested current to motor/
Min.: -327.68 A
Max.: 327.67 A
Value changes in proportion to steering effort
-The value increases when turning right and decreases when turning left
Power switch on (ready) and steering wheel being turned
Thermistor Temperature ECU substrate temperature/
Min.: -50.0°C (-58.0°F)
Max.: 150.0°C (302.0°F)
-50 to 150°C (-58 to 302°F) -
PIG Power Supply Power source voltage to activate motor/
Min.: 0.0000 V
Max.: 20.1531 V
9 to 16 V Always
IG Power Supply ECU power source voltage/
Min.: 0.0000 V
Max.: 20.1531 V
9 to 16 V Power switch on (IG)
Steering Wheel Torque Steering wheel torque/
Min.: -327.68 Nm
Max.: 7.00 Nm
Value changes in proportion to steering effort
-The value increases when turning left and decreases when turning right
Power switch on (ready) and steering wheel being turned
Torque Sensor 1 Output Torque sensor 1 output value/
Min.: 0.0000 V
Max.: 4.9725 V
2.3 to 2.7 V Power switch on (ready) and steering wheel not being turned (without load)
2.5 to 3.8 V Power switch on (ready) and steering wheel being turned to right with vehicle stopped
1.2 to 2.5 V Power switch on (ready) and steering wheel being turned to left with vehicle stopped
Torque Sensor 2 Output Torque sensor 2 output value/
Min.: 0.0000 V
Max.: 4.9725 V
2.3 to 2.7 V Power switch on (ready) and steering wheel not being turned (without load)
1.2 to 2.5 V Power switch on (ready) and steering wheel being turned to right with vehicle stopped
2.5 to 3.8 V Power switch on (ready) and steering wheel being turned to left with vehicle stopped
TRQ1 Zero Point Value Zero point value of torque sensor 1/
Min.: 0.0000 V
Max.: 4.9725 V
2.3 to 2.7 V Power switch on (ready) and steering wheel not being turned (without load)
TRQ2 Zero Point Value Zero point value of torque sensor 2/
Min.: 0.0000 V
Max.: 4.9725 V
2.3 to 2.7 V Power switch on (ready) and steering wheel not being turned (without load)
Motor Terminal Volt(+) Motor terminal M1 voltage/
Min.: 0.0 V
Max.: 25.5 V
9 to 16 V Power switch on (ready) and steering wheel being turned to right
6 to 8 V Power switch on (ready) and steering wheel being turned to left
Motor Terminal Volt(-) Motor terminal M2 voltage/
Min.: 0.0 V
Max.: 25.5 V
6 to 8 V Power switch on (ready) and steering wheel being turned to right
9 to 16 V Power switch on (ready) and steering wheel being turned to left
Ready Status Ready status/
Ready or OFF
READY or OFF -