Home › Steering › STEERING COLUMN › STEERING LOCK SYSTEM › 2011.12–2014.12
RM2170E _55 Steering _057027 STEERING COLUMN _0278046 STEERING LOCK SYSTEM C

STEERING COLUMN  STEERING LOCK SYSTEM  B2781  Open / Short in Steering Lock ECU  


DESCRIPTION

The steering lock ECU and steering lock motor are built into the steering lock actuator assembly.

The steering lock ECU detects whether the steering lock is in the lock or unlock position by using the lock position sensor of the steering lock motor.

The steering lock ECU receives lock and unlock request signals from the certification ECU (smart key ECU assembly) and responds with lock and unlock operation signals.

HINT:

The steering lock ECU is not connected to the CAN communication system. However, the steering lock ECU is connected to the certification ECU (smart key ECU assembly) via LIN communication and communicates with other components via CAN communication through the certification ECU (smart key ECU assembly).


DTC No. Detection Condition Trouble Area DTC Output Confirmation Operation
B2781 One of the following conditions is met (1-trip detection logic*1):
·

The steering lock/unlock position sensor is malfunctioning.*2

·

The steering lock motor activation circuit has a short circuit.

·

The steering lock motor activation circuit has an open circuit.


·

Steering lock ECU (Steering lock actuator assembly)

·

LIN communication system


No confirmation operation is necessary (monitoring is continuous).

*1: Only output while a malfunction is present and the power switch is on (IG).

*2: When both detection switches turn on, the system is determined to be malfunctioning.


C359223E01
2.167,2.198 2.833,1.75 2.833,1.75 4.083,1.75 false 3.75,1.75 3.583,1.521 false 0.167,0.438 0.635,0.865 0.469,0.427 10 false Unlock Sensor 0.958,3.354 2.406,3.656 1.448,0.302 10 false : Normal operation 1.698,2.917 3.573,3.292 1.875,0.375 10 false Lock operation conditions met 4.25,2.917 6.396,3.271 2.146,0.354 10 false Unlock operation conditions met 4.135,1.667 4.896,2.052 0.76,0.385 10 false Example of Malfunction 0.969,1.01 1.396,1.323 0.427,0.313 10 false ON 0.969,1.313 1.396,1.625 0.427,0.313 10 false OFF 0.156,1.865 0.646,2.25 0.49,0.385 10 false Lock Sensor 0.948,2.51 1.375,2.823 0.427,0.313 10 false OFF 0.958,2.198 1.385,2.51 0.427,0.313 10 false ON

Vehicle Condition and Fail-safe Function when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
The steering cannot be locked or unlocked. For this reason, the hybrid control system cannot be started. Prohibits the hybrid control system from being started.

Related Data List and Active Test Items
DTC No. Data List Item Active Test Item
B2781
Entry&Start
·

Sensor Value

·

Motor Driver Short


-

CAUTION / NOTICE / HINT

NOTICE:
·

When using the intelligent tester with the power switch off, perform either of the following: 1) Turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the intelligent tester and vehicle begins, or 2) connect the intelligent tester to the vehicle and select "Manual" from the initial screen on the intelligent tester. Select "Key Code Registration" under model code.

·

After performing repairs, confirm that no DTCs are output again (See page Steering>STEERING COLUMN>STEERING LOCK SYSTEM>DTC CHECK / CLEAR).

·

When replacing the steering lock ECU (steering lock actuator assembly), registration must be performed (refer to Service Bulletin).



HINT:

When all the ECUs that are connected to the LIN communication cannot communicate with the certification ECU (smart key ECU assembly), DTC B2785 is stored.


PROCEDURE

1.CHECK DTC
a.

Using the intelligent tester, check if LIN communication DTC B2785 is output (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

HINT:

If a LIN communication DTC is output, perform troubleshooting for the LIN communication system (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).


Result:
Result Proceed to
DTC B2785 is output. A
DTC B2785 is not output. B




A

GO TO LIN COMMUNICATION SYSTEM (DTC B2785)

B

REPLACE STEERING LOCK ACTUATOR ASSEMBLY