Home › Steering › STEERING GEAR / LINKAGE › STEERING GEAR › 2015.11–2017.06
RM2170E _55 Steering _057028 STEERING GEAR / LINKAGE _0278051 STEERING GEAR A

STEERING GEAR / LINKAGE  STEERING GEAR  INSTALLATION  


PROCEDURE

Hide 45047 1.INSTALL TIE ROD END SUB-ASSEMBLY LH

a.
C187022E11
0.99,1.219 0.99,1.573 0.99,1.573 1.583,1.573 true 1.365,1.219 1.365,1.573 true 1.594,1.469 1.781,1.625 0.188,0.156 10 false *a

Install the lock nut and tie rod end sub-assembly LH to the steering gear assembly until the matchmarks are aligned.

Text in Illustration
*a Matchmark

HINT:

After adjusting the toe-in, tighten the lock nut.



Hide 45046 2.INSTALL TIE ROD END SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 3.INSTALL STEERING LINK ASSEMBLY

a.
C244486

Install the steering link assembly to the front suspension crossmember sub-assembly with the 2 bolts and 2 nuts.

Torque:
79 N*m (800 kgf*cm, 58 ft.*lbf)

NOTICE:
·

Keep the nut from rotating while turning the bolt because the nut has its own stopper.

·

Make sure to tighten the bolts starting from the right side of the vehicle.




Hide 45025D 4.INSTALL NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY

a.

Install the No. 1 steering column hole cover subassembly to the steering link assembly.


Hide 51201 5.INSTALL FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

a.

Support the front suspension crossmember sub-assembly with an engine lifter using 4 attachments or equivalent tools.

NOTICE:
·

Make sure to secure the front suspension crossmember sub-assembly to prevent it from dropping.

·

Use the attachments to keep the front suspension crossmember sub-assembly level.

·

The front suspension crossmember sub-assembly is a heavy component. Make sure that it is supported securely.




b.

Temporarily tighten the front suspension crossmember sub-assembly to the body with the 6 bolts.


c.

Tighten the 2 bolts A, 2 bolts B and 2 bolts C on the left and right sides while alternately inserting SST into the left and right side reference holes in the front suspension crossmember sub-assembly.

C249877E04
2.229,4.25 2.5,4.25 true 4.917,4.25 4.646,4.25 true 1.448,1.479 1.573,1.635 0.125,0.156 10 true A 1.625,2.135 1.75,2.292 0.125,0.156 10 true B 1.51,2.531 1.635,2.688 0.125,0.156 10 false C 5.396,2.135 5.521,2.292 0.125,0.156 10 true B 5.479,2.531 5.604,2.688 0.125,0.156 10 true C 5.563,1.479 5.688,1.635 0.125,0.156 10 true A 2.521,4.167 2.823,4.354 0.302,0.188 10 true SST 4.375,4.177 4.677,4.365 0.302,0.188 10 true SST 1.604,5.51 1.76,5.656 0.156,0.146 10 false *a 2.479,5.51 2.635,5.656 0.156,0.146 10 false *b 5.031,5.51 5.188,5.656 0.156,0.146 10 false *a 5.917,5.51 6.073,5.656 0.156,0.146 10 false *b

SST
09670-00010  

Text in Illustration
*a OK *b NG
V100136

Front of the Vehicle - -

Torque:
Bolt A : 87 N*m (887 kgf*cm, 64 ft.*lbf)
Bolt B : 151 N*m (1540 kgf*cm, 111 ft.*lbf)
Bolt C : 98 N*m (999 kgf*cm, 72 ft.*lbf)


d.

Lower the engine lifter.


e.

Install the engine moving control rod with the bolt.

Torque:
120 N*m (1224 kgf*cm, 89 ft.*lbf)


Hide 48069 6.CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

Hide 48068 7.CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 45047 8.CONNECT TIE ROD END SUB-ASSEMBLY LH

a.
C249933

Connect the tie rod end sub-assembly LH to the steering knuckle with a new nut.

Torque:
49 N*m (500 kgf*cm, 36 ft.*lbf)

NOTICE:

Further tighten the nut up to 60° if the holes for the cotter pin are not aligned.



b.

Install a new cotter pin.


Hide 45046 9.CONNECT TIE ROD END SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 48810 10.INSTALL FRONT STABILIZER LINK ASSEMBLY LH

Hide 48820B 11.INSTALL FRONT STABILIZER LINK ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 45025D 12.CONNECT NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY

a.
C251686E03
0.667,0.375 1.417,0.375 false 2.25,1.833 2.927,1.833 false 0.333,1.51 0.281,1.667 false 0.521,0.292 0.656,0.469 0.135,0.177 10 false B 2.948,1.74 3.083,1.917 0.135,0.177 10 false A 0.188,1.656 0.365,1.833 0.177,0.177 10 false *a

Place clip A as shown in the illustration and engage clip B to the body to connect the No. 1 steering column hole cover sub-assembly.

Text in Illustration
*a Lip

NOTICE:

Make sure that the lip of the No. 1 steering column hole cover sub-assembly is not damaged.



Hide 45209 13.CONNECT STEERING SLIDING YOKE SUB-ASSEMBLY

Hide 45259A 14.INSTALL COLUMN HOLE COVER SILENCER SHEET

Hide 15.INSTALL FRONT WHEELS

Torque:
103 N*m (1050 kgf*cm, 76 ft.*lbf)

Hide 16. POSITION WHEELS FACING STRAIGHT AHEAD

Hide 18.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT