Home › Steering › STEERING COLUMN › STEERING LOCK SYSTEM › from 2014.12
RM2170E _55 Steering _057027 STEERING COLUMN _0278046 STEERING LOCK SYSTEM C

STEERING COLUMN  STEERING LOCK SYSTEM  B2788  IG2 Signal Malfunction  


DESCRIPTION

This DTC is stored when the steering lock ECU detects an IG2 power supply malfunction.

HINT:

The steering lock ECU is not connected to the CAN communication system. However, the steering lock ECU is connected to the certification ECU (smart key ECU assembly) via LIN communication and communicates with other components via CAN communication through the certification ECU (smart key ECU assembly).


DTC No. Detection Condition Trouble Area DTC Output Confirmation Operation
B2788 Mismatch between the steering lock ECU IG2 input from the LIN communication system and from the direct line (1-trip detection logic*).
·

IG2 NO. 2 fuse

·

Steering lock ECU (Steering lock actuator assembly)

·

Harness or connector


No confirmation operation is necessary (monitoring is continuous).

*: Only output while a malfunction is present and the power switch is on (IG).


Vehicle Condition and Fail-safe Function when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
The steering cannot be locked or unlocked. For this reason, the hybrid control system cannot be started. -

Related Data List and Active Test Items
DTC No. Data List Item Active Test Item
B2788 - -

WIRING DIAGRAM

C251137E09
0.917,0.677 1.188,0.875 0.271,0.198 10 false LIN 1.26,0.5 1.448,0.698 0.188,0.198 10 false 17 0.063,3.073 0.385,3.365 0.323,0.292 10 false G79 0.375,3.073 1.906,3.531 1.531,0.458 10 false Certification ECU (Smart Key ECU Assembly) 4.833,3.083 5.531,3.385 0.698,0.302 10 false G50 5.167,3.083 6.958,3.542 1.792,0.458 10 false Steering Lock ECU (Steering Lock Actuator Assembly) 5.375,2.281 5.708,2.479 0.333,0.198 10 false GND 5.375,1.531 5.708,1.729 0.333,0.198 10 false IG2 5.188,1.406 5.375,1.604 0.188,0.198 10 false 6 5.188,2.167 5.375,2.365 0.188,0.198 10 false 1 5.375,0.635 5.708,0.833 0.333,0.198 10 false LIN 5.188,0.479 5.375,0.677 0.188,0.198 10 false 5 2.75,3.396 4.469,3.646 1.719,0.25 10 false LIN Communication Line 3.844,1.688 4.615,1.938 0.771,0.25 10 false IG2 NO. 2 1.792,1.51 2.906,1.823 1.115,0.313 10 false from IG2 Relay

CAUTION / NOTICE / HINT

NOTICE:
·

When using the intelligent tester with the power switch off, perform either of the following: 1) Turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the intelligent tester and vehicle begins, or 2) connect the intelligent tester to the vehicle and select "Manual" from the initial screen on the intelligent tester. Select "Key Code Registration" under model code.

·

The steering lock system uses LIN communication. First perform the inspections in "How to Proceed with Troubleshooting" to confirm that there are no communication malfunctions before proceeding with troubleshooting (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

After performing repairs, confirm that no DTCs are output again (See page Steering>STEERING COLUMN>STEERING LOCK SYSTEM>DTC CHECK / CLEAR).

·

When replacing the steering lock ECU (steering lock actuator assembly), registration must be performed (refer to Service Bulletin).



PROCEDURE

1.INSPECT STEERING LOCK ECU (POWER SOURCE MODE SIGNAL)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


b.

Disconnect the G50 steering lock ECU connector.


c.
U159321E01
0.377,0.3 0.605,0.476 0.227,0.176 10 *a 0.418,0.973 0.727,1.115 0.309,0.142 10 G50 0.818,1.558 1.176,1.742 0.357,0.184 10 GND 1.281,2.42 1.032,1.733 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G50-1 (GND) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Steering Lock ECU (Steering Lock Actuator Assembly))


d.

Reconnect the G50 steering lock ECU connector.


e.
U159320E02
2.26,1.958 2.802,2.823 false 1.396,1.948 1,2.823 false 0.365,0.271 0.625,0.479 0.26,0.208 10 false *a 0.823,2.854 1.156,3.01 0.333,0.156 10 false IG2 2.635,2.854 3.01,3.01 0.375,0.156 10 false GND 0.313,0.969 0.625,1.115 0.313,0.146 10 false G50

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G50-6 (IG2) - G50-1 (GND) Power switch on (IG) 11 to 14 V
G50-6 (IG2) - G50-1 (GND) Power switch off Below 1 V


Text in Illustration
*a Component with harness connected
(Steering Lock ECU (Steering Lock Actuator Assembly))



OK

REPLACE STEERING LOCK ACTUATOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR