Home › Audio / Visual / Telematics › AUDIO / VIDEO › REAR DOOR SPEAKER
RM2170E _56 Audio / Visual / Telematics _057029 AUDIO / VIDEO _0278054 REAR DOOR SPEAKER A

AUDIO / VIDEO  REAR DOOR SPEAKER  INSTALLATION  


PROCEDURE

Hide 86160B 1.INSTALL REAR SPEAKER ASSEMBLY

a.

Using an air riveter or a hand riveter, install the rear speaker assembly with 3 new rivets.

E244889E03
4.104,2.969 6.958,5.646 2.854,2.677 4.104,0.25 6.958,2.927 2.854,2.677 0.51,2.969 3.365,5.646 2.854,2.677 6.063,1.042 6.531,1.646 6.531,1.646 6.052,2.354 false 5.625,1.208 5.208,1.625 5.208,1.625 5.677,2.104 false 1.229,3.938 0.927,3.938 false 1.167,3.167 0.917,3.167 false 1.229,4.99 0.917,4.99 false 4.802,3.438 4.531,3.438 false 4.802,4.656 4.521,4.656 false 6.5,2.302 6.656,2.448 0.156,0.146 10 false *b 6.5,0.958 6.656,1.104 0.156,0.146 10 false *a 6.573,1.573 6.729,1.719 0.156,0.146 10 false *2 5.021,1.583 5.177,1.729 0.156,0.146 10 false *1 2.938,5.271 3.094,5.417 0.156,0.146 10 false *b 2.938,3.438 3.094,3.583 0.156,0.146 10 false *a 2.938,4.281 3.094,4.427 0.156,0.146 10 false *a 0.771,3.094 0.927,3.24 0.156,0.146 10 false *1 0.771,3.865 0.927,4.01 0.156,0.146 10 false *1 0.771,4.906 0.927,5.052 0.156,0.146 10 false *1 6.563,4.927 6.719,5.073 0.156,0.146 10 false *b 6.563,3.75 6.719,3.896 0.156,0.146 10 false *a 4.375,3.365 4.531,3.51 0.156,0.146 10 false *1 4.365,4.604 4.521,4.75 0.156,0.146 10 false *1 2.427,0.802 2.625,0.969 0.198,0.167 10 true (1) 1.229,0.635 1.427,0.802 0.198,0.167 10 true (2) 1.573,1.667 1.771,1.833 0.198,0.167 10 true (3)

Text in Illustration
*1 Riveter *2 Mandrel
*a INCORRECT *b CORRECT

NOTICE:
·

Do not touch the cone part of the speaker.

·

Do not pry on the rivets with the riveter, as this will cause damage to the riveter and mandrel.

·

Confirm that the rivets are seated properly against the speaker.

·

Do not tilt the riveter when installing the rivets to the speaker.

·

Do not leave any clearance between the rivet heads and speaker.

·

Do not leave any clearance between the speaker and door. Firmly hold the 2 items together while installing the rivets.



HINT:
·

Install the rivets in the order shown in the illustration.

·

If the rivet cannot be cut, pull it once and cut it.




b.

Connect the connector.


Hide 67604 2.INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY

Hide 3.INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL

Hide 67673A 4.INSTALL REAR DOOR FRAME GARNISH